DOWNLOAD Sharp LC-60UD20KN (serv.man5) Service Manual ↓ Size: 9.11 MB | Pages: 89 in PDF or view online for FREE

Follow the steps below one by one when using the TV. Some steps may not be necessary 
depending on your TV installation and connection.

•  The cable tie can be moved from 

 to 

.

•  Place the TV close to the AC 

outlet, and keep the power 
plug within reach.

•  Product shape varies in some 

countries.

 

n

Plug the standard DIN45325 plug (IEC 169-2) 
75 

q coaxial cable.

 

o

Connect the satellite antenna cable.

 

p

Insert a CA card into the CI slot to watch scrambled 
broadcasts (Page 9).

 

q

Plug in the AC cord.

 

n

Press 

a on the TV (Page 16).

 

o

Run the initial auto installation (Page 12).

 

w Language setting

 

w Home/Store setting

 

w Country setting

 

w PIN setting

 

w Channel search setting

• Digital search

 

− Terrestrial

 

− Cable

• Analogue search
• Satellite search

 

p

Now you can watch TV.
•  If necessary, adjust the antenna to attain maximum signal 

reception (Page 15).

•  You can turn on/off the 

power using both the 
remote control and the 
TV.

•  You can also select a 

channel from “HOME” > 
“CH list”.

_21)

_52)

_32)

•  Be sure to turn off the TV and 

any devices before making any 
connections.

_56)

_61)

_64)

*  The following service is now 

available:

•  YouTube™ (Page 10)
•  Net TV (Pages 62–64)

_74)

•  Some menu items are greyed 

out in 3D mode. This is not a 
malfunction.

_48)

•  You can launch Internet 

connection and Home 
network functions, as 
well as perform settings 
for the TV from the 
“HOME” screen.

•  It takes a few minutes to certify the licence key when 

you insert a CA card into the CI+ compatible CI module 
for the first time. This process may fail when there is no 
antenna input or you have never run “Auto installation”.

•  The CI+ compatible CI module sometimes upgrades its 

firmware. You may not receive any TV images before 
upgrading. You can only use the power button during 
upgrading.

•  Copy protected content may not be output or may be 

output with a copy control signal. The protect icon* is 
displayed when P.INFO is pressed while watching copy 
protected contents.

* Protect icon: 

X

•  If the TV displays an update confirmation message for 

the CA card while receiving CI+ compatible broadcasts, 
follow the screen prompts.

•  Make sure that the CI module is properly inserted.
•  If the old CAM is used, authentication may fail. In such 

cases, contact the contracted service provider.

When a CAM PIN code is required for recording a 
programme, it is necessary to enter the CAM PIN 
code in advance.

 

Go to “TV Menu” > “Setup” > “Option” > 
“CI setting” > “Recording CAM PIN setting”.

 

Enter the CAM PIN code.

•  If a PIN code is not entered or is entered incorrectly, the 

programme will not be able to be recorded/played back.

CI Plus is an advanced development of the DVB 
Common Interface Standard.

 

Regarding security

There are some regulations in recording functions.
The playback of encrypted programmes is 
strongly dependent on which CA module is 
used. The playback of encrypted recordings may 
sometimes not be possible, or only during limited 
time. Programme providers, who use the CI Plus 
standard, can assign different rights for their 
broadcast programmes. 
Exercise caution when using USB-recording to 
record broadcast programmes (Pages 49–52).

 

Operator service list management (Operator 
profile)

Under the 1.3 specification the CAM may provide 
the channel listing parameters (channel number, 
frequency etc.) and these can be updated while in 
use.
Refer to “Operator profile” on page 18.

In order to receive coded digital stations, a common 
interface module (CI module) and a CA card must be 
inserted in the CI slot of the TV.

 

Carefully insert the CI module in the CI slot with 
the contact side forward.

 

The logo on the CI module must be facing 
outward from the rear of the TV.

Go to “TV Menu” > “Setup” > “Option” > 
“CI setting” > “CI menu”.

•  This menu is only available for digital stations.
•  The content of this menu depends on the provider 

of the CI module.

General information on CI module displays.

Adjustment parameters of each CA card displays.

You can input numerical values such as passwords 
here.

You can easily launch this “HOME” screen to enjoy Internet connection and 
Home network functions and to perform settings for the TV.

1 Display the HOME screen

Press 

 (HOME) and the “HOME” screen will be displayed.

2 Select an item

Press 

a/b/c/d to select the desired service or menu, and then press ;.

See the right column for details on the operations in the “HOME” screen.

3 Exit the HOME screen

The operation will exit the “HOME” screen if you press 

 (HOME) before it is 

completed.

This product is embedded with LC Font technology, which was developed 
by SHARP Corporation for clearly displaying easy-to-read characters on LCD 
screens.

Main information 

display zone

Featured and 

recommended 

function zone

Other function icons

Main information display zone
Various information, including the time, currently displayed programming, and current 
setting status are shown. Switching between the current setting status can be done 
using the coloured buttons.

Featured and recommended function zone
Available and recommended functions are shown.

Other function icons
Other function icons are shown.

In this manual, the following expression is often used in order to simplify 
instructions.

•  Go to “TV Menu” > “Setup” > ...

This indicates how to navigate through the Menu screen using the 

a/b/c/d 

and

 ; buttons.