Sharp MX-TM10 (serv.man3) Service Manual ▷ View online
2
2
2-9
2-9
Technology > Controls > Trimming operation
Technology > Controls > Trimming operation
Trimming operation
The sequence of trimming operation is described below.
1. After registration completes, drive the press motor (M105) and press the booklet with the
press roller. If the booklet is larger than A3, drive the rear estrangement motor and press the
booklet with the paper delivery roller before pressing with the press roller because air must be
released from the leading edge of the booklet (back of the booklet).
2. After pressing the booklet with the press roller, drive the registration motor (M102) and
separate the registration unit from the booklet and then drive the stopper solenoid (SL101) to
lower the registration guide.
3. After the registration guide is lowered, drive the feed motor (M101) and feed the booklet to
the trimming position.
4. When the booklet reaches the trimming position, drive the cutter motor (M106) and trim the
fore edge of the booklet.
At this time, drive the front estrangement motor (M103) to raise the inlet roller (lower) and
drive the registration motor (M102) at the same time to return the registration unit to the home
position.
5. After trimming the booklet, drive the feed motor (M101) and start paper ejection.
6. After feeding for a prescribed distance from the start of ejection operation, drive the rear
estrangement motor (M104) to press the booklet with the eject roller and feed.
7. After the booklet passes the paper delivery sensor (S103), stop the feed motor (M101).
1. After registration completes, drive the press motor (M105) and press the booklet with the
press roller. If the booklet is larger than A3, drive the rear estrangement motor and press the
booklet with the paper delivery roller before pressing with the press roller because air must be
released from the leading edge of the booklet (back of the booklet).
2. After pressing the booklet with the press roller, drive the registration motor (M102) and
separate the registration unit from the booklet and then drive the stopper solenoid (SL101) to
lower the registration guide.
3. After the registration guide is lowered, drive the feed motor (M101) and feed the booklet to
the trimming position.
4. When the booklet reaches the trimming position, drive the cutter motor (M106) and trim the
fore edge of the booklet.
At this time, drive the front estrangement motor (M103) to raise the inlet roller (lower) and
drive the registration motor (M102) at the same time to return the registration unit to the home
position.
5. After trimming the booklet, drive the feed motor (M101) and start paper ejection.
6. After feeding for a prescribed distance from the start of ejection operation, drive the rear
estrangement motor (M104) to press the booklet with the eject roller and feed.
7. After the booklet passes the paper delivery sensor (S103), stop the feed motor (M101).
Trimming blade
F-2-11
2
2
2-10
2-10
Technology > Controls > Servicing Work > Scheduled Servicing
Technology > Controls > Servicing Work > Scheduled Servicing
Servicing Work
■
Scheduled Servicing
When the endurance time of a part expires soon, replace and/or clean it as required.
Item
Part name
Expected
service life
Qty
Operation
Reference
Periodically
replaced parts
None
Consumable
parts
Scratch prevention sheet
(front top)
120,000
sheets
1piece
Replacement
4-11
Scratch prevention sheet
(front bottom/rear bottom)
120,000
sheets
2pieces
Replacement
4-12, 4-12
Cutter unit
50,000
sheets
1piece
Replacement
4-9
Periodically
serviced parts
None
Note:Cutter/Blade life:
50,000 cuts of 5 sheets @ 81.4gm (80gm UK)
plain A4 paper folded = 10 page A5 booklet.
One booklet = one cut
Please be aware that if any media other than 81.4gm (80gm UK)
plain paper or more than 5 x A4 sheets folded are used the life
of the blade will be reduced accordingly.
Example: 20 sheets folded of 81.4gm (80gm UK) will reduce the life
to one quarter of the 50,000 stated above.
If the paper is glossy/coated in any way the life will reduce further.
Life of whole MX-TM10 unit:
1,200,000 x 81.4gm (80gm UK) A4 sheets pass through
This figure is not to be confused with the cutter life.
50,000 cuts of 5 sheets @ 81.4gm (80gm UK)
plain A4 paper folded = 10 page A5 booklet.
One booklet = one cut
Please be aware that if any media other than 81.4gm (80gm UK)
plain paper or more than 5 x A4 sheets folded are used the life
of the blade will be reduced accordingly.
Example: 20 sheets folded of 81.4gm (80gm UK) will reduce the life
to one quarter of the 50,000 stated above.
If the paper is glossy/coated in any way the life will reduce further.
Life of whole MX-TM10 unit:
1,200,000 x 81.4gm (80gm UK) A4 sheets pass through
This figure is not to be confused with the cutter life.
3
3
Maintenance
Maintenance
■
Maintenance List
3
3
3-2
3-2
Maintenance > Maintenance List
Maintenance > Maintenance List
Maintenance List
5
: Check (Clean, replace, or adjust according to necessity.) ¡: Clean p: Replace r: Adjust I: Lubricate
No.
Part name
When calling
When maintenance of the machine
Remarks
1
Paddle solenoid
5
5
Replace at 120K bundles.
2
Discharge needle
5
5
Replace at 120K bundles.
3
Moquette
5
5
Replace at 120K bundles.
4
Cutter unit
5
5
Replace at 50K cut.
5
Trimmer unit
5
5
Replace at 1,200,000 sheets.
Note:Cutter/Blade life:
50,000 cuts of 5 sheets @ 81.4gm (80gm UK)
plain A4 paper folded = 10 page A5 booklet.
One booklet = one cut
Please be aware that if any media other than 81.4gm (80gm UK)
plain paper or more than 5 x A4 sheets folded are used the life
of the blade will be reduced accordingly.
Example: 20 sheets folded of 81.4gm (80gm UK) will reduce the life
to one quarter of the 50,000 stated above.
If the paper is glossy/coated in any way the life will reduce further.
Life of whole MX-TM10 unit:
1,200,000 x 81.4gm (80gm UK) A4 sheets pass through
This figure is not to be confused with the cutter life.
50,000 cuts of 5 sheets @ 81.4gm (80gm UK)
plain A4 paper folded = 10 page A5 booklet.
One booklet = one cut
Please be aware that if any media other than 81.4gm (80gm UK)
plain paper or more than 5 x A4 sheets folded are used the life
of the blade will be reduced accordingly.
Example: 20 sheets folded of 81.4gm (80gm UK) will reduce the life
to one quarter of the 50,000 stated above.
If the paper is glossy/coated in any way the life will reduce further.
Life of whole MX-TM10 unit:
1,200,000 x 81.4gm (80gm UK) A4 sheets pass through
This figure is not to be confused with the cutter life.
Click on the first or last page to see other MX-TM10 (serv.man3) service manuals if exist.