Sharp MX-PE10 FIERY (serv.man2) Service Manual ▷ View online
R
EPLACING
PARTS
76
6 Remove the switch bank assembly from the component sled.
• Remove the three screws that attach the switch bank assembly to the component sled.
• Pull the switch bank assembly straight out of the component sled.
F
IGURE
24:
Removing/replacing the switch bank assembly
N
OTE
:
Guide the cables as you remove the assembly from the component sled. Be careful not
to damage the EMI gasket around the opening in the component sled.
7 If you are removing the switch bank assembly to replace it with a new assembly, remove the
DVD drive (see
page 78
).
Component sled
Switch bank assembly
Screw (1 of 3)
R
EPLACING
PARTS
77
T
O
REPLACE
THE
SWITCH
BANK
ASSEMBLY
1 If it is not already attached, attach the DVD drive to the switch bank assembly
(see
page 79
).
2 Install the switch bank assembly in the component sled (see
Figure 24
).
N
OTE
:
If you are replacing the switch bank assembly with a new one, discard the cable
extensions that may be provided with the new switch bank assembly.
• Starting with the cables, insert the switch bank assembly through the opening in the front
of the component sled. Be sure to fold the EMI gasket under and through the opening
when inserting the assembly.
when inserting the assembly.
• Replace the three screws that secure the switch bank assembly to the component sled.
3 Install the component sled in the chassis (see
Figure 23
).
• Route the cables of the switch bank assembly in through the chassis so that the cables are
within reach of their connectors on the motherboard.
• Slide the sled into the front of the chassis until the guide latches click into place.
N
OTE
:
Be careful not to damage the EMI gasket around the slot in the chassis when installing
the component sled.
4 Connect the following cables (see
Figure on page 50
for the location of connectors on the
motherboard):
• Power and data combination cable
• DVD data cable
• Power button cable
• Reset button cable
• Speaker cable
• Front panel USB port cables
5 Install the ferrite around the two front USB port cables near the motherboard.
Use the ferrite that you removed earlier. Place the ferrite around both cables in between the
two preinstalled tie-wraps, and snap the edges of the ferrite closed.
two preinstalled tie-wraps, and snap the edges of the ferrite closed.
6 Secure the cables with the cable clamp(s) inside the chassis.
7 Reassemble the Fiery Server and verify its functionality (see
page 80
).
R
EPLACING
PARTS
78
DVD drive
The DVD drive is attached to the switch bank assembly. The DVD drive is used to install
system software onto the hard disk drive and archive data onto writable media.
system software onto the hard disk drive and archive data onto writable media.
T
O
REMOVE
THE
DVD
DRIVE
1 Shut down, and then open the Fiery Server (see pages
34
and
37
).
To remove the DVD drive, you must remove the left, right, and front panels, the component
sled, and the switch bank assembly.
sled, and the switch bank assembly.
2 Remove the power and data combination cable from the back of the DVD drive.
3 Remove the component sled from the chassis, and then remove the switch bank assembly
from the component sled (see
page 75
).
4 Remove the four screws that secure the DVD drive to the switch bank assembly.
Set aside the screws so that you can replace them later.
N
OTE
:
On some systems, a small metal post in the switch bank assembly is used in place of
one of the screws.
5 Remove the DVD drive from the switch bank assembly.
F
IGURE
25:
Removing/replacing the DVD drive
Component sled
Switch bank assembly
Screw (1 of 3)
Switch bank assembly
Screw
(1 of 4)
DVD drive
N
OTE
:
Some switch bank assemblies
have a metal post in this location that
is used in place of the screw.
is used in place of the screw.
R
EPLACING
PARTS
79
T
O
REPLACE
THE
DVD
DRIVE
1 Install the DVD drive in the switch bank assembly.
2 Install the switch bank assembly in the component sled, and then install the component sled
in the chassis (see
page 77
).
3 Attach the power and data combination cable to the back of the DVD drive.
4 If you installed a new DVD drive, make sure to reset the time and date in Setup (see
Configure Help for more information).
5 Reassemble the Fiery Server and verify its functionality (see
page 80
).
Click on the first or last page to see other MX-PE10 FIERY (serv.man2) service manuals if exist.