DOWNLOAD Sharp LC-60LE636E (serv.man12) Service Manual ↓ Size: 7.13 MB | Pages: 76 in PDF or view online for FREE

This function enables the screen to be automatically 

adjusted to its best possible condition when the 

analogue terminals of the TV and PC are connected 

with a commercially available DVI/RGB conversion 

cable, etc.

 

Press b to select “PC” from the “INPUT” 

menu, and then press ;.

 

Go to “Menu” > “Setup” > “Option” > “Terminal 

setting” > “PC signal setting” > “Auto sync.”.

•  When “Auto sync.” is successful, “Auto Sync completed 

successfully” displays. If not, “Auto sync.” failed.

•  “Auto sync.” may fail even if “Auto Sync completed 

successfully” displays.

•  “Auto sync.” may fail if the PC image has low resolution, 

has unclear (black) edges, or is moved while executing 

“Auto sync.”.

•  Be sure to connect the PC to the TV and switch it on 

before starting “Auto sync.”.

•  “Auto sync.” can be executed only when inputting 

analogue signals through the PC terminal.

Ordinarily you can easily adjust the picture as 

necessary to change image position using “Auto 

sync.”. In some cases, however, manual adjustment 

is needed to optimise the image.

 

Press b to select “PC” from the “INPUT” 

menu, and then press ;.

 

Go to “Menu” > “Setup” > “Option” > “Terminal 

setting” > “PC signal setting” > “Fine sync.”.

 

Press a/b to select the specific adjustment 

item.

 

Press c/d to adjust the item to the desired 

position.

Centres the image by moving it to the 

left or right.

Centres the image by moving it up or 

down.

Adjusts when the image flickers with 

vertical stripes.

Adjusts when characters have low 

contrast or when the image flickers.

•  For resetting all adjustment items to the factory preset 

values, press a/b to select “Reset”, and then press 

;.

•  “Clock” and “Phase” in the “Fine sync.” menu can be 

adjusted only when inputting analogue signals through 

the PC terminal.

VGA

640 x 480

31.5 kHz

60 Hz

✔

✔

✔

SVGA

800 x 600

37.9 kHz

60 Hz

✔

✔

✔

XGA

1,024 x 768

48.4 kHz

60 Hz

✔

✔

✔

WXGA

1,360 x 768

47.7 kHz

60 Hz

✔

✔

✔

SXGA

1,280 x 

1,024

64.0 kHz

60 Hz

✔

✔

✔

SXGA+

1,400 x 

1,050

65.3 kHz

60 Hz

✔

✔

✔

UXGA

1,600 x 

1,200

75.0 kHz

60 Hz

✔

✔

✔

1080p

1,920 x 

1,080

67.5 kHz

60 Hz

✔

✔

VGA, SVGA, XGA, WXGA, SXGA, SXGA+ and UXGA are registered trademarks 

of International Business Machines Corporation.

•  This TV has only limited PC compatibility, correct operation can only be guaranteed if 

the video card conforms exactly to the VESA 60 Hz standard. Any variations from this 

standard will result in picture distortions.

•  When a programme is set, the TV can be controlled 

from the PC using RS-232C or IP. The input signal (PC/

video) can be selected, the volume can be adjusted and 

various other adjustments and settings can be made, 

enabling automatic programmed playing.

•  Use an RS-232C serial control cable (cross type), 

ETHERNET cable (commercially available) or wireless 

LAN USB adapter for the connections.

•  This operation system should be used by a person who 

is accustomed to using PCs.

LAN

ETHERNET cable (commercially available)

Connect to the TV with the following settings made 

for IP on the PC.

TCP/IP

Set the IP address on the TV 

menu

None (Do not select Telnet 

or SSH)

Set a port number on the TV 

menu (Control port)

When you set your ID and password on the TV 

menu, you need to enter them as soon as you 

connect to the TV.

•  The connection will be cut off when there has been no 

communication for 3 minutes.

 

Go to “Menu” > “Setup” > “View setting” > 

“Network setup” > “IP Control setup” > select 

“Change”.

 

To use IP Control, select “Enable”.

 

Set the device name.

 

Set your login ID and password.

 

Set the port to use with IP Control.

 

Confirm the settings, and then press “OK”.

RS-232C serial control cable (cross type) 

(commercially available)

Set the RS-232C communications settings on the 

PC to match the TV’s communications conditions. 

The TV’s communications settings are as follows:

9,600 bps

8 bits

None

1 bit

None

Send the control commands from the PC via the 

RS-232C connector.

The TV operates according to the received 

command and sends a response message to the 

PC.

Do not send multiple commands at the same time. 

Wait until the PC receives the OK response before 

sending the next command.

Make sure to send “A” with the carriage return and 

confirm that “ERR” returns before operating.

Eight ASCII codes +CR

n

o

p

C1 C2 C3 C4 P1 P2 P3  P4

 



Command four digits: Command. The text of 

four characters.

 



Parameter four digits: Parameter 0_9, blank, ?, 

minus

 



Return code (0DH): ?

Input the parameter values, aligning left, and fill with 

blank(s) for the remainder (be sure that four values 

are input for the parameter).

When the input parameter is not within an adjustable 

range, “ERR” returns (refer to “Response code 

format”).

0

0

5

5

1

0

0

0

0

0

9

0

When “?” is input for some commands, the present 

setting value responds.

?

?

?

?

