Sharp MX-M950 / MX-MM1100 (serv.man50) User Manual / Operation Manual ▷ View online
49
Loading paper in the bypass tray (MX-MFX2)
1
If you are changing the paper in the
bypass tray, press the release button
and remove the previously used paper.
bypass tray, press the release button
and remove the previously used paper.
The paper table will descend. While the paper tray descends,
the operation button indicator will blink. After the paper tray
finishes descending, the indicator will light solidly.
Do not remove the paper until the indicator turns off.
the operation button indicator will blink. After the paper tray
finishes descending, the indicator will light solidly.
Do not remove the paper until the indicator turns off.
2
Set the bypass tray guides to the width
of the paper.
of the paper.
Grasp the bypass guide lock lever and adjust the vertical
bypass guide, and then release the lever. Adjust the bypass
guide at the bottom edge of the paper to the paper size.
bypass guide, and then release the lever. Adjust the bypass
guide at the bottom edge of the paper to the paper size.
When loading paper larger than 8-1/2" x 11"R or A4R, be sure
to pull out the bypass tray extension. Pull the bypass tray
extension all the way out. If the bypass tray extension is not
pulled all the way out, the size of the loaded paper will not be
correctly displayed.
If you are loading paper larger than 12" x 18" (A3W) size,
remove the bottom edge bypass guide.
to pull out the bypass tray extension. Pull the bypass tray
extension all the way out. If the bypass tray extension is not
pulled all the way out, the size of the loaded paper will not be
correctly displayed.
If you are loading paper larger than 12" x 18" (A3W) size,
remove the bottom edge bypass guide.
Do not place heavy objects on the bypass tray or press down on the tray.
3
Insert the paper along the bypass tray
guides all the way into the bypass tray
until it stops.
guides all the way into the bypass tray
until it stops.
Load the paper with the print side face up.
The paper stack must not be higher than the indicator line.
A maximum of 500 sheets of paper can be loaded in the tray.
The paper stack must not be higher than the indicator line.
A maximum of 500 sheets of paper can be loaded in the tray.
• Do not force the paper in.
• If the bypass tray guides are set wider than the paper, move the bypass tray guides in until they correctly fit the
width of the paper. If the bypass guides are set too wide, the paper may skew or be creased.
4
Press the operation button.
After the button is pressed, the paper table will rise. While the
paper tray rises, the operation button indicator will blink. After
the paper tray finishes rising, the indicator will light solidly.
paper tray rises, the operation button indicator will blink. After
the paper tray finishes rising, the indicator will light solidly.
50
Bypass tray paper settings
After loading paper in the bypass tray, configure settings for the loaded paper.
1
Touch the [Paper Select] key.
2
Touch the paper type key of the bypass
tray.
tray.
(A) Shows the size of paper loaded in the bypass tray.
(B) Shows the currently selected paper type.
(B) Shows the currently selected paper type.
3
Select the type of paper used in the
bypass tray.
bypass tray.
Select the paper type to be used.
Special Modes
Plain
2-Sided Copy
Output
File
Quick File
Copy Ratio
1.
2.
7.
8½x11
8½x11
Original
Paper Select
Auto
8½x11
Plain
Auto
8½x11
Exposure
Auto
8½x14
4.
11x17
11x17
6.
11x17
5.
11x17
3.
8½x11
100%
Paper Select
Paper Tray
Bypass Tray
Large Capacity
Tray
OK
Plain
Plain
Plain
2. 8½x11
8½x11
Plain
Plain
5. 11x17
Plain
6. 11x17
Plain
7. 11x17
3. 11x17
4. 8½x14
1. 8½x11
Plain
(B)
(A)
Paper Select
Cancel
Plain
Pre-Punched
Heavy Paper 1
Pre-Printed
Color
Heavy Paper 2
Recycled
Thin Paper
Heavy Paper 3
Letter Head
Heavy Paper 1: 28+ - 32 lbs.bond (106 - 128
g/m
2
)
Bypass Tray Type/Size Setting
Select the paper type.
1
2
Heavy Paper 2: 32+ lbs.bond, -65 lbs.cover (129 - 176
g/m
2
)
Heavy Paper 3: 48 lbs.bond, 110 lbs.index (177 - 205
g/m
2
)
51
4
Example: recycled paper has been selected
Set the paper size.
[Auto-Inch] key
When the paper inserted in the bypass tray is a standard inch
size (8-1/2" x 11", etc.), the paper size will be detected
automatically and the appropriate paper size set.
When the paper inserted in the bypass tray is a standard inch
size (8-1/2" x 11", etc.), the paper size will be detected
automatically and the appropriate paper size set.
[Auto-AB] key
When the paper inserted in the bypass tray is a standard AB size
(A4 size, etc.), the paper size will be detected automatically and
the appropriate paper size set.
When the paper inserted in the bypass tray is a standard AB size
(A4 size, etc.), the paper size will be detected automatically and
the appropriate paper size set.
[Custom Size] key
Touch this key when you know the size of the inserted paper but
it is not one of the standard inch or AB sizes.
When the key is touched, the paper size entry screen appears.
Touch the [X] key and enter the horizontal dimension of the
paper with the
Touch this key when you know the size of the inserted paper but
it is not one of the standard inch or AB sizes.
When the key is touched, the paper size entry screen appears.
