Sharp LC-60LE636E (serv.man12) User Manual / Operation Manual ▷ View online
35
Power save settings
Go to “Menu” > “Setup” > “ECO”.
Setup
No signal off
ECO picture control
ECO
Energy save
CH list
:Back
:Enter
Menu
No operation off
[Disable]
[Disable]
[Off]
[On]
ECO
ECO picture control
This function automatically detects the image
source and decreases the power consumption while
keeping the brightness of the image unchanged.
NOTE
• This function does not work when “AV mode” is set to
“DYNAMIC (Fixed)”, “DYNAMIC” or “AUTO”.
• This function does not work when “Energy save” is set
to “Standard” or “Advanced”.
ECO
Energy save
This function enables you to reduce the backlight
brightness in order to decrease the power
consumption and increase the backlight life span as
shown in the following table.
Item
Standard
Reduces the backlight brightness.
Advanced
Reduces the backlight brightness more
than “Standard”.
Off
The backlight brightness is the same
value of your settings in the selected
“AV mode”.
NOTE
• This function does not work when “AV mode” is set to
“DYNAMIC (Fixed)”.
E
“Energy save” status icons
Icon
Description
“Energy save” is set to “Standard”.
“Energy save” is set to “Advanced”.
When “Energy save” is set to “Standard” or
“Advanced”, “Energy save” status icons appear
in the “Picture” menu and channel information
windows.
ECO
No signal off
When set to “Enable”, the TV will automatically
enter standby mode if there is no signal input for 15
minutes.
NOTE
• Even if a TV programme finishes, this function may not
operate because of interference from other TV stations
or other signals.
ECO
No operation off
The TV will automatically enter standby mode if no
operations are performed in three hours if “Enable”
is selected.
NOTE
• Five minutes before the TV enters standby mode, the
remaining time displays every minute.
ECO
Sleep timer
Allows you to set a time when the TV automatically
enters standby mode. You can set the time span for
entering standby mode after selecting “Change”.
NOTE
• Select “Off” to cancel the sleep timer.
• When the time has been set, countdown automatically
starts.
• Five minutes before the preset of time expires, the
remaining time displays each minute.
ECO
Audio only
When listening to music from a music programme,
you can set the TV off and enjoy audio only.
Item
On
Audio is output without a screen image.
Off
Both screen images and audio are output.
Basic adjustment
36
View settings
Go to “Menu” > “Setup” > “View setting”
Setup
Quick start
Auto installation
View setting
Channel settings
CH list
:Back
:Enter
Menu
Individual setting
View setting
Auto installation
The TV automatically detects and stores all available
services in your area. This function also allows you
to perform the channel setting for digital, satellite
and analogue individually and reconfigure the
settings after the initial auto installation has been
completed.
1
Go to “Menu” > “Setup” > “View setting” >
“Auto installation”.
2
Press c/d to select “Yes”, and then press ;.
3
Press a/b/c/d to select the desired
language, and then press ;.
NOTE
• PIN input is required when executing “Auto installation”.
The default PIN is “1234”. To change the PIN setting,
refer to Individual setting - PIN (Page 39). To reset the
PIN setting (PIN input will no longer be needed), refer to
Reset the PIN
Reset the PIN
(Page 64).
• You cannot set the Home/Store setting and the country
setting in “Auto installation” in the “Setup” menu. If
you want to reconfigure those settings, automatically
execute initial auto installation after executing “Reset”
from the “Setup” menu.
• The current country setting is displayed on the screen.
4
Press a/b to select the broadcast standard
you want to search, and then press ;.
E
Digital search
After selecting the service you want to search,
either “Terrestrial” or “Cable”, refer to Digital
broadcast setting
broadcast setting
on page 15.
E
Analogue search
The TV searches for, sorts and stores all the
receivable TV stations. Refer to Analogue
broadcast setting
broadcast setting
on page 15.
E
Satellite search
After selecting “Satellite search”, the current
DVB-S/S2 setting screen is displayed. Refer to
the “Satellite search” setting on pages 16_17.
Important information:
Satellite services are only available for the 635 model
series.
NOTE
• After selecting “Next” in the DVB-S/S2 setting screen,
you need to select your preferred satellite broadcast to
start searching.
View setting
Programme setup
You can reconfigure the DTV service settings
automatically or manually.
1
Go to “Menu” > “Setup” > “View setting” >
“Channel settings” > “Programme setup”.
2
Press a/b to select the broadcast standard
you want to reconfigure, and then press ;.
NOTE
• PIN input is required when executing “Programme
setup”. The default PIN is “1234”. To change the PIN
setting, refer to Individual setting - PIN (Page 39).
To reset the PIN setting (PIN input will no longer be
needed), refer to Reset the PIN (Page 64).
Digital setting
Terrestrial
You can reconfigure the following settings when you
select “Terrestrial” in the initial auto installation or
the “Auto installation” menu.
E
Additional search
Use this menu to add new services automatically
after “Digital search” in the “Auto installation” menu
has been completed.
E
Manual search
Add new services within a specified frequency band.
• Enter the frequency using 0_9 numeric buttons.
• You can perform “Manual search” with a service number
only when the five Nordic countries have been selected
in the country setting.
E
Manual adjust
Configure various settings for each service using the
colour (R/G/Y/B) buttons.
