Sharp LC-60LE636E (serv.man12) User Manual / Operation Manual ▷ View online
47
Time shift
This function enables you to pause the digital TV
or satellite programme you are watching and start
watching it again from the paused scene.
1
Press READY.
• The TV starts temporary recording of the real time
broadcast in the background.
2
Press I.
• The TV shows the programme from the scene that
the TV started recording and the recording carries
on.
• When the TV again playbacks after once pressing
H
to stop the programme, the TV shows the
programme from the stopped scene.
Buttons for time shift operation
Buttons
Description
READY
Start recording the programme you are
watching.
• You cannot playback the recorded
programme until approximately three
seconds after pressing READY to
start recording.
I
Playback the recorded programme.
H
Stop the programme in playback (time
shift recording continues) and go back
to the real time broadcast (live).
F
Pause the programme in playback
(time shift recording continues).
• This function is released in 15
minutes.
S
Reverse (each time you press this
button, the reverse speed changes in
three levels).
J
Fast forward (each time you press this
button, the fast forward speed changes
in three levels).
a
Playback after jumping backwards by
10 seconds.
b
Playback after jumping forward by 30
seconds.
CONTROL*
1
Activate the control panel.
c*
2
Playback will resume after jumping
backwards by the time interval you set
in “Jump time setting” (Page 48).
d*
2
Playback will resume after jumping
forward by the time interval you set in
“Jump time setting” (Page 48).
I
The CONTROL button is only available on the remote
control unit.
J
The c and d buttons are only available on the
control panel.
NOTE
• Instead of pressing buttons on the remote control
unit, most of the operations shown to the left are also
available on the screen with the control panel. You can
call up this control panel by pressing CONTROL on the
remote control unit or select “Control (Time shift)” from
“Option” > “Option for view”.
• The control panel for time shift displays only during time
shift operation.
• The “Audio description setting” menu does not work
during time shift playback.
• When the amount of memory used for time shift reaches
“Full” and the blue point is around the left edge of the
bar (see
and
in the Counter section on page 48),
you cannot operate some functions (F (Pause), S
(Reverse), a (Jumping backwards by 10 seconds),
c
c
(Jumping backwards by the time interval you set in
“Jump time setting” (Page 48)).
• Time shift recording stops if no operation detected for
three hours.
• Time shift does not work for ATV, external inputs, data
broadcasts and radio broadcasts.
• To release time shift, press READY, change the DTV/
SAT channel, change “INPUT” or turn off the power of
the TV.
• Time shift will be released if no operations are
performed for three hours.
• Some functions do not work during time shift.
• Time shift is not actually a recording function, so the
recorded data is reset when you exit time shift.
• Time shift does not work automatically, it starts only
when you press READY.
• The PIN is required when you use the buttons such as
S
, J, a, b, c, d if you set the PIN and
any options for “Parental rating” except “None” are
selected.
• Time shift does not work for any copy protected
programmes.
• For certain signals, resolution may be reduced during
time shift playback.
• Do not disconnect the USB storage device used for
time shift during time shift operation.
Other useful features
48
Examples of time shift usage
When you move away from the TV for a while
(press READY when you move away from
the TV)
(press READY when you move away from
the TV)
Without time shift
Away
You miss the scene while you are away.
With time shift
Away
You can watch the missed scene when you come back.
When you want to watch the same scene
again (you must press READY in advance for
time shift to function)
again (you must press READY in advance for
time shift to function)
Without time shift
You cannot watch the same scene again.
With time shift
You can watch the same scene again.
Display information regarding time shift
Channel display
Channel information displays by pressing p on the
remote control unit.
Audio (ENG)
STEREO
Video
Subtitle
Subtitle
Off
>> New information
The time shift ready icon shows up when
READY
READY
is pressed and the TV is recording the
programme.
The status icon shows up depending on what
is shown on the screen.
Counter
The counter displays when you set “On” in “Display the
Time shift memory” (Go to “Setup” > “Option” > “Time
shift setting”).
Time shift
Memory used:
Memory used:
The grey bar shows how much memory is in
use.
This blue point shows how much time has
progressed.
“FULL” shows up when the grey bar reaches
the right edge. The TV starts overwriting the
previously recorded data.
NOTE
• You can also call up the information above by pressing
CONTROL
on the remote control unit or select “Control
(Time shift)” from “Option” > “Option for view”.
Option
Auto input selection
You can choose whether or not to switch the input
source automatically when receiving an AQUOS
LINK or an Euro SCART compatible signal on the TV
during time shift operations.
Go to “Menu” > “Setup” > “Option” > “Time shift
setting” > “Auto input selection”.
Item
Enable
Release time shift when receiving
an AQUOS LINK or a Euro SCART
compatible signal. Switch input source
automatically.
