Sharp LC-60LE636E (serv.man12) User Manual / Operation Manual ▷ View online
63
Disclaimers and software licences for Net TV
DISCLAIMERS
•
•
•
•
•
•
This product includes the Opera™
browser.
• This product contains fonts provided by Monotype Imaging Inc.
• Monotype® is a trademark of Monotype Imaging Inc. registered in the United States
Patent and Trademark Office and may be registered in certain jurisdictions.
• Tioga™ is a trademark of Monotype Imaging Inc. and may be registered in certain
jurisdictions.
• Letter Gothic™ is a trademark of The Monotype Corp. and may be registered in
certain jurisdictions.
• iType® is a trademark of Monotype Imaging Inc. registered in the United States
Patent and Trademark Office and may be registered in certain jurisdictions.
• This product contains the iType® font engine from Monotype Imaging Inc.
Net TV
64
Appendix
Troubleshooting
Problem
Possible solution
• No power.
• Is the AC cord disconnected?
• Check if you pressed < on the TV.
• The TV cannot be
operated.
• External influences such as lightning, static electricity, etc.,
may cause improper operation. In this case, operate the TV
after first turning off the power, or unplugging the AC cord
and re-plugging it in after one or two minutes.
• Remote control unit
does not operate.
• Are batteries inserted with polarity (e, f) aligned?
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminating to the remote control
sensor?
• Picture is cut off.
• Is the image position correct?
• Are screen mode adjustments (Wide mode) such as picture
size made correctly? (Pages 41, 53 and 54)
• Strange colour,
light colour, or dark
colour, or colour
misalignment.
• Adjust the picture tone.
• Is the room too bright? The picture may look dark in a room
that is too bright.
• Check the “Colour system” setting (Pages 38 and 43).
• Power is suddenly
turned off.
• The TV’s internal temperature has increased. Remove any
objects blocking the vent or clean.
• Is the “Sleep timer” set? Select “Off” from the “Sleep timer”
menu (Page 35).
• Is “No signal off” or “No operation off” activated? (Page 35)
• No picture.
• Are connections to external equipment correct?
(Pages 24_29)
• Is the input signal type selected correctly after connection?
(Page 43)
• Is the correct input source selected? (Page 19)
• Is a non-compatible signal being input? (Page 56)
• Is the picture adjustment correct? (Pages 32_33)
• Is the antenna connected properly? (Page 9)
• Is “On” selected in “Audio only”? (Page 35)
• No sound.
• Is the volume too low?
• If you do not clearly hear the sound for the visually
impaired, go to “Menu” > “Setup” > “Audio” > “Audio
description setting” > “Mix level”, and select the upper level
to turn up the volume.
• Make sure that headphones are not connected.
• Check if you pressed e on the remote control unit.
• No sound. (continued) • Is the proper item selected in the “Audio select” menu
when connecting devices to the HDMI 2 terminal or the PC
terminal? (Pages 25, 27 and 42)
• The TV sometimes
makes a cracking
sound.
• This is not a malfunction. This happens when the cabinet
slightly expands and contracts according to changes in
temperature. This does not affect the TV’s performance.
Reset the PIN
1
Go to “Menu” > “Setup”.
2
Press a/b to select “Auto installation”, “Programme setup”, “PIN”,
“Parental rating” or “Reset”, and then press ;. The PIN input window will
display.
3
Press and hold both !r and Yk on the TV simultaneously until the
message appears on the screen.
NOTE
• When the PIN code is reset, the default PIN code (“1234”) is set.
• The PIN is also available for the Net TV function.
Reset
If complex adjustments are made so that the settings cannot be restored to
normal, you can reset the settings to the factory preset values.
1
Go to “Menu” > “Setup” > “View setting” > “Reset”.
2
Press c/d to select “Yes”, and then press ;.
• “Now, TV will restart automatically, OK?” displays on the screen.
3
Press c/d to select “Yes”, and then press ;.
• “Now initialising...” displays on the screen and blinks.