Service
no.
Lock
Service
name
Lock
CH skip
Old LCN
CH skip
Sort
Delete
1
Press a/b to select the desired service.
2
Press the colour button on the remote control
unit corresponding with the item you want to
reconfigure.
• The ✔ mark indicates the operation is set to on.
Each time the colour button is pressed, you can
switch the corresponding operation on/off.
Basic adjustment
37
Buttons for “Manual adjust” operation
Lock
Press R button.
When the service is locked, you must enter your
PIN whenever you tune to the service.
CH skip
Press G button.
Services with a ✔ mark are passed over when
pressing :r/s on the TV or remote control
unit.
Delete
Press Y button.
The selected service is deleted. If you want
to watch the service you deleted once again,
perform “Auto installation”, “Additional search”,
or “Manual search”.
Sort
Press B button.
The item position of services can be sorted.
1
Press a/b to select the service whose
item position you want to move, and then
press ;.
2
Press a/b to move it to the desired
position, and then press ;.
3
Repeat steps 1 and 2 until all desired
service items are sorted.
Cable
You can reconfigure the following settings when you
select “Cable” in the initial auto installation or the
“Auto installation” menu.
E
Additional search
Use this menu to add new services automatically
after “Digital search” in the “Auto installation”
menu has been completed. Follow steps 1 to 5 in
Searching for cable broadcasts
Searching for cable broadcasts
on page 15.
E
Manual search
Add new services within a specified frequency band.
After setting the items on the following screen, the
TV starts searching.
• Refer to the table about menu items in the centre
column on page 15.
Frequency
Symbol rate
QAM modulation
Search start
MHz
E
Manual adjust
This function is the same as in “Terrestrial”. Refer to
“Manual adjust” in “Terrestrial”.
NOTE
• Some functions may not display or be selectable
depending on the country setting or cable provider
selection.
Satellite setting (635 series only)
Before selecting the type of search in “Satellite
setting”, you need to select the satellite broadcast.
SAT2 [Hot Bird 13E]
SAT3 [None]
SAT4 [Turksat]
E
Additional search
Use this menu to add new services automatically
after auto installation has been completed. Follow
steps 1 to 6 in the right column on page 17.
E
Manual search
Add new services within a specified frequency band.
After setting the items on the following screen,
select “Yes” from “Search start” menu.
Band
[Vert/Low]
Frequency
Symbol rate
Search start
Symbol rate
Search start
Vert/High
Horiz/Low
Horiz/High
Vert/Low
E
Manual adjust
This function is the same as in “Digital setting”.
Refer to “Manual adjust” in “Digital setting”.
Basic adjustment
38
Analogue setting
You can reconfigure the analogue TV channels
settings automatically or manually.
E
Additional search
Use this menu to add new services automatically
after “Analogue search” in the “Auto installation”
menu has been completed.
• Start searching channels after selecting the colour
system and sound system.
E
Manual adjust
Use this menu to set up analogue TV channels
manually.
After selecting “Yes” on the screen, press
a/b/c/d to select the channel you want to
set and then press ;.
Fine
You can adjust the frequency to the desired position.
NOTE
• Adjust while checking the background picture as a
reference.
• Instead of pressing c/d to adjust the frequency, you
can set by directly entering the frequency number of the
channel with 0_9 numeric buttons.
EXAMPLE
• 179.25 MHz: Press 1 > 7 > 9 > 2 > 5.
• 49.25 MHz: Press 4 > 9 > 2 > 5 > ;.
Colour sys.
Select the optimum colour system to receive
(“Auto”, “PAL”, “SECAM”).
Sound sys.
Select the optimum sound systems (broadcasting
systems) to receive (“B/G”, “D/K”, “I”, “L/L’”).
Label
When a TV channel sends its network name, the
“Auto installation” detects the information and
assigns a name to it. However, you can change
channel names individually.
Select each character of the new name for the
channel with using the software keyboard (Page
13).
NOTE
• The name can be five characters or less.
Skip
Channels with “Skip” set to “On” are passed over
when using :r/s even if selected while watching
the image from the TV.
Lock
You can block the viewing of any channel.
NOTE
• See “PIN” for setting a PIN.
• When “Lock” is set to “On” for a channel, “Child lock
has been activated” displays, and the image and sound
of the channel are blocked.
• When pressing 6 while “Child lock has been activated”
displays, the PIN input window will display. Inputting
the correct PIN unlocks the “PIN” temporarily until the
power is turned off.
E
Sort
Channel positions can be sorted freely.
1
Press c/d to select “Yes”, and then press ;.
2
Press a/b/c/d to select the channel you
want to move, and then press ;.
3
Press a/b/c/d to move it to the desired
position, and then press ;.
4
Repeat steps 2 and 3 until all desired channels
are sorted.
E
Erase programme
Channels can be erased individually.
1
Press c/d to select “Yes”, and then press ;.
2
Press a/b/c/d to select the channel you
want to erase, and then press ;.
• A message window pops up.
3
Press c/d to select “Yes”, and then press
; to erase the selected channel. All the
subsequent channels move up.
4
Repeat steps 2 and 3 until all desired channels
are erased.
Basic adjustment
Click on the first or last page to see other LC-60LE636E (serv.man12) service manuals if exist.