Normal response

Problem response 

(communication error or 

incorrect command)

O

K

E

R

R

Return code (0DH)

Return code (0DH)

CONTROL 

ITEM

COMMAND PARAMETER CONTROL CONTENTS

POWER 

SETTING

P O W R 0 _ _ _ POWER OFF 

(STANDBY)

INPUT 

SELECTION A

I

T G D _ _ _ _ INPUT SWITCHING 

(TOGGLE)

I

T V D _ _ _ _ TV (CHANNEL FIXED)

I D T V _ _ _ _ DTV (CHANNEL 

FIXED)

I A V D * _ _ _ EXT 1_3 (1_3), HDMI 

1_4 (4_7), PC (8)

CHANNEL

D C C H *

* _ _ TV DIRECT CHANNEL 

(1_99)

C H U P _ _ _ _ CHANNEL UP
C H D W _ _ _ _ CHANNEL DOWN
D T V D *

*

* _ THREE DIGIT DIRECT 

CHANNEL (1_999) 

(Non-Nordic countries)

D T V D *

*

*

* FOUR DIGIT DIRECT 

CHANNEL (1_9999) 

(Nordic countries 

only)*

1

I D E G _ _ _ _ DIGITAL NETWORK 

CHANGE*

1

D S C 1 *

*

*

* DVB-S/S2 1 DIRECT 

CHANNEL (1_9999)*

1

D S C 2 *

*

*

* DVB-S/S2 2 DIRECT 

CHANNEL (1_9999)*

1

D S C 3 *

*

*

* DVB-S/S2 3 DIRECT 

CHANNEL (1_9999)*

1

D S C 4 *

*

*

* DVB-S/S2 4 DIRECT 

CHANNEL (1_9999)*

1

D T U P _ _ _ _ DTV CHANNEL UP
D T D W _ _ _ _ DTV CHANNEL DOWN

INPUT 

SELECTION B

I N P 1 0 _ _ _ EXT 1 (Y/C)
I N P 1 1 _ _ _ EXT 1 (CVBS)
I N P 1 2 _ _ _ EXT 1 (RGB)

CONTROL 

ITEM

COMMAND PARAMETER CONTROL CONTENTS

AV MODE 

SELECTION

A V M D 0 _ _ _ TOGGLE
A V M D 1 _ _ _ STANDARD
A V M D 2 _ _ _ MOVIE
A V M D 3 _ _ _ GAME
A V M D 4 _ _ _ USER
A V M D 5 _ _ _ DYNAMIC (Fixed)
A V M D 6 _ _ _ DYNAMIC
A V M D 7 _ _ _ PC
A V M D 8 _ _ _ x.v.Colour
A V M D 1 0 0 _ AUTO

VOLUME

V O L M *

* _ _ VOLUME (0_60)

POSITION

H P O S *

*

* _ H-POSITION (AV/PC)

V P O S *

*

* _ V-POSITION (AV/PC)

C L C K *

*

* _ CLOCK (0_180)

P H S E *

* _ _ PHASE (0_40)

WIDE MODE

W I D E 0 _ _ _ TOGGLE (AV)
W I D E 1 _ _ _ NORMAL (AV)
W I D E 2 _ _ _ ZOOM 14:9 (AV)
W I D E 3 _ _ _ PANORAMA (AV)
W I D E 4 _ _ _ FULL (AV)
W I D E 5 _ _ _ CINEMA 16:9 (AV)
W I D E 6 _ _ _ CINEMA 14:9 (AV)
W I D E 7 _ _ _ NORMAL (PC)
W I D E 8 _ _ _ CINEMA (PC)
W I D E 9 _ _ _ FULL (PC)
W I D E 1 0 _ _ DOT by DOT (AV/PC)
W I D E 1 1 _ _ UNDERSCAN (AV)
W I D E 1 2 _ _ AUTO (USB-Video/

Home network-Video)

W I D E 1 3 _ _ ORIGINAL (USB-

Video/Home network-

Video)

MUTE

M U T E 0 _ _ _ TOGGLE
M U T E 1 _ _ _ MUTE
M U T E 2 _ _ _ MUTE OFF

CONTROL 

ITEM

COMMAND PARAMETER CONTROL CONTENTS

SURROUND

A C S U 0 _ _ _ SURROUND TOGGLE
A C S U 1 _ _ _ SURROUND ON
A C S U 2 _ _ _ SURROUND OFF

AUDIO CHANGE A C H A _ _ _ _ TOGGLE
SLEEP TIMER

O F T M 0 _ _ _ OFF
O F T M 1 _ _ _ SLEEP TIMER 30 MIN
O F T M 2 _ _ _ SLEEP TIMER 1 

HOUR

O F T M 3 _ _ _ SLEEP TIMER 1 

HOUR 30 MIN

O F T M 4 _ _ _ SLEEP TIMER 2 

HOUR

O F T M 5 _ _ _ SLEEP TIMER 2 

HOUR 30 MIN

TEXT

T E X T 0 _ _ _ TEXT OFF
T E X T 1 _ _ _ TEXT ON (TOGGLE)

D C P G *

*

* _ DIRECT PAGE JUMP 

(100_899)

DEVICE NAME T V N M 1 _ _ _ DISPLAY THE DEVICE 

NAME

MODEL NAME M N R D 1 _ _ _ DISPLAY THE MODEL 

NAME

SOFTWARE 

VERSION

S W V N 1 _ _ _ DISPLAY THE 

SOFTWARE VERSION

IP PROTOCOL 

VERSION

I P P Y 1 _ _ _ DISPLAY THE IP 

PROTOCOL VERSION

 

I

635 series only