DOWNLOAD Sharp XV-Z7000 (serv.man21) Service Manual ↓ Size: 3.57 MB | Pages: 48 in PDF or view online for FREE

When connecting the projector to a compatible computer other than an IBM-PC (VGA/SVGA/XGA/SXGA) or Mac-
intosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more information.

When connecting this projector to a computer, select “RGB” by using RGB/COMPONENT on the remote control or the GUI
menu. (See page 25.)

• Connecting computers other than the recommended types may result in damage to the projector, the computer, or both.

• This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC compatible

computer will communicate their setting requirements, allowing for quick and easy setup.

• Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last.

• The DDC, Plug and Play function of this projector operates only when used in conjunction with a VESA DDC compatible computer.

RS-232C

INPUT 1

INPUT 2

/COMPONENT

AUDIO INPUT

RGB /COMPONENT

C

R

C

B

Y

(INPUT 1, 2)

You can connect your projector to a computer for projection of full color computer images.

1 Connect one end of the computer RGB cable to the

INPUT 2 RGB/COMPONENT port on the projector.
Secure the connector by tightening the thumb screws.

2 Connect the other end to the Monitor output port on the

computer. Secure the connector by tightening the thumb
screws.

3 To use the built-in audio system, connect one end of

the computer audio cable to the AUDIO INPUT (INPUT
1, 2) terminal on the projector.

4 Connect the other end to the Audio output terminal on

the computer.

• Before connecting, be sure to turn both the projector and the

computer off. After making all connections, turn the projector
on first. The computer should always be turned on last.

• Please read the computer’s operation manual carefully.
• Refer to page 45 “Computer Compatibility Chart” for a list of computer

signals compatible with the projector. Use with computer signals other
than those listed may cause some of the functions not to work.

• A Macintosh adaptor may be required for use with some Macintosh

computers. Contact your nearest Sharp Authorised LCD Projector Dealer
or Service Centre.

When connecting this projector to a computer, select “RGB”
by using RGB/COMPONENT on the remote control or the
GUI menu. (See page 25.)

For Europe only

Computer RGB cable

RS-232C

INPUT 1

/CO

P

B

Y

When the RS-232C port on the projector is connected to a computer with an RS-232C cable (null modem, cross
type, sold separately), the computer can be used to control the projector and check the status of the projector.
See pages 43 and 44 for details.

1 Connect the supplied DIN-D-sub RS-232C cable to the RS-232C port on the projector.

2 Connect an RS-232C cable (null modem, cross type, sold separately) to the other end of DIN-D-sub RS-232C

cable and to the serial port on the computer.

• Do not connect or disconnect an RS-232C cable to or from the computer while it is on. This may damage your computer.

• The RS-232C function may not operate if your computer port is not correctly set up. Please refer to the operation manual of

the computer for details on setting up.

• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Sharp Authorised LCD

Projector Dealer or Service Centre.

DIN-D-sub

RS-232C cable

RS-232C cable

(null modem, cross type, sold separately)

DIN-D-sub RS-232C
cable

1 Make the necessary connections before pro-

ceeding. Connect the power cord to a wall outlet.
The POWER indicator illuminates red and the
projector enters standby mode.

• If the side filter cover is not securely installed, the POWER

indicator flashes.

POWER

LAMP

TEMP.

ON/OFF

KEYSTONE

2 Press ON/OFF on the projector for over one

second, or POWER on the remote control.

• The flashing green LAMP REPLACEMENT indicator shows

that the lamp is warming up. Wait until the indicator stops
flashing before operating the projector.

• If the power is turned off and then immediately turned on

again, it may take a short while before the lamp turns on.

• After the projector is unpacked and turned on for the first

time, a slight odour may be emitted from the exhaust vent.
This odour will soon disappear with use.

• Do not press any buttons before the startup image

disappears. Before “Adjusting The Image” appears, only
ON/OFF or POWER is available.

ON/OFF

POWER

LAMP

TEMP.

KEYSTONE

INPUT

BACK

ENTER

MENU

PICT MODE

VOL

POWER

MUTE

BACK

MENU

ENTER

2

POWER

LAMP

TEMP.

ON/OFF

KEYSTONE

4

3

3 Slide the ZOOM knob. The image can be adjusted

to the desired size within the zoom range.

4 Rotate the FOCUS ring until the image on the

screen becomes clear.

When the power is on, the LAMP REPLACEMENT indicator
lights indicating the status of the lamp.
Green: Lamp is ready.
Flashing green: Warming up.
Red: Change the lamp.

ON/OFF

POWER

LAMP

TEMP.

KEYSTONE

INPUT

BACK

ENTER

MENU

PICT MODE

VOL

POWER

MUTE

BACK

MENU

ENTER

RGB/

COMPONENT

INPUT 1

PICT MODE

AUTO SYNC

INPUT 2

GAMMA

KEYSTONE

VIDEO

FREEZE

S-VIDEO

CLR TEMP

8

5

6

7

8

5 Press INPUT on the projector, INPUT 1, INPUT 2,

S-VIDEO or  VIDEO on the remote control to select
the desired input mode.
Press  INPUT,  INPUT 1,  INPUT 2, S-VIDEO or
VIDEO again to change the mode.

• When the selected input signal is being received, “Adjusting

The Image” will be displayed.

• When no signal is being received, “NO SIGNAL” will be

displayed. When a signal that the projector is not preset to
receive is being received, “NOT REG.” will be displayed.

f

5

d

g

s

6

7

6 Press VOLUME on the remote control to adjust

the volume.

7 Press MUTE on the remote control to temporarily

turn off the sound.
Press MUTE again to turn the sound back on.

8 Press  ON/OFF on the projector for over one

second, or POWER on the remote control.
Press  ON/OFF or POWER again while the
message is displayed.

• If you accidentally pressed ON/OFF or POWER and do not

want to turn off the power, wait until the power off screen
disappears.

• When ON/OFF or POWER is pressed twice, the POWER

indicator will light up red and the cooling fan will run for
about 90 seconds. The projector will then enter standby
mode.

• Wait until the cooling fan stops before disconnecting the

power cord.

• The power can be turned on again by pressing ON/OFF or

POWER. When the power is turned on, the POWER indicator
and the LAMP REPLACEMENT indicator light green.

• The POWER indicator flashes if the right side filter cover is

not securely installed.

WARNING:
The cooling fan in this projector continues to run for about
90 seconds after the projector is turned off. During normal
operation, when turning the power off always use the ON/
OFF button on the projector or the POWER button on the
remote control. Ensure the cooling fan has stopped before
disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE
PROJECTOR OFF BY DISCONNECTING THE POWER
CORD. FAILURE TO OBSERVE THIS WILL RESULT IN
PREMATURE LAMP FAILURE.