Sharp MX-M364N / MX-565N Handy Guide ▷ View online
CF Card Replacement Procedure
SHARP
Document Solution Centre
37
Only limited data that is stored on the CF Card can be backed up and reinstalled following replacement or
CF card failure. If the CF Card is operating normally before replacement, backup the data and then
reinstall the data onto the replacement CF Card.
CF card failure. If the CF Card is operating normally before replacement, backup the data and then
reinstall the data onto the replacement CF Card.
Partition
Number
Stored Data
Backup
Method
L-201
ICU firmware data
ICU firmware (Including OS section)
Log data
Snapshot
Swap area
Log data
Snapshot
Swap area
-
S-201
ICU firmware fixed
data (Pre-install)
Font
Web help
SPDL
Option Font ROM
Lang (Message data)
Graph (Graphic data)
eOSA delegator
Option Font ROM
Web help
SPDL
Option Font ROM
Lang (Message data)
Graph (Graphic data)
eOSA delegator
Option Font ROM
-
S-203
System Data
Setting value data file
(System setting/SIM setting data (Image quality
adjustment)/FAX Soft SW)
(System setting/SIM setting data (Image quality
adjustment)/FAX Soft SW)
SIM56-02
Replacement Procedure:
When replacing the CF card, be sure to use the specified CF card supplied as a service part only.
The firmware required for booting the MFP device must be included on the CF card that is used in
this machine - Commercially available CF cards do not have this firmware data.
this machine - Commercially available CF cards do not have this firmware data.
1. Use SIM56-02 to back up the CF card data to the USB memory.
2. When the operation panel home screen has been customised, backup the CF card data by using
the device cloning function.
3. Replace the CF card with a new one.
4. Upgrade the firmware to the latest version.
5. Use SIM56-02 to restore the data backed up in procedure 1.
6. Restore the data backed up in procedure 2 by using the device cloning function.
Notes:
If E7-A6 trouble occurs and the error cannot be cancelled, this may indicate an issue or failure of
the CF Card – replace the CF Card by following the procedure detailed above.
the CF Card – replace the CF Card by following the procedure detailed above.
Firmware & Print Driver Revision
38
SHARP
Document Solution Centre
Engine Firmware:
Firmware ROM
ICUM MAIN
02.00.o1.d0
ICU MAIN
02.00.o1.00
ICU BOOT
02.00.o1.00
PCU
03.00.o1.00
SCU
01.00.o1.0a
DESK
03.00.G1.00
DSPF
01.00.o1.00
UI CONTENTS
02.00.o1.00
LCC [MX-LC11]
01.00.A1.00
SADDLE FINISHER [MX-FN10]
01.14.02.00
FINISHER 4K [MX-FN11 & MX-FN18]
01.08.02.0a
INNER FINISHER [MX-FN17]
02.01.03.00
SADDLE [MX-FN18]
01.02.03.00
PUNCH [MX-PNX6]
01.02.02.00
FAX MAIN [MX-FX11]
01.01.G1.00
DATA SECURITY KIT [MX-FR44U]
02.00.oc.a0
ACU [MX-EB11]
01.00.o1.00
WATERMARK
01.00.00.00
E-MANUAL
01.30.o1.00
Print Driver:
Driver
Windows OS x86
2008, XP, 7, 8, 8.1
Windows OS x64
2008(R2), 2012(R2), XP, 7, 8, 8.1
PCL6
09.03.04.45 [WHQL]
09.03.04.45 [WHQL]
PS
09.03.04.46 [WHQL]
09.03.04.46 [WHQL]
PPD
1.5.0.11 [WHQL]
1.5.0.11 [WHQL]
PC-Fax
3.8.8.15
3.8.8.15
TWAIN
3.01.011.000 [WHQL]
3.01.011.000 [WHQL]
XPS **
01.03.38.01 [WHQL]
01.03.38.01 [WHQL]
Sharp UD
02.01.20.18 [WHQL]
02.01.20.18 [WHQL]
Note: ** XPS driver supports Windows Vista only.
For the latest Firmware and Print Driver version(s),
For the latest Firmware and Print Driver version(s),
please refer to the SHARP Support Website.
Test Simulation
SHARP
Document Solution Centre
39
The following pages contain information regarding test simulations. For a detailed description for each
test simulation, please refer to the MX-M365/465/565N Service Manual.
Simulation Entry Method:
test simulation, please refer to the MX-M365/465/565N Service Manual.
Simulation Entry Method:
1. Double-click the [HOME] key. (Total use quantity/Toner remaining quantity display mode screen
will appear):-
2. Touch the VER display section (as indicated below):-
3.
Touch
keys:-
4. Enter a main SIM code with the 10-key pad then touch the START (MONO or COLOR) key or select
a main code from the SIM key list on the touch panel.
#
C
*
*
Test Simulation
40
SHARP
Document Solution Centre
1
Scanner Self Test
1
Scanner operations test
2
Scanner sensor check
5
Scanner unit and control circuit check
2
SPF Self Test
1
SPF ageing test.
2
SPF sensor check
3
SPF output check (motor, clutch, solenoid)
3
Finisher Operation & Test
2
Finisher sensor check
3
Finisher output / load check
10 Finisher adjustment
4
LCC / Desk Operation & Test
2
LCC sensor check
3
LCC output / load check
5
DTRC clutch operation check
5
Lamp Operation & Test
1
LCD/LED operation panel test
2
Heater lamp load check
3
Scanner lamp control circuit check
4
Discharge lamp control circuit check
6
System Load Operation & Test
1
Paper Feed output / load check
2
Fan control circuit check
90 Reset machine to factory setting (scanner
mirror unit lock position execute).
7
Device Aging Operation & Test
1
Ageing test setting
6
Interval ageing cycle timer set up
8
Warm up time display setting
12 Document reading setting (aging)
8
High Voltage Operation & Test
1
Developer bias setting and output
2
MHV/Grid setting and output
6
Transfer setting and output
17 Separation bias voltage setting
9
Duplex Operation & Test
2
ADU sensor check
3
ADU load & output check
10
Toner Motor Operation & Test
1
Toner motor operation check
13
U1 Clear / Cancel
--
Trouble cancel (U1 trouble).
14
Clear / Cancel
--
Trouble cancel (excluding U2/PF trouble).
15
U6 Clear / Cancel
--
Trouble cancel (excluding U2/PF trouble).
16
U2 Clear / Cancel
--
U2 trouble cancel
21
Maintenance Cycle Configuration
1
Maintenance cycle setting
22
Data Output & Check
1
Counter data display
2
Jam/trouble counter display
3
Jam history data display
4
Trouble code history data display
5
ROM version display
6
Data print mode
8
SPF & Scanner output counter display
9
Paper feed counter display
10 Machine system display
11 Fax counter display
12 SPF jam history display
13 Process cartridge counter display
14 Toner cartridge use status
18 User data delete history
19 Image Send counter display
25 Toner usage estimator data display
40 Error code list display
42 JAM/Trouble data check
43 JAM data details display
90 System setting list print
11 Fax counter display
12 SPF jam history display
13 Process cartridge counter display
14 Toner cartridge use status
18 User data delete history
19 Image Send counter display
25 Toner usage estimator data display
40 Error code list display
42 JAM/Trouble data check
43 JAM data details display
90 System setting list print
23
Data Print Mode & Check
2
Print jam/Trouble data print mode
80 Data print mode (paper feed)
81 Backup paper feed real time data to USB
81 Backup paper feed real time data to USB
memory
Click on the first or last page to see other MX-M364N / MX-565N service manuals if exist.