Touch the [X] key and enter the horizontal dimension of the
paper with the
keys, and then touch the [Y] key and
enter the vertical dimension. When finished, touch the [OK]
key.
key.
[Manual Settings] key
Special standard sizes such as 320mm x 450mm,
320mm x 225mm, 318mm x 469mm, 318mm x 234mm,
312mm x 440mm, 312mm x 220mm, and 16K, 16KR, and 8K
(used in China) have been pre-stored. Touch the key of the
desired size.
(320mm x 450mm, 320mm x 225mm, 318mm x 469mm,
318mm x 234mm, 312mm x 440mm, and 312mm x 220mm
can only be used in the bypass tray when a large capacity trays
(MX-LCX5) is installed.)
Special standard sizes such as 320mm x 450mm,
320mm x 225mm, 318mm x 469mm, 318mm x 234mm,
312mm x 440mm, 312mm x 220mm, and 16K, 16KR, and 8K
(used in China) have been pre-stored. Touch the key of the
desired size.
(320mm x 450mm, 320mm x 225mm, 318mm x 469mm,
318mm x 234mm, 312mm x 440mm, and 312mm x 220mm
can only be used in the bypass tray when a large capacity trays
(MX-LCX5) is installed.)
[Non-standard size] checkbox
Select when you have loaded a non-standard size of paper.
Select when you have loaded a non-standard size of paper.
If tab paper is selected, check the size. Touch the [Auto-Inch] key or the [Auto-AB] key. When you have finished
checking/changing the setting, touch the [OK] key.
checking/changing the setting, touch the [OK] key.
5
Select the bypass tray.
(1) Touch the paper size key of the bypass tray.
(2) Touch the [OK] key.
Paper Select
Bypass Tray Type/Size Setting
OK
Type
Auto-Inch
Recycled
Custom Size
Manual
X11 Y17
Auto-AB
Size
12x18(A3W),11x17,8½x14
8½x11,5½x8½R
7¼x10½R,9x12(A4W),A3,A4,B4
A3W(12x18),A3,B4,A4,A5R,B5
B5R,A4W(9x12)11x17,8½x11
A4R
8½x11,5½x8½R
7¼x10½R,9x12(A4W),A3,A4,B4
A3W(12x18),A3,B4,A4,A5R,B5
B5R,A4W(9x12)11x17,8½x11
A4R
Non Standard
Size
OK
OK
(4~12 5/8)
inch
inch
(5 1/2~18 1/2)
inch
inch
11
X
Y
17
Bypass Tray Type/Size Setting
Size Input
Paper Select
Paper Tray
Bypass Tray
Large Capacity
Tray
OK
Plain
Plain
Plain
Plain
2. 8½x11
8½x11
Plain
Recycled
5. 11x17
Plain
6. 11x17
Plain
7. 11x17
3. 11x17
4. 8½x14
1. 8½x11
(1)
(2)
52
IMPORTANT POINTS WHEN USING THE BYPASS TRAY
• When using plain paper other than SHARP standard paper or special media other than SHARP-recommended
transparency film, or when printing on the reverse side of previously used paper, the paper must be loaded one sheet
at a time. Loading more than one sheet at a time will cause misfeeds.
at a time. Loading more than one sheet at a time will cause misfeeds.
• Before loading paper, straighten any curling in the paper.
• When adding paper, remove any paper remaining in the bypass tray, combine it with the paper to be added, and
• When adding paper, remove any paper remaining in the bypass tray, combine it with the paper to be added, and
reload as a single stack. If paper is added without removing the remaining paper, a misfeed may result.
Inserting paper
Place paper that is 7-1/4" x 10-1/2" (A5) or smaller in the horizontal orientation.
Inserting tab paper
To print on tab paper, load tab paper in the bypass tray with the print side face up.
On the MX-MFX2 bypass tray, the special guide is attached to the bottom edge bypass guide. The special guide is stored
under the front cover of the large capacity trays. After using the guide, remove it and replace it in its storage location.
On the MX-MFX2 bypass tray, the special guide is attached to the bottom edge bypass guide. The special guide is stored
under the front cover of the large capacity trays. After using the guide, remove it and replace it in its storage location.
Inserting transparency film
Bypass tray (MX-MFX1)
Bypass tray (MX-MFX2)
Left
binding
Place the first sheet of tab paper so that the tab is away from you.
Right
binding
Place the first sheet of tab paper so that the tab is toward you.
• Use only tab paper that is made of paper. Tab paper made of a material other than paper (film, etc.) cannot be used.
• To print on the tabs of tab paper...
In copy mode, use "Tab Copy" in the special modes. In print mode, use the tab print function. For more information on
these functions, see the Copier Guide and the Printer Guide.
these functions, see the Copier Guide and the Printer Guide.
• Use SHARP-recommended transparency film. When inserting transparency film
in the bypass tray, the rounded corner should be at the far left when the film is
oriented horizontally, or at the far right when the film is oriented vertically. Place
the film face up.
oriented horizontally, or at the far right when the film is oriented vertically. Place
the film face up.
• When loading multiple sheets of transparency film in the bypass tray, be sure to
fan the sheets several times before loading.
• When printing on transparency film, be sure to remove each sheet as it exits the
machine. Allowing sheets to stack in the output tray may result in curling.
Front
side
side
Front
side
side
Front
side
side
Front
side
side
Horizontally
Vertically
Click on the first or last page to see other MX-M950 / MX-MM1100 (serv.man50) service manuals if exist.