Sharp MX-M310 / MX-M310N (serv.man11) User Manual / Operation Manual ▷ View online
19
BEFORE USING THE MACHINE
1
Loading paper in the bypass tray
1
Unfold the bypass tray.
To enable correct
detection of the paper
size, be sure to pull out
the bypass tray
extension.
detection of the paper
size, be sure to pull out
the bypass tray
extension.
2
Set the paper guides to the copy
paper width.
paper width.
3
Insert the copy paper (print side
down) all the way into the bypass tray.
down) all the way into the bypass tray.
Important points when inserting paper in the bypass tray
• Be sure to place A6 size paper or envelopes
horizontally as shown in the following diagram.
• Load the paper with the print side facing down.
• When loading envelopes, make sure that they are
straight and flat and do not have loosely glued
construction flaps (not the closure flap).
construction flaps (not the closure flap).
• When adding paper, first remove any paper
remaining in the bypass tray, combine it with the
paper to be added, and then reload as a single
stack. The paper to be added must be the same size
and type as the paper already in the bypass tray.
paper to be added, and then reload as a single
stack. The paper to be added must be the same size
and type as the paper already in the bypass tray.
• Do not use paper that is smaller than the original
image. This may cause smudges or unclean images.
• Do not use paper that has already been printed on
by a laser printer or plain paper fax machine. This
may cause smudges or unclean images.
may cause smudges or unclean images.
Landscape
orientation
orientation
Portrait
orientation
orientation
MX-M310.book 19 ページ 2009年8月7日 金曜日 午後1時10分
20
BEFORE USING THE MACHINE
CHANGING A TRAY’S PAPER TYPE AND PAPER SIZE
SETTINGS
SETTINGS
When you change the paper in a tray, follow the steps below to change the tray’s paper type and paper size settings.
The settings cannot be changed when operation has stopped because the paper ran out or a misfeed occurred, or
when an interrupt copy job is being performed.
Even in copy mode, the settings cannot be changed while a print job or received fax is being printed.
The settings cannot be changed when operation has stopped because the paper ran out or a misfeed occurred, or
when an interrupt copy job is being performed.
Even in copy mode, the settings cannot be changed while a print job or received fax is being printed.
1
Load paper in the tray as explained in
"Loading the paper in the paper tray"
(p.18).
"Loading the paper in the paper tray"
(p.18).
2
Press the [SYSTEM SETTINGS] key.
The system settings
menu screen will appear.
menu screen will appear.
3
Touch the [TRAY SETTINGS] key.
The tray settings screen
will appear.
will appear.
4
Select the tray in which you loaded
paper.
paper.
For the tray numbers,
see "PAPER" (p.16).
If the desired tray does
not appear in the display,
use the
see "PAPER" (p.16).
If the desired tray does
not appear in the display,
use the
key or
key
to scroll until it appears.
5
Select the size and type of paper that
is loaded in the tray.
is loaded in the tray.
The currently selected paper type will be highlighted.
• To change the paper type selection, touch the
appropriate type key.
• To change the paper size selection, touch the
appropriate size key.
• To change the displayed size selections to inch sizes,
touch [AB
INCH].
6
Touch the [OK] key.
7
A message appears prompting you to
check the paper in the tray. Check the
paper and then touch the [OK] key.
check the paper in the tray. Check the
paper and then touch the [OK] key.
You will return to the tray settings screen.
• A5 (5-1/2" x 8-1/2") size paper can only be set for tray 1.
• B5 size paper cannot be set for tray 2 (However, B5R size paper can be set.).
• Tray settings for trays other than the bypass tray can be prohibited in the administrator settings. (See "6.
• B5 size paper cannot be set for tray 2 (However, B5R size paper can be set.).
• Tray settings for trays other than the bypass tray can be prohibited in the administrator settings. (See "6.
SYSTEM SETTINGS (ADMINISTRATOR)".)
Note
JOB STATUS
CAN
FAX
DATA
LINE
DATA
DATA
SYSTEM SETTINGS
TOTAL COUNT
TRAY SETTINGS
ADDRES
CONTRO
CONTRO
KEYBOARD
SELECT
ADMI
CONTRA
TRAY 1
TRAY 2
TRAY 3
PLAIN / B5
PLAIN / A3
TYPE / SIZE
PLAIN / A4
CUSTOM SETTINGS
TRAY 1 TYPE/SIZE SETTING
TYPE
RECYCLED
PLAIN
COLOUR
LETTER HEAD
A3
B4
B5
A4R
A5
B5R
A4
OK
SIZE
AB
INCH
MX-M310.book 20 ページ 2009年8月7日 金曜日 午後1時10分
21
BEFORE USING THE MACHINE
1
Setting the paper type in the bypass tray
Use either of the following two methods to set the bypass tray's paper type setting.
From the [SYSTEM SETTINGS] key
1
Load paper in the bypass tray as
explained in "Loading paper in the
bypass tray" (p.19).
explained in "Loading paper in the
bypass tray" (p.19).
2
Press the [SYSTEM SETTINGS] key.
The system settings
menu screen will appear.
menu screen will appear.
3
Touch the [TRAY SETTINGS] key.
The tray settings screen
will appear.
Touch the display
switching key to switch
the screen.
will appear.
