Sharp LC-60UD20KN (serv.man5) User Manual / Operation Manual ▷ View online
15
Checking signal strength and
channel strength (DVB-T/T2/C/S/S2)
channel strength (DVB-T/T2/C/S/S2)
If you install a DVB-T/T2/C/S/S2 antenna for the first
time or relocate it, you should adjust the alignment
of the antenna to receive a good reception while
checking the antenna setup screen.
time or relocate it, you should adjust the alignment
of the antenna to receive a good reception while
checking the antenna setup screen.
1
Go to “TV Menu” > “Setup” > “View setting” >
“Channel settings” > “Antenna setup-DIGITAL”.
“Channel settings” > “Antenna setup-DIGITAL”.
2
Press
a/b to select “Digital setup” or “Satellite
setup”, and then press
;.
E
Checking signal strength
3
Press
a/b to select “Signal strength”, and then
press
;.
Signal strength for DVB-T/T2/C
Supply voltage
CH No.
Current
Max.
Signal strength
Signal strength
Channel strength
Current
Max.
Quality
Signal strength for DVB-S/S2
Current
Max.
Signal strength
Signal strength
Channel strength
Current
Max.
Quality
E
Checking channel strength
4
Press
a/b to select “Channel strength”, and
then press
;.
• You can input a specified frequency band using the
0
_9 numeric buttons.
Channel strength of DVB-T/T2
Supply voltage
CH No.
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Channel strength
Current
Max.
Quality
Channel strength of DVB-C
Supply voltage
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Symbol rate
QAM modulation
Symbol rate
QAM modulation
Channel strength
Current
Max.
Quality
Channel strength of DVB-S/S2
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Symbol rate
Band
Symbol rate
Band
Channel strength
Current
Max.
Quality
Vert/Low
5
Position and align the antenna so that the
maximum possible values for “Signal strength”
and “Quality” are obtained.
maximum possible values for “Signal strength”
and “Quality” are obtained.
NOTE
• The values of “Signal strength” and “Quality” indicate
when to check the appropriate alignment of the
antenna.
antenna.
Supplying power to the antenna
You must supply power to the antenna in order
to receive digitally/terrestrially broadcast stations
after connecting the antenna cable to the antenna
terminal on the rear of the TV.
to receive digitally/terrestrially broadcast stations
after connecting the antenna cable to the antenna
terminal on the rear of the TV.
1
Go to “TV Menu” > “Setup” > “View setting” >
“Channel settings” > “Antenna setup-DIGITAL” >
“Supply voltage”.
“Channel settings” > “Antenna setup-DIGITAL” >
“Supply voltage”.
2
Press
c/d to select “On”, and then press ;.
Initial auto installation
16
Daily operation
Switching on/off
Turning on/off the power
Press
a on the TV or >a on the remote control
unit.
Standby mode
From standby, press
a on the TV or >a on the
remote control unit.
NOTE
• If you are not going to use this TV for a long period of
time, be sure to remove the AC cord from the AC outlet.
• Weak electric power is still consumed even when the TV
is turned off.
Switching between digital, satellite
and analogue broadcasts
and analogue broadcasts
Watching digital
broadcasts
broadcasts
Watching analogue
broadcasts
broadcasts
Watching satellite
broadcasts
broadcasts
NOTE
• If multiple satellite services are set, each time you press
the SAT button the channel switches as follows.
SAT1
SAT2
SAT3
SAT4
Changing channels
With
:r/s
With 0
_9
Selecting an external video source
Once the connection is made, press
b to display
the “INPUT” screen, and then press
b or
a/b to
switch over to the appropriate external source with
;.
;.
TV
INPUT
Switchable
CH list
NOTE
• You can also select an external video source from
“HOME” > “Input change”.
• Only HDMI inputs which are not set for “Input skip”
(Page 44) and properly connected inputs can be selected.
Watching TV
17
Selecting a sound mode
E
DTV/SAT mode
If multi sound modes are received, each time you
press
press
7 the mode switches as follows.
Audio (ENG)
STEREO
L/R
L
R
LR
CH A
CH B
CH AB
Audio (ENG)
CH A
Audio (ENG)
MONO
Press
c/d to select L or R sound when the
STEREO or DUAL MONO screen is displayed.
Audio (ENG)
STEREO
L/R
L
R
LR
NOTE
• The sound mode screen disappears in six seconds.
• Selectable items vary depending on the received
• Selectable items vary depending on the received
broadcasts.
• When the “Audio description setting” menu is set
to “On”, the audio description sound is selected
depending on the main audio.
depending on the main audio.
E
ATV mode
Each time you press
7, the mode switches as
shown in the following tables.
NICAM TV broadcasts selection
Signal
Selectable items
Stereo
NICAM STEREO, MONO
Bilingual
NICAM CH A, NICAM CH B, NICAM CH AB,
MONO
MONO
Monaural NICAM MONO, MONO
A2 TV broadcasts selection
Signal
Selectable items
Stereo
STEREO, MONO
Bilingual
CH A, CH B, CH AB
Monaural MONO
NOTE
• When no signal is input, the sound mode will display
“MONO”.
Channel display
You can display the channel information by pressing
p on the remote control unit.
p on the remote control unit.
