Sharp MX-M310 / MX-M310N (serv.man11) User Manual / Operation Manual ▷ View online
23
2
NORMAL COPYING
COPYING FROM THE DOCUMENT GLASS
1
Open the document cover/RSPF and
place the original face down on the
document glass.
place the original face down on the
document glass.
[How to place the original]
Align the corner or the original with the tip of the arrow
(
Align the corner or the original with the tip of the arrow
(
) at the left rear corner of the glass as shown in the
illustration.
2
Close the document cover/RSPF.
The original size appears
in the touch panel.
After placing the original,
be sure to close the
document cover/ RSPF.
If left open, parts outside
of the original will be
copied black, causing
excessive use of toner.
in the touch panel.
After placing the original,
be sure to close the
document cover/ RSPF.
If left open, parts outside
of the original will be
copied black, causing
excessive use of toner.
3
Make sure that the same size of paper as
the original is automatically selected.
the original is automatically selected.
The selected tray is
highlighted. If the tray
contains a different size of
paper than the original,
"LOAD xxxx PAPER." will
appear.
highlighted. If the tray
contains a different size of
paper than the original,
"LOAD xxxx PAPER." will
appear.
Even if the message above is displayed, copying can
be performed using the selected paper tray.
be performed using the selected paper tray.
Manually selecting the paper size (paper tray)
If auto paper selection is disabled in the administrator
settings, or if you wish to use a different size of paper
than the original, touch the [PAPER SELECT] key and
select the paper tray with the desired paper size. (The
selected paper will be highlighted and the paper selecting
screen will close.)
To close the screen without selecting a paper size, touch
the [PAPER SELECT] key again.
settings, or if you wish to use a different size of paper
than the original, touch the [PAPER SELECT] key and
select the paper tray with the desired paper size. (The
selected paper will be highlighted and the paper selecting
screen will close.)
To close the screen without selecting a paper size, touch
the [PAPER SELECT] key again.
4
Select the number of copies and any
other desired copy settings, and then
press the [START] key (
other desired copy settings, and then
press the [START] key (
).
• The number in the copy quantity display will
decrease by 1 each time a copy is made.
• If you are only making a single copy, the copy can be
made with the copy number display showing "0".
• To clear a mistake, press the [CLEAR] key ( ).
If "AUDITING MODE" (p.95) has been enabled, enter your 5-digit account number.
Note
If the original size is not automatically
detected, manually set the original size. (p.48)
detected, manually set the original size. (p.48)
R
A4
R
B5
B5
A4
B4
A3
Original scale
Original scale
Note
A4
A4
A4
A4
A3
• To load paper, see "LOADING PAPER"
(p.16). If you change the paper size in the
tray, you will also need to change the tray's
paper size and paper type settings. (p.20)
tray, you will also need to change the tray's
paper size and paper type settings. (p.20)
• The paper types for the auto paper selection
function can be selected, or the function disabled,
in the administrator settings. (See "6. SYSTEM
SETTINGS (ADMINISTRATOR)".)
in the administrator settings. (See "6. SYSTEM
SETTINGS (ADMINISTRATOR)".)
• Press the [CLEAR] key (
) to stop
copying in the middle of a run.
• To repeat the same copy sequence for a
different original, simply replace the
original and press the [START] key (
original and press the [START] key (
).
• If copying stops because the tray has run
out of paper, you can resume copying by
touching the [PAPER SELECT] key and
selecting the bypass tray or a paper tray
that has the same size and type of paper
loaded in the same orientation.
touching the [PAPER SELECT] key and
selecting the bypass tray or a paper tray
that has the same size and type of paper
loaded in the same orientation.
Note
READY TO COPY.
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
A3
0
PLAIN
EXTRA IMAGE
ADJUST
PLAIN
1.A4
2.B4
RECYCLED
UT
LOGOUT
Note
MX-M310.book 23 ページ 2009年8月7日 金曜日 午後1時10分
24
COPY FUNCTIONS
COPYING FROM THE RSPF
1
Make sure that an original has not
been left on the document glass and
then close the RSPF.
been left on the document glass and
then close the RSPF.
If an original remains on
the document glass after a
copy was made,
"REMOVE THE
ORIGINAL FROM THE
DOCUMENT GLASS." will
appear in the touch panel.
the document glass after a
copy was made,
"REMOVE THE
ORIGINAL FROM THE
DOCUMENT GLASS." will
appear in the touch panel.
2
Adjust the original guides to the size
of the original.
of the original.
3
Place the originals face up in the
document feeder tray.
document feeder tray.
