Sharp MX-M364N / MX-565N Handy Guide ▷ View online
Consumables
8
SHARP
Document Solution Centre
TRANSFER SECTION:
MX-M365N
MX-M465N
MX-M565N
MX-M565N
Product Code
Description / Contents
Approx. Life
MX-560TU
Primary Transfer Kit:-
Transfer roller
Discharge plate
300k
PERIPHERALS
MX-SCX1
Staple Cartridge (for MX-FN10 & MX-FN17)
5000 staples (x 3)
AR-SC2
Staple Cartridge (for MX-FN11 & MX-FN18)
5000 staples (x 3)
AR-SC3
Saddle Staple Cartridge (for MX-FN10 & MX-FN18)
2000 staples (x 3)
AR-SV1
Stamp Cartridge (for AR-SU1)
2 cartridges
Notes:
* The consumable life is specified by 840K rotations therefore, the page count life indicated above is for
approx. guidance only.
Also, the consumable life may vary, depending on the document density, temperature, humidity and
machine operation.
* The consumable life is specified by 840K rotations therefore, the page count life indicated above is for
approx. guidance only.
Also, the consumable life may vary, depending on the document density, temperature, humidity and
machine operation.
Initial Setup
SHARP
Document Solution Centre
9
DEVELOPER SET-UP
Sim 25-02
Auto Developer Adjustment - Select K.
Toner Installation must be performed after Auto Developer Adjustment is
completed.
completed.
**For optimum image quality & performance, it is recommended to setup &
install developer at the customer site.
install developer at the customer site.
TONER INSTALLATION & REPLENISHMENT
Install K Toner Cartridge
Caution:
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation Mode
during Initial Toner Replenishment.
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation Mode
during Initial Toner Replenishment.
PRODUCT ACTIVATION & FIRMWARE UPGRADE
Activation of Optional Product(s):-
System Settings – Administrator Mode – Product Key.
Sim 22-05
Check Firmware version(s):-
Upgrade to latest version.
INITIAL SETUP
Sim 26-01
Right Tray Installation
Yes/No.
Sim 26-02
LCC Installation (Paper Size):-
A4.
Sim 26-06
Machine Destination.
Sim 26-35
Set Multi Error Counter
Set to 1 (Multi Count).
Sim 26-50
Long Paper Support (up to 1200mm),
0 = Disable, 1 = Enable
.
Sim 26-52
Non Printed Paper Counter Set-up.
Sim 55-03
Process Mixed Size Pages (orientation) when Printing in Duplex:-
SSW 3-6,
SSW 3-6,
0 = Disable, 1 = Enable.
Sim 55-03
Toner Remain Status Display: SSW 22-5,
0 = Disable, 1 = Enable.
System Settings: Adjust Date/Time (Inc. Daylight Saving setting).
Network Settings – Print Port Settings: Disable WSD.
Set cassette size by adjusting the guides in the cassette.
Paper Size & Type Setting:-
System Settings – Paper Tray Settings.
IMAGE SKEW [ENGINE]
Sim 64-02
Check LSU Parallelism.
Select A=1, B=1, C=254, D=255
Initial Setup
10
SHARP
Document Solution Centre
PRINT IMAGE POSITION & MAGNIFICATION
Automatic Adjustment:-
Sim 50-28
BK MAG ADJ (Main Scan Mag).
SETUP/PRINT ADJ (Lead, Offset or All).
Manual Adjustment:-
Sim 50-10
BK MAG (inside dimension) to 240mm.
Sim 50-10
Image Off Centre Adjustment.
Sim 50-05
Printer Lead Edge & Void Adjust.
HALF TONE CALIBRATION
Sim 46-74
Engine & Printer Calibration
Select FACTORY Mode.
COPY IMAGE QUALITY
Check Image Quality (Copy Mode) – Density, Magnification, Lead Edge & Void.
If NG, perform the following adjustments as required:-
Sim 46-02
Copy Density Adjust.
Sim 46-09
SPF Copy Density Adjust.
Sim 50-28
OC ADJUST (Lead, Offset & Mag).
SPF ADJ:(Lead, Offset & Sub scan).
Manual Adjustment (Magnification, Lead Edge, Void, Off Centre etc).:
Sim 48-01
Magnification Adjustment (OC & SPF).
Sim 50-01
Lead/Rear Edge, Loss & Void Adjust.
Sim 50-12
OC & SPF Off Centre Adjust.
PRINT IMAGE QUALITY
Check Image Quality (Print Mode) – Density.
Sim 64-05
PCL Density Test Page
Sim 64-06
PS Density Test Page
PERIPHERAL / OPTION CONFIGURATION
FAX OPTION – MX-FX11
Sim 66-02
Fax SW Setting (Destination).
Sim 66-10
Fax Memory Clear (For Extended Memory).
Sim 66-39
Fax Destination Set.
Initial Setup
SHARP
Document Solution Centre
11
PERIPHERAL / OPTION CONFIGURATION
FINISHER OPTION – MX-FN10, MX-FN11, MX-FN17, MX-FN18
Sim 03-10
Saddle Fold/Staple Position Adjustment [MX-FN10/18 only]
Sim 26-65
Finisher Alarm Mode:-
Limit number of Copies in staple mode
(ON/OFF).
EXTERNAL KEYBOARD – MX-KB11N
Keyboard Language Setting:
System Settings – Default Settings – Keyboard Select:
Select English(US).
EXTERNAL ACCOUNTING MODULE – MX-AMX3
Sim 55-03
Auto clear function before Copy job execution:-
SSW 1-5
0 = Disable, 1 = Enable.
Sim 55-03
USB Card Reader detection control:-
SSW 6-8
0 = Disable, 1 = Enable.
Sim 55-03
Continuous print mode (job queuing for OSA):-
SSW 24-7
0 = Disable, 1 = Enable.
MFP DATA BACKUP
Sim 22-06
Data Simulation Print.
Device Clone & Storage Backup.
Sim 56-01
Backup EEPROM Data to HDD.
Click on the first or last page to see other MX-M364N / MX-565N service manuals if exist.