DTV mode
ATV mode
Audio (ENG)
STEREO
Video
Subtitle
Subtitle
Off
>> New information
MONO
Auto
Subtitle
I
Four digit numbers (e.g., 0001) are displayed after
selecting the five Nordic countries in the country
setting or for some cable operators. Also, operator
profiles use four digits.
selecting the five Nordic countries in the country
setting or for some cable operators. Also, operator
profiles use four digits.
SAT mode
Audio (ENG)
STEREO
Video
Subtitle
Subtitle
Off
>> New information
J
Satellite channels are displayed by four digit numbers
(e.g., 0001).
(e.g., 0001).
K
You can set four satellite stations to “SAT1”, “SAT2“,
“SAT3“, “SAT4”.
“SAT3“, “SAT4”.
E
Time display in channel information
You can display the time information included in
DTV, SAT and teletext broadcasts.
DTV, SAT and teletext broadcasts.
NOTE
• Skip step 1 if receiving DTV/SAT broadcasts.
1
Select a TV channel (the time information is
automatically captured).
automatically captured).
2
Press
p. The channel display will appear on the
TV.
3
Press
p again within the several seconds
that the channel display is on the screen. Time
information will be shown in the lower-right
corner of the screen for several seconds.
information will be shown in the lower-right
corner of the screen for several seconds.
4
Even when you change the TV channel, you can
display the time information with steps 2 and 3
above.
display the time information with steps 2 and 3
above.
Operation without a remote control unit
You can operate the menu settings using the TV
control buttons.
control buttons.
TV control buttons
Remote control buttons
@
@
b
;
:r/s
a/b
i+/-
d/c
Watching TV
18
Favourite Channel Information
Before installation
This function allows you to group your favourite
channels in a separate list. Pre-setting “My
favourite” in advance allows you to select your
favourite channels more conveniently.
channels in a separate list. Pre-setting “My
favourite” in advance allows you to select your
favourite channels more conveniently.
NOTE
• “My Favourite” can only be used for DTV and SAT
modes, a separate list will be stored for each input
source DTV, SAT1/2/3/4.
source DTV, SAT1/2/3/4.
• The maximum number of channels you can register in
“My favourite” is:
− 50 for TV broadcast which will be allocated 001-050,
as favourite channel numbers
− 50 for Radio broadcast which will be allocated 051-
100, as favourite channel numbers and
− 50 for Data broadcast which will be allocated 101-
150, as favourite channel numbers
How to add / remove / move your favourite
channels
channels
Press the
; button to display the on-screen
channel list.
• If you have already set your favourite channels,
you will be able to see “CH list” or “My favourite”
depending on your previous selection.
depending on your previous selection.
Function buttons used to edit “My favourite”
Buttons
Description
R button
Add to “My favourite” list or remove
from “My favourite” list.
The “
from “My favourite” list.
The “
” mark will be added to or
removed from the selected channel.
B button
Move channel position in “My
favourite” list. (“My favourite”
channel numbers will be sequentially
allocated.)
favourite” list. (“My favourite”
channel numbers will be sequentially
allocated.)
NOTE
• If you delete a channel via the “Manual adjust” option
(“TV Menu” > “Setup” > “View setting” > “Channel
settings” > “Programme setup” > “Digital setting” >
“Manual adjust”), this will be deleted from both the “CH
list” and “My favourite” list.
settings” > “Programme setup” > “Digital setting” >
“Manual adjust”), this will be deleted from both the “CH
list” and “My favourite” list.
Selecting channels from “My favourite” list
1
How to move between “My favourite” list and
“CH list”.
“CH list”.
1
Press the
; button when you watching DTV
or SAT to bring up the “CH list”.
2
Press the
d key and select “My favourite”
list.
2
Move up and down the displayed channel list by
using the
using the
a/b keys then press the ; button
to select the desired channel.
NOTE
• When watching your favourite channels via “My
favourite” list, you can directly select other favourite
channel by entering the favourite channel number on the
remote control.
channel by entering the favourite channel number on the
remote control.
• Selecting the EPG function while using “My favourite”
channel list, will only show details for the favourite
channels you have added. (To view details of all
available channels via the EPG, please switch back to
“CH list” mode from “My favourite” by following the
steps shown in 1 (
channels you have added. (To view details of all
available channels via the EPG, please switch back to
“CH list” mode from “My favourite” by following the
steps shown in 1 (
1) and reselect “CH List” before
pressing the EPG button.)
Operator profile
In case your CI Plus CAM supports Operator Profile,
your CAM will inform you and guide you through the
Operator Profile installation.
When operator's profile is added by the CAM, it will
be displayed in the CH list menu. Each profile will be
stored as an independent list in the TV.
You can delete operator profile you added.
your CAM will inform you and guide you through the
Operator Profile installation.
When operator's profile is added by the CAM, it will
be displayed in the CH list menu. Each profile will be
stored as an independent list in the TV.
You can delete operator profile you added.
Go to “TV Menu” > “Setup” > “View setting” >
“Channel settings” > “Programme setup” >
“Operator profile management”.
“Channel settings” > “Programme setup” >
“Operator profile management”.
NOTE
• The TV supports 2 operator profiles.
• Operator profile can have mixed services such as T/C/
• Operator profile can have mixed services such as T/C/
S1/S2/S3/S4, but will only be displayed based on the
network and media type you select.
network and media type you select.
Watching TV
Click on the first or last page to see other LC-60UD20KN (serv.man5) service manuals if exist.