Touch the display
switching key to switch
the screen.
4
Touch the [BYPASS TRAY] key.
5
Select the type of paper that is loaded
in the tray.
in the tray.
"JAPANESE P/C" refers to official postcards used in
Japan.
Japan.
6
Touch the [OK] key.
You will return to the tray settings screen.
From the [PAPER SELECT] key
1
Load paper in the bypass tray as
explained in "Loading paper in the
bypass tray" (p.19).
explained in "Loading paper in the
bypass tray" (p.19).
2
Touch the [PAPER SELECT] key.
3
Touch the paper type selection key.
4
Select the paper type.
"JAPANESE P/C" refers to official postcards used in
Japan.
Japan.
5
Touch the [PAPER SELECT] key.
You will return to the main screen of copy mode.
JOB STATUS
CAN
FAX
DATA
LINE
DATA
DATA
SYSTEM SETTINGS
TOTAL COUNT
TRAY SETTINGS
ADDRES
CONTRO
CONTRO
KEYBOARD
SELECT
ADMI
CONTRA
TRAY 4
BYPASS
TRAY
TRAY
TYPE / SIZE
PLAIN
PLAIN / A3
SYSTEM SETTINGS
BYPASS TRAY TYPE SETTING
SELECT THE PAPER TYPE.
RECYCLED
PLAIN
COLOUR
HEAVY PAPER
THIN PAPER
LETTER HEAD
LABELS
TRANSPARENCY
ENVELOPE
JAPANESE P/C
OK
EXPOSURE
AUTO A4
PAPER SELECT
100%
READY TO COPY.
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
A3
0
PLAIN
EXTRA IMAGE
ADJUST
RECYCLED
PLAIN
A4
B4
READY TO COPY.
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
0
RECYCLED
PLAIN
COLOUR
HEAVY PAPER
THIN PAPER
LETTER HEAD
LABELS
JAPANESE P/C
TRANSPARENCY
ENVELOPE
MX-M310.book 21 ページ 2009年8月7日 金曜日 午後1時10分
22
2
Chapter 2
COPY FUNCTIONS
This chapter explains basic copying functions such as normal copying, reduction or enlargement, and exposure
adjustment.
adjustment.
MAIN SCREEN OF COPY MODE
The main screen of copy mode shows messages, keys, and settings that are used for copying. Touch a key to make
a selection. The main screen of copy mode appears when the [COPY] key is pressed (Except when the system
settings screen appears.).
a selection. The main screen of copy mode appears when the [COPY] key is pressed (Except when the system
settings screen appears.).
Message display
Status messages are displayed here.
Status messages are displayed here.
Copy number display
Displays the selected number of copies before the
[START] key ( ) is pressed or the number of
remaining copies after the [START] key ( ) is
pressed. A single copy can be made when "0" is
displayed.
Displays the selected number of copies before the
[START] key ( ) is pressed or the number of
remaining copies after the [START] key ( ) is
pressed. A single copy can be made when "0" is
displayed.
[2-SIDED COPY] key (p.28)
Touch to open the duplex copy mode setting screen.
Touch to open the duplex copy mode setting screen.
[OUTPUT] key (p.36)
Touch to select sort, group, staple sort, and other
output settings.
Touch to select sort, group, staple sort, and other
output settings.
[SPECIAL MODES] key (p.40)
Touch to open the special modes selection screen.
Touch to open the special modes selection screen.
[INFORMATION] icon
The [INFORMATION] icon appears in the base
screen when one or more special modes are
selected.
The [INFORMATION] icon appears in the base
screen when one or more special modes are
selected.
Original feed display
This appears when an original is placed in the
RSPF.
This appears when an original is placed in the
RSPF.
Paper size display
This shows the location of the paper trays, the size of
the paper in the trays. "
This shows the location of the paper trays, the size of
the paper in the trays. "
" indicates whether or not
there is paper. A paper tray can be touched to change
the paper tray selection.
the paper tray selection.
Original size display
Displays the original size only when an original is
placed for copying.
Displays the original size only when an original is
placed for copying.
Exposure display
Displays the icon of the selected exposure type
and the exposure scale.
Displays the icon of the selected exposure type
and the exposure scale.
[EXPOSURE] key (p.30)
Use this key to adjust the copy exposure.
Use this key to adjust the copy exposure.
Paper select display
Displays the selected paper size. When auto paper
select mode is selected, "AUTO" appears when
auto paper select mode is selected.
Displays the selected paper size. When auto paper
select mode is selected, "AUTO" appears when
auto paper select mode is selected.
[PAPER SELECT] key (p.23, p.27)
Use this key to select the paper size.
Use this key to select the paper size.
Copy ratio display
Displays the selected copy ratio.
Displays the selected copy ratio.
[COPY RATIO] key (p.32)
Use this key to select the copy ratio.
Use this key to select the copy ratio.
6
7
8
9
10
11
11
12
13
13
14
15
15
A4
A4
A4
A4
A3
• The message will vary depending on
the country and the region.
• The screen will vary depending on the
equipment installed.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
3
15
MX-M310.book 22 ページ 2009年8月7日 金曜日 午後1時10分
Click on the first or last page to see other MX-M310 / MX-M310N (serv.man11) service manuals if exist.