Sharp MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man7) Service Manual ▷ View online
MX-M264U SIMULATION 6 – 4
24
1
Used to clear the jam counter, and the trouble counter.
(After completion of maintenance, clear the counters.)
(After completion of maintenance, clear the counters.)
2
Used to clear the number of use (the number of prints) of each paper feed section.
3
Used to clear the finisher, RSPF, and the scan (reading) unit counter.
4
Used to clear the maintenance counter, the printer counters of the transport unit and the fusing unit.
(After completion of maintenance, clear the counters.)
(After completion of maintenance, clear the counters.)
5
Used to clear the developer counter. (After replacement of developer, clear the counter.)
6
Used to clear the copy counter.
9
Used clear the printer mode print counter and the self print mode print counter.
10
