DOWNLOAD Sharp LC-60UD20KN (serv.man5) Service Manual ↓ Size: 9.11 MB | Pages: 89 in PDF or view online for FREE

Press R button.

When the service is locked, you must enter your 
PIN whenever you tune to the service.

Press G button.

Services with a ✔ mark are passed over when 
pressing 

:r/s on the TV or remote control 

unit.

Press Y button.

The selected service is deleted. If you want 
to watch the service you deleted once again, 
perform “Auto installation”, “Additional search”, 
or “Manual search”.

Press B button.

The item position of services can be sorted.

 

1

Press 

a/b to select the service whose 

item position you want to move, and then 
press 

;.

 

2

Press 

a/b to move it to the desired 

position, and then press 

;.

 

3

Repeat steps 1 and 2 until all desired 
service items are sorted.

E

When the country setting is “Norway” and DTV, 
the user may select their preferred network. The 
service sorting will be changed in accordance with 
the preferred network. If a conflict occurs between 
multiple networks, this function allows you to select 
your preferred network.

 

Press 

a/b to select the desired network.

 

Press 

; to set the network selected.

You can reconfigure the following settings when you 
select “Cable” in the initial auto installation or the 
“Auto installation” menu.

E

Use this menu to add new services automatically 
after “Digital search” in the “Auto installation” 
menu has been completed. Follow steps 1 to 5 in 
Searching for cable broadcasts on page 13.

E

Normal: Add new services within a specified 

frequency band. After setting the items 
on the following screen, the TV starts 
searching.

Special: Use this option only when no channels can 

be found by "Normal".

•  Refer to the table about menu items in the centre 

column on page 13.

Frequency

Symbol rate

QAM modulation

Search start

MHz

E

This function is the same as in “Terrestrial”. Refer to 
“Manual adjust” in “Terrestrial”.

•  Some functions may not display or be selectable 

depending on the country setting or cable provider 
selection.

Before selecting the type of search in “Satellite 
setting”, you need to select the satellite broadcast.

SAT2 [Hot Bird 13E]

SAT3 [None]

SAT4 [Turksat]

E

Use this menu to add new services automatically 
after auto installation has been completed. Follow 
steps 1 to 2 in the right column on page 14.

E

Normal: Add new services within a specified 

frequency band. After setting the items 
on the following screen, select “Yes” from 
“Search start” menu.

Special: Use this option only when no channels can 

be found by "Normal".

Band

[Vert/Low]

Frequency
Symbol rate
Search start

Vert/High

Horiz/Low

Horiz/High

Vert/Low

E

This function is the same as in “Digital setting”. 
Refer to “Manual adjust” in “Digital setting”.

You can reconfigure the analogue TV channels 
settings automatically or manually.

E

Use this menu to add new services automatically 
after “Analogue search” in the “Auto installation” 
menu has been completed.

•  Start searching channels after selecting the colour 

system and sound system.

E

Use this menu to set up analogue TV channels 
manually.

After selecting “Yes” on the screen, press 
a/b/c/d to select the channel you want to 
set and then press 

;.

You can adjust the frequency to the desired position.

•  Adjust while checking the background picture as a 

reference.

•  You can set by directly entering the frequency number 

of the channel with 0

_9 numeric buttons.

•  179.25 MHz: Press 1 > 7 > 9 > 2 > 5.
•  49.25 MHz: Press 4 > 9 > 2 > 5 > 

;.

Select the optimum colour system to receive 
(“Auto”, “PAL”, “SECAM”).

Select the optimum sound systems (broadcasting 
systems) to receive (“B/G”, “D/K”, “I”, “L/L’”).

When a TV channel sends its network name, the 
“Auto installation” detects the information and 
assigns a name to it. However, you can change 
channel names individually.

Select each character of the new name for the 
channel with using the software keyboard (Page 11).

•  The name can be five characters or less.

Channels with “Skip” set to “On” are passed over 
when using 

:r/s even if selected while watching 

the image from the TV.

You can block the viewing of any channel.

•  See “PIN” for setting a PIN.
•  When “Lock” is set to “On” for a channel, “Child lock 

has been activated” displays, and the image and sound 
of the channel are blocked.

