Sharp MX-M950 / MX-MM1100 (serv.man50) User Manual / Operation Manual ▷ View online
37
TRAY SETTINGS FOR THE LARGE CAPACITY TRAYS
(MX-LCX4)
(MX-LCX4)
Loading paper and changing the paper size
Up to 1000 sheets of 5-1/2" x 8-1/2"R, 8-1/2" x 11", or 9" x 12" size paper (A4R, B5, A4, or A4W size paper) can be
loaded in tray 5 and tray 6. Up to 2550 sheets of the same sizes of paper as tray 5 and tray 6 can be loaded in tray 7.
For detailed information on the paper that can be loaded, see the specifications in the Safety Guide and "
loaded in tray 5 and tray 6. Up to 2550 sheets of the same sizes of paper as tray 5 and tray 6 can be loaded in tray 7.
For detailed information on the paper that can be loaded, see the specifications in the Safety Guide and "
PAPER TRAY
SETTINGS
" (page 77) in the System Settings.
This section explains the procedures for adding paper to tray 5, tray 6, and tray 7, and for changing the paper size of tray
5 and tray 6. If you need to change the paper size of tray 7, consult your dealer or nearest SHARP service department.
(In this case, a service technician must change the paper size setting.)
5 and tray 6. If you need to change the paper size of tray 7, consult your dealer or nearest SHARP service department.
(In this case, a service technician must change the paper size setting.)
1
Pull out the paper tray.
Gently pull the tray out until it stops. If you are simply adding
paper, go to step 8.
paper, go to step 8.
2
Remove the screws that secure paper
guides A and B, and remove the guides.
guides A and B, and remove the guides.
3
Adjust the paper guide (A) to the paper size.
(1) Align the bottom of the paper guide (A) with
the appropriate slot on the base of the tray.
Align the paper size guide with the slot for the paper size
to be used (indicated by the paper size mark).
to be used (indicated by the paper size mark).
(2) Align the hole in the paper size indicator at the
top of paper guide A with the screw hole.
(3) Tighten the screw to secure paper guide A.
4
Repeat step 2 to change paper guide B.
5
Adjust the paper guide (C) to the paper size.
(1) Remove the screw that secures paper guide
C, and remove the guide.
(2) Attach paper guide C at the desired paper size.
(3) Tighten the screw to secure paper guide C.
(A)
(B)
(1)
(2)
(3)
(1), (3)
(2)
(C)
38
6
Re-insert paper guide D at the desired
paper size.
paper size.
7
Adjust the paper size selector knob to
the new paper size.
the new paper size.
8
Fan the paper.
Fan the paper well before loading it. If the paper is not fanned,
multiple sheets may feed at once and cause a misfeed.
multiple sheets may feed at once and cause a misfeed.
9
Insert the paper into the tray.
Load paper face down. The stack must not exceed the indicator
line (up to 1000 sheets in tray 5 or tray 6, or up to 2550 sheets
in tray 7).
line (up to 1000 sheets in tray 5 or tray 6, or up to 2550 sheets
in tray 7).
10
Gently push the paper tray into the
machine.
machine.
Push the tray firmly all the way into the machine.
If you loaded a different type of paper than was loaded previously, change the paper type setting as explained in
"
"
PAPER TRAY SETTINGS
" (page 77) in the System Settings. If the paper size setting is not configured correctly,
automatic paper selection will not operate correctly and printing may take place on the wrong size or type of paper or
a misfeed may occur.
a misfeed may occur.
Do not place heavy objects on the tray or press down on the tray.
((D)
39
Loading tab paper and transparency film
In addition to plain paper, tab paper, transparency film, and other special media can be loaded in tray 5, tray6, and tray7.
To load tab paper or transparency film in tray 5, tray 6, and tray 7, follow the steps below.
To load tab paper or transparency film in tray 5, tray 6, and tray 7, follow the steps below.
Loading tab paper
To use tab paper, the special guide must be attached as explained below.
Loading transparency film
When loading transparency film, load the film face up in the vertical orientation with the rounded corner at the top right.
1
Take out the tab paper guide.
The guide is stored under the cover of the large capacity trays. When finished using tab paper, be sure to replace the guide.
2
Adjust the paper guide to the tab paper
position and load tab paper.
position and load tab paper.
To adjust the paper guide, see
Loading paper and changing the
paper size
(page 37).
Place the tab paper with the print side face up and the tabs to
the right.
the right.
[Example]
Make sure that the positions of the tabs correspond with the originals as shown below.
Make sure that the positions of the tabs correspond with the originals as shown below.
3
Attach the special guide as shown.
4
Gently push the tray in and set the paper
type to tab paper.
type to tab paper.
Change the paper type setting to tab paper as explained in
"
"
PAPER TRAY SETTINGS
" (page 77) in the System Settings.
ABC
DEF
GHI
JKL
1st sheet
2nd sheet
3rd sheet
4th sheet
Bottom
Top
1st sheet
Front
side
4th sheet
3rd sheet
2nd sheet
Originals
Tab paper
40
TRAY SETTINGS FOR THE LARGE CAPACITY TRAYS
(MX-LCX5)
(MX-LCX5)
Loading paper and changing the paper size
Up to 1000 sheets of 5-1/2" x 8-1/2"R to 12" x 18" size paper (A5R to A3W size paper) can be loaded in tray 5 and tray
7. Up to 2000 sheets of 5-1/2" x 8-1/2"R to 12" x 18" size paper (A5R to A3W size paper) can be loaded in tray 6.
For detailed information on the paper that can be loaded, see the specifications in the Safety Guide and "
7. Up to 2000 sheets of 5-1/2" x 8-1/2"R to 12" x 18" size paper (A5R to A3W size paper) can be loaded in tray 6.
For detailed information on the paper that can be loaded, see the specifications in the Safety Guide and "
PAPER TRAY
SETTINGS
" (page 77) in the System Settings.
This section explains the procedures for adding paper to tray 5, tray 6, and tray 7, and for changing the paper size.
1
Pull out the paper tray.
Gently pull the tray out until it stops.
If you are simply adding paper, go to step 4. To load a different
size of paper, go to the next step.
If you are simply adding paper, go to step 4. To load a different
size of paper, go to the next step.
2
Adjust the vertical paper guide to the
desired paper size.
desired paper size.
(1) Remove the screw on the right side, and
loosen the screw on the left side.
(2) Adjust the paper guide to the paper size
that will be used.
For a standard size, align the screw hole with the hole
indicating the paper size.
indicating the paper size.
(3) Tighten the screw on the right side and then
tighten the screw on the left side.
For a standard paper size, insert the screw into the
aligned holes and tighten the screw.
For a non-standard paper size, insert the screw into the
screw hole in the slot on the right side and tighten the
screw.
aligned holes and tighten the screw.
For a non-standard paper size, insert the screw into the
screw hole in the slot on the right side and tighten the
screw.
3
Adjust the right paper guide to the paper
size.
size.
(1) Release the lock lever on the paper guide
and adjust the paper guide to the desired
paper size.
paper size.
(2) Push the lock lever on the paper guide
down so it is horizontal to secure the paper
guide.
guide.
Screw holes for standard sizes
Screw holes for non-standard
sizes
sizes
(1), (3)
(1), (3)
(2)
Click on the first or last page to see other MX-M950 / MX-MM1100 (serv.man50) service manuals if exist.