Sharp XG-V10WE (serv.man8) Service Manual ▷ View online
37
XG-V10WE
AN-SD1E/S422E
Process menu2
AD
OUTPUT1
OUTPUT2
DTV
OUTPUT3
VIDEO1
VIDEO2
DVD
NOKO
LINE
SSS
PATTERN
CVIC
LENS
SPECIAL
LINE
L1
L2
L3
L4
OFF
TEMP OFF
SENSER CHECK
ID CHECK
IDC
XEGTH
XLTH1-H
XLTH1-L
XLTH2-H
XLTH2-L
YEGTH
YLTH1-H
YLTH1-L
YLTH2-H
YLTH2-L
PROGRESSIVE
MODE
LPF
LSW
PTG
LEVEL
LIMIT
FILM
THRESH
MISSTH
PATTERN
RGB
RGB [50]
CROSS
RAMP
STEP
COLOR
CHR
SSS
TIME
S1
S2
S3
S4
S5
LAMP
SPECIAL
IPL
E2PROM
ADR RD/WR
LENS
LENS AUTO
LENS TOP
LENS BOTTOM
SCREEN
CUBIC-RGB
CUBIC-VIDEO
CVIC
PROGRESSIVE
ENHANCE
SCREEN
IDC
ENHANCE
BBN-RGB
BBN-VIDEO
DFC-RGB
DFC-VIDEO
38
XG-V10WE
AN-SD1E/S422E
Precautions in servicing
(1) If the convergence gets out of spec during servicing, call up the process mode and select the following sub-
jects.
Group
Group
: NOKO
Subject
: R-CNV-H, R-CNV-V
G-CNV-H, G-CNV-V
B-CNV-H, B-CNV-V
B-CNV-H, B-CNV-V
(H: Horizontal adjustment, V: Vertical adjustment)
Adjust the above settings in the range of 0-4. When changing each setting from the initial setting of 2, however,
the 1280 x 1024 dot display area will have a fewer number of lines.
the 1280 x 1024 dot display area will have a fewer number of lines.
Example 1 : When the R-CNV-H setting is changed from 2 (initial) to 4, the number of lines will be from 1280 to
1278.
Example 2 : When the R-CNV-H, G-CNV-H and B-CNV-H settings are changed to 3, 3 and 4, respectively, the
display will be 1278 x 1024 lines. But when the above settings are switched to 2, 2 and 3, respec-
tively, the display will be 1279 x 1024 lines.
tively, the display will be 1279 x 1024 lines.
Preferably keep each setting as close to 2 as possible.
(2) When calling up the process mode, make sure the following appears onscreen.
Group
: VIDEO1
Subject
: SET UP B 2
SET UP C 1
Be sure to exit from this mode with the following onscreen.
Subject
Subject
: SET UP 1
39
XG-V10WE
AN-SD1E/S422E
TROUBLE SHOOTING TABLE
Checking the PWB performance
RGB input in trouble
Feed test pattern signal from
PC.
PC.
Yes
No
Use specified cable.
Is specified cable connected
between PC and projector?
between PC and projector?
Yes
No
Power circuit in trouble.
Is supply voltage as specified?
Yes
No
Check the connectors, starting
from the input circuit.
from the input circuit.
Does image appear?
Video input in trouble
Go to "Checking the video unit
circuit".
circuit".
Through-output in trouble
Through-output circuit in
trouble.
trouble.
Remote control in trouble
Go to "Checking the remote
control".
control".
Go to "Trouble shooting table
for PC I/F unit ".
for PC I/F unit ".
Checking the video system
Yes
No
Go to "Lamp fails to light-up".
Yes
No
Is specified voltage fed to EA
connectors?
connectors?
Check the power circuit and its parts.
Yes
No
Are there signal inputs at pins (12),
(31) and (37) of SC401?
(31) and (37) of SC401?
Are there signal outputs at pins (7) of
IC6014 and (7) of IC6015?
IC6014 and (7) of IC6015?
Check the input unit circuit (IC1401,
IC1402, IC1403, IC1404, IC1405
and its peripheral circuits).
IC1402, IC1403, IC1404, IC1405
and its peripheral circuits).
Yes
Go to "Checking IC803
(RGB signal output circuit)".
(RGB signal output circuit)".
No
Check IC6009, IC6011,
IC6014, IC6015 and their
peripheral circuits as well
as switching circuit.
IC6014, IC6015 and their
peripheral circuits as well
as switching circuit.
Is the lamp on?
40
XG-V10WE
AN-SD1E/S422E
TROUBLE SHOOTING TABLE
(Continued)
Checking the video unit circuit
Yes
No
Check the IC1403, IC1406 selector
switch, terminal voltage and input
circuit.
switch, terminal voltage and input
circuit.
Yes
No
Is there video signal input at IC4001?
Check the low-pass and buffer
circuits of Q4002, Q4003 and Q4004.
circuits of Q4002, Q4003 and Q4004.
Yes
No
Are there signal outputs at pins (6)
and (8) of IC4001?
and (8) of IC4001?
Check IC4001 and its peripheral
circuits (bias).
circuits (bias).
Yes
No
Check the low-pass and buffer circuits
of Q6008 thru Q6014. Is the signal as
specified?
of Q6008 thru Q6014. Is the signal as
specified?
Go to "Checking IC801 (RGB signal
output circuit)".
output circuit)".
Is there video signal output at pin (7)
of IC1405?
of IC1405?
Check Q4005 thru Q4008 and their
peripheral circuits.
peripheral circuits.
Checking IC801 (RGB signal output circuit)
Yes
No
Check the data transfer and other
performance at pins (17) and (18) of
video IC803.
performance at pins (17) and (18) of
video IC803.
No
Go to "No colour or unusual tone",
"No Y signal" or "Out of sync".
"No Y signal" or "Out of sync".
Yes
No
Are there output waveforms at pin
1
of Q6801, Q6802, Q6803?
Check Q6801, Q6802, Q6803 and
their peripheral circuits.
their peripheral circuits.
No
Are there output waveforms at pin
(8), (10), (12) of SC8404?
(8), (10), (12) of SC8404?
Check IC6801, Q6807, Q6808,
Q6809 and their peripheral circuits.
Q6809 and their peripheral circuits.
Yes
Are there RGB output waveforms at
pins (31), (32) and (33) of IC803?
pins (31), (32) and (33) of IC803?
Go to "Trouble shooting table for PC
I/F unit".
I/F unit".
Click on the first or last page to see other XG-V10WE (serv.man8) service manuals if exist.