Disable
Time shift continues to work. The
TV does not switch input source
automatically even when receiving
an AQUOS LINK or a Euro SCART
compatible signal.
Option
Jump time setting
You can set the time interval for playback to resume
after jumping backwards/forward.
Go to “Menu” > “Setup” > “Option” >”Time shift
setting” > “Jump time setting”.
• A time interval from 1 to 99 minutes can be
selected.
NOTE
• You can use the time interval you set using the c or
d
buttons on the control panel.
Other useful features
49
Option
Device registration
You need to perform this function to register the
USB storage device for the time shift.
Go to “Menu” > “Setup” > “Option” >“Time shift
setting” > “Device registration”.
• Refer to For time shift (Page 46) for registering a
USB storage device.
NOTE
• Only one USB storage device can be registered for time
shift. Remove all USB storage devices except the one
used for time shift.
• At least 1 GB is required for a USB storage device for
time shift.
• A USB HDD cannot be used as a USB storage device
for time shift.
• Some USB storage devices, such as ones which have
multiple drives, etc., cannot be used for time shift.
Option
Device check
You can manually check the condition of a USB
storage device to be used for time shifting.
Go to “Menu” > “Setup” > “Option” > “Time shift
setting” > “Device check” > select “Yes”.
NOTE
• This menu item cannot be selected when a USB storage
device for time shift is not registered.
Other useful features
50
USB media/Home network
USB media/Home network
In both modes, you can enjoy viewing photos,
listening to music and watching videos from external
USB devices (USB Memory, USB card reader (Mass
Storage Class), USB HDD) or Home network server.
NOTE
• To connect a Home network server, refer to Network setup (Page 59).
• Some USB devices may not work properly for this function.
• The corresponding file format is different between “USB
media” and “Home network”.
• “Wide mode” is fixed during “Photo mode”. During
“Video mode”, you can select “Auto” or “Original”.
• Depending on the Home network server, the TV may not
be able to recognise the contained data.
• Use only alphanumeric characters for naming files.
• Do not disconnect a Home network server from the TV
while transferring files, using the slide show function,
when a screen is switching to another or before you exit
“Home network” from the “INPUT” menu.
• Do not connect and disconnect a Home network server
from the TV repeatedly.
Selecting the mode
Common operation
Select “USB media” or “Home network” from the
“INPUT” menu to enter this mode.
Another way to select the mode
• USB media
Select the USB media mode option on the screen when
a USB device is connected to the TV.
Selecting modes and drives/servers
1
Press B.
When the USB media menu is displayed
1 Press a/b to select “Select USB drive”, and then press ;.
• The available selections are “Select USB drive”
and “Folder display setting”.
2 Press a/b/c/d to select the USB device where
you want to find your files, and then press ;.
• You can select from “All” or “Folder” for the type
of folder directory in “Folder display setting”.
When the Home network menu is displayed
Press a/b to select the Home network server where
you want to find your files, and then press ;.
• Press Y to search for servers.
2
Press c/d to select among “Photo mode”,
“Music mode” or “Video mode”, and then press
;.
Photo mode
Video mode
Music mode
NOTE
• The explanations for the buttons that can be used in each
mode are the explanations when using USB media mode.
Some operations may differ in Home network mode. Follow
the guide display during operations.
• You do not need to select the drive/server in step 1 when there
is only one drive in the connected USB device or there is only
one Home network server connected to the TV.
• 16 is the maximum number of drives that can be
displayed in USB media mode.
• 10 is the maximum number of servers that can be
displayed in Home network mode.
• You cannot enter these modes when there is no server
connected to the TV in Home network mode.
Photo mode
Viewing thumbnails
* This screen image is for the USB media mode. It
may be slightly different in the Home network mode.
Buttons for thumbnail operations
(When using USB media mode)
(When using USB media mode)
Buttons
Description
;
When selecting a folder icon: Enter this
directory.
When selecting a photo thumbnail:
Enlarge the photo.
a/b/c/d
(Cursor)
(Cursor)
Select a desired item.
6
Return to the previous operation.
R button
Select/deselect items (✔ mark appears
on the selected items).
G button
All*: Select BGM for the slide show.
Folder*: Move to the parent folder.
Y button
Start the slide show.
B button
Display “USB media menu”.
• Select slide show interval
• Select slide show BGM
• Set all slide show image
• Reset all slide show image
• USB device removal
* The mode selected in “Folder display setting”
NOTE
• When there are invalid photo files, the g mark will be
displayed for the file.
• You can see the file name, shooting date, file size and
pixel size of the selected photo on the left of the screen
(shooting date is only available in the EXIF file format).
Other useful features
Click on the first or last page to see other LC-60LE636E (serv.man12) service manuals if exist.