• After the reset has completed, the power shuts off and then comes back on. The
screen will have returned to its original settings.
NOTE
• PIN input is required when executing “Reset”. The default PIN is “1234”. To change the
PIN setting, refer to Individual setting - PIN (Page 39). To reset the PIN setting (PIN input
will no longer be needed), refer to Reset the PIN shown above.
65
Updating your TV via DVB-T/T2*
Ensure that your TV software version is always up to
date. From time to time SHARP will make updated
TV base software and DVB software available.
* 636 series only
View setting
Download setup
Go to “Menu” > “Setup” > “View setting” >
“Individual setting” > “Standby search” >
“Download setup”.
Searching for updates*
* All countries except UK, Sweden and Italy are set to
“No” for this function.
The TV automatically determines whether a new
software version is available when the TV is in
standby mode.
Item
Yes
Automatically searches for new
software updates available when the
TV is in standby mode.
No
Does not search for update
information.
Now
Checks if there is new software
immediately.
Downloading the software
You can select the method of update.
1
If the software is updated, the confirmation
message “New download information has been
detected.” appears.
• If the TV receives the update service while in
standby mode, a confirmation message displays
after turning on the power.
2
Follow the screen prompts.
Item
Yes
Starts downloading immediately.
It takes approximately one hour to
update. You cannot carry out other
operations while downloading.
• Cancels the download by pressing
; on the remote control unit when
“Discontinue” is displayed on the
screen during the update.
No
Starts downloading automatically
several minutes after entering standby
mode.
NOTE
• Updating the software may take some time.
Getting update information
Information
Message list
When new software is detected, you can confirm the
update information and download the software from
“Message list”.
Go to “Menu” > “Setup” > “Information” >
“Message list”.
NOTE
• When the TV succeeds at downloading new software,
the message is updated in the “Message list” of the
“Information” menu.
• The software update will not be carried out if there is no
new software available at the specified download time.
Information
Receiver report
Display reports regarding failures and changes for
timer settings.
Go to “Menu” > “Setup” > “Information” >
“Receiver report”.
Information
Identification
You can check the TV ID on the screen for reporting
to customer service.
Go to “Menu” > “Setup” > “Information” >
“Identification”.
Appendix
66
Information on the software licence
for this product
for this product
Information
Software licence
You can read the software licences in this menu.
Go to “Menu” > “Setup” > “Information” >
“Software licence”.
E
Software composition
The software included in this product is comprised
of various software components whose individual
copyrights are held by SHARP or by third parties.
Updating your TV via USB/network
Information
Software update
This function allows you to update to the latest
software via a USB device or network.
• To check the availability of the latest software versions,
visit http://www.sharp.eu/software-download/ for links
to the download pages for the appropriate countries.
1
Go to “Menu” > “Setup” > “Information” >
“Software update” > “USB update”.
• You can also update the software through the
network. Go to “Menu” > “Setup” > “Information” >
“Software update” > “Network update” and follow
the on-screen instruction.
• A broadband connection and Network setup are
required to update the software using the internet
(Pages 59–60).
2
Press ; and then insert the USB device
containing the software update file.
CAUTION
• Be sure to insert the USB device correctly into the
terminal.
3
Press > to close the window when a screen
prompt pops up.
4
The TV displays a confirmation screen while
checking the data in the inserted USB device.
CAUTION
• If the data is not compatible with the system, an error
message appears on the screen. Repeat steps 2 and 3
after pressing ;.
• When an error message displays, check to see if:
• The USB device is inserted firmly.
• The USB memory has two or more software update
files.
• No data for updating the system exists in the USB
memory.
• The software update file is broken.
• The software update file is not compatible with your
TV’s software.
• The current system is same as the system update
data.
5
The TV displays the software version information
after checking the data.
6
Press c/d to select “Yes” to update the
system, and then press ;.
7
The TV restarts automatically, and the software
update will be complete.
• This operation may take a while.
Appendix
Click on the first or last page to see other LC-60LE636E (serv.man12) service manuals if exist.