• When pressing 

6 while “Child lock has been activated” 

displays, the PIN input window will display. Inputting 
the correct PIN unlocks the “PIN” temporarily until the 
power is turned off.

E

Channel positions can be sorted freely.

 

Press 

c/d to select “Yes”, and then press ;.

 

Press 

a/b/c/d to select the channel you 

want to move, and then press 

;.

 

Press 

a/b/c/d to move it to the desired 

position, and then press 

;.

 

Repeat steps 2 and 3 until all desired channels 
are sorted.

E

Channels can be erased individually.

 

Press 

c/d to select “Yes”, and then press ;.

 

Press 

a/b/c/d to select the channel you 

want to erase, and then press 

;.

•  A message window pops up.

 

Press 

c/d to select “Yes”, and then press 

; to erase the selected channel. All the 
subsequent channels move up.

 

Repeat steps 2 and 3 until all desired channels 
are erased.

Allows you to use a PIN to protect certain settings 
from being accidentally changed.

Go to “TV Menu” > “Setup” > “View setting” > 
“Individual setting” > “PIN”.

•  PIN input is required when executing “PIN”. The default 

PIN is “1234”. To reset the PIN setting (PIN input will no 
longer be needed), refer to Reset the PIN (Page 76).

E

Register a four-digit number to use the “PIN” 
function.

 

Press 

c/d to select “Yes”, and then press ;.

 

Enter the four-digit number as a PIN using 0

_9 

numeric buttons.

 

Enter the same four-digit number as in step 2 to 
confirm.

•  “The system PIN has been changed successfully” 

displays.

 

Press 

;.

•  As a precautionary measure, make a note of your 

•  “0000” cannot be set as the PIN code.
•  To view a locked channel, you must enter the PIN (see 

pages 39 and 40 for locking channels from viewing in DTV, 
SAT and ATV mode). When you select a locked channel, 
a PIN prompt message pops up. Press 

6 to display the 

PIN input window.

This function allows DTV services to be restricted. 
It prevents children from watching violent or sexual 
scenes that may be harmful.

 

Go to “TV Menu” > “Setup” > “View setting” > 
“Individual setting” > “Parental rating”.

 

Repeat steps 1 to 4 in when selecting “Yes” to 
the left.

•  “Universal viewing” and “Parental approval pref.” are 

ratings used exclusively in France.

•  Refer to page 84 for details about ratings.

You can adjust the time manually and change the 
clock display.

Go to “TV Menu” > “Setup” > “View setting” > 
“Individual setting” > “Clock setup”.

This function allows you to set the clock manually.

•  If you select “No”, the TV will try to get the time for the 

broadcast.

This function allows you to display the clock time in 
the lower-right corner of the screen.

Displays the clock time.

Displays the clock time in 
30-minute increments.

Hides the clock time.

You can select the time format (either “24HR” or 
“AM/PM”) for the clock time.

You can select the type of the clock (either “Digital” 
or “Analogue”) displayed in the lower right of the 
screen.

•  This setting does not influence the clock displayed on 

the HOME screen.

Set up to three preferred multi audio languages to 
display if the audio languages are available.

Go to “TV Menu” > “Setup” > “View setting” > 
“Individual setting” > “Digital audio language”.

E

Each time you press 

7 on the remote control unit, 

the audio language switches.

Set up to two preferred subtitle languages (including 
subtitles for the hearing impaired) to display if 
subtitles are available.

Go to “TV Menu” > “Setup” > “View setting” > 
“Individual setting” > “Subtitle”.

 

E

 

E

 

E

E

Each time you press 

[ on the remote control unit, 

the subtitle switches.

E

Subtitles for the hearing impaired have priority over 
each of the subtitle language settings (e.g., “1st 
language”, “2nd language”, etc.).

•  Subtitles will not be displayed when the programme 

does not contain subtitle information.

•  Subtitles may not be displayed properly in 3D mode.

You can select an OSD language from among 30 
languages. Refer to the OSD language column in 
the specification table for the selectable languages 
(Page 81).

Go to “TV Menu” > “Setup” > “View setting” > 
“Language”.