Insert the originals all the
way into the feed slot.
The original size appears
in the touch panel.
way into the feed slot.
The original size appears
in the touch panel.
4
Make sure that the same size of paper
as the original is selected.
as the original is selected.
The selected tray is
highlighted. If none of the
trays have the same size
of paper as the original,
"LOAD xxxx PAPER."
will appear.
highlighted. If none of the
trays have the same size
of paper as the original,
"LOAD xxxx PAPER."
will appear.
Even if the message above is displayed, copying can
be performed using the selected paper tray.
be performed using the selected paper tray.
5
Select the number of copies and any
other desired copy settings, and then
press the [START] key (
other desired copy settings, and then
press the [START] key (
).
• The number in the copy quantity display will
decrease by 1 each time a copy is made.
• If you are only making a single copy, the copy can be
made with the copy number display showing "0".
• To clear a mistake, press the [CLEAR] key ( ).
Stream feeding mode
If stream feeding mode is enabled in the administrator
settings, "SET ORIGINALS FOR STREAM FEEDING."
will appear in the touch panel for approximately 5
seconds after the originals are fed. Any new originals
placed in the RSPF while this message appears will be
fed and copied automatically.
settings, "SET ORIGINALS FOR STREAM FEEDING."
will appear in the touch panel for approximately 5
seconds after the originals are fed. Any new originals
placed in the RSPF while this message appears will be
fed and copied automatically.
Copying a large number of originals
Job Build mode is useful when you need to copy more
originals that can be placed in the RSPF at once. For
information on Job Build mode, see "JOB BUILD
MODE" (p.46).
originals that can be placed in the RSPF at once. For
information on Job Build mode, see "JOB BUILD
MODE" (p.46).
• If "AUDITING MODE" (p.95) is enabled, enter your 5-digit account number.
• If the RSPF is disabled in the administrator settings, the RSPF cannot be used. See "6. SYSTEM SETTINGS
• If the RSPF is disabled in the administrator settings, the RSPF cannot be used. See "6. SYSTEM SETTINGS
(ADMINISTRATOR)".
Note
• Up to 100 pages (90
g/m
2
(24 lbs.)) can
be inserted at once. The stack of originals
must not be higher than the indicator line
on the tray.
must not be higher than the indicator line
on the tray.
• If the original size is not automatically
detected, manually set the original size.
(p.48)
(p.48)
Note
A4
A4
A4
A4
A3
• To load paper, see "LOADING PAPER"
(p.16). If you change the paper size in the
tray, you will also need to change the
tray's paper size and paper type settings.
(p.20)
tray, you will also need to change the
tray's paper size and paper type settings.
(p.20)
• If needed, manually select the paper tray
that has the desired size of paper as
explained on page 23.
explained on page 23.
• The paper types for the auto paper selection
function can be selected, or the function
disabled, in the administrator settings. (See "6.
SYSTEM SETTINGS (ADMINISTRATOR)".)
disabled, in the administrator settings. (See "6.
SYSTEM SETTINGS (ADMINISTRATOR)".)
• If the original size is larger than the paper
size, the result of copying from the
document glass may differ from the result
of copying from the RSPF. (p.23)
document glass may differ from the result
of copying from the RSPF. (p.23)
• Press the [CLEAR] key (
) to stop
copying in the middle of a run.
• If copying stops because the tray has run
out of paper, you can resume copying by
touching the [PAPER SELECT] key and
selecting the bypass tray or a paper tray
that has the same size and type of paper
loaded in the same orientation.
touching the [PAPER SELECT] key and
selecting the bypass tray or a paper tray
that has the same size and type of paper
loaded in the same orientation.
Note
UT
LOGOUT
Note
MX-M310.book 24 ページ 2009年8月7日 金曜日 午後1時10分
25
COPY FUNCTIONS
2
POINTS TO NOTE WHEN MAKING COPIES
Document glass and RSPF
• Paper in a different orientation from the original can be selected if the auto paper select or auto image function has
been selected. In this case, the image of the original will be rotated.
• When copying a book or an original that has been folded or crumpled, press down gently on the document
cover/RSPF. This will reduce shadow lines caused by uneven contact between the original and the document
glass.
glass.
• When the centre tray counter function is enabled, the number of pages that can be delivered to the output tray is
limited to 500 (A4 and 8-1/2" x 14" sizes only; the limit for all other sizes is 300 pages.). When the offset function is
used, the limit is approximately 300 pages. When the limit is reached, copying stops and the [START] key ( ) light
turns off. Remove the copies from the centre tray and then press the [START] key ( ) to resume copying. The
centre tray counter function can be disabled in the administrator settings. (See "6. SYSTEM SETTINGS
(ADMINISTRATOR)".)
used, the limit is approximately 300 pages. When the limit is reached, copying stops and the [START] key ( ) light
turns off. Remove the copies from the centre tray and then press the [START] key ( ) to resume copying. The
centre tray counter function can be disabled in the administrator settings. (See "6. SYSTEM SETTINGS
(ADMINISTRATOR)".)
Originals that can be used in the RSPF
A maximum of 100 sheet originals of equal size (A4, 90
g/m
2
(8-1/2" x 11", 24 lbs.)) can be placed in the RSPF.
Originals of different length can be placed together in the RSPF as long the widths are equal; however, some copy
functions may not operate correctly.
functions may not operate correctly.
Acceptable originals
Originals of size A5 to A3 (5-1/2" x 8-1/2" to 11" x 17") having a weight of 35
g/m
2
to 128
g/m
2
(9 lbs. to 34 lbs.) or
52
g/m
2
to 105
g/m
2
(14 lbs. to 28 lbs.) for two-sided originals can be used.
Other considerations
• Use originals that are within the specified size and weight ranges. Originals outside the specified ranges may
cause misfeeds.
• Make sure that there are no paper clips or staples on the original.
• If an original has damp spots from correction fluid or ink, or glue from pasteups, be sure it has dried completely
• If an original has damp spots from correction fluid or ink, or glue from pasteups, be sure it has dried completely
before using it to make a copy. Otherwise the interior of the RSPF or the document glass may become soiled.
• The following originals cannot be used. These may cause misfeeds, smudging, and unclear images.
• Transparencies, tracing paper, other transparent or translucent paper, photographs
• Carbon paper
• Thermal paper
• Originals that are creased, folded, or torn
• Glued originals, cut-out originals
• Originals with binder holes
• Originals printed using an ink ribbon (thermal transfer printing), originals printed on thermal transfer paper
• Carbon paper
• Thermal paper
• Originals that are creased, folded, or torn
• Glued originals, cut-out originals
• Originals with binder holes
• Originals printed using an ink ribbon (thermal transfer printing), originals printed on thermal transfer paper
Removing the document cover
• To copy large originals like newspaper, remove the document cover.
• To remove it, open the document cover and lift it at a slightly backward angle. To replace the cover, do the
• To remove it, open the document cover and lift it at a slightly backward angle. To replace the cover, do the
reverse.
• The RSPF cannot be removed.
MX-M310.book 25 ページ 2009年8月7日 金曜日 午後1時10分
26
COPY FUNCTIONS
Copying originals of mixed length (Mixed feeding)
When using the RSPF, originals of mixed length can be fed together as long as the width of the originals is the same.
To copy originals of mixed length, follow these steps:
To copy originals of mixed length, follow these steps:
1
Touch the [SPECIAL MODES] key.
2
Touch the
key and then the
[ORIGINAL SIZE] key.
3
Select the "MIX SIZE ORIGINAL
FEEDING MODE" checkbox.
FEEDING MODE" checkbox.
4
Touch the [OK] key.
The setting is entered and
you return to the main
screen.
The original size icon
changes to
you return to the main
screen.
The original size icon
changes to
(
)
to indicate
that mixed feeding is
selected.
selected.
Automatic copy image rotation (Rotation copying)
If the originals are placed in a different orientation than the copy paper, the original image will be automatically
rotated 90
rotated 90
°
. (When an image is rotated, a message will be displayed.) If a function is selected that is not suitable for
rotation, such as enlarging the copy to greater than A4 (8-1/2" x 11") size or margin shift copy, rotation will not be
possible.
possible.
[Example]
• This function operates in both the auto paper select and auto image modes. Rotation copying can be disabled in
the administrator settings. (See "6. SYSTEM SETTINGS (ADMINISTRATOR)".)
2-SIDED COPY
SPECIAL MODES
ORIGINAL
SIZE
CARD SHOT
COV
AL MODES
MANUAL
ORIGINAL SIZE
AUTO
MIX SIZE ORIGINAL FEEDING MODE
OK
When copying is started in mixed feeding
mode, all originals are scanned before
copying begins.
mode, all originals are scanned before
copying begins.
OK
A4
Note
Orientation of
the placed original
Orientation of
the loaded paper
Copy after rotation
Face down
Face down
MX-M310.book 26 ページ 2009年8月7日 金曜日 午後1時10分
Click on the first or last page to see other MX-M310 / MX-M310N (serv.man11) service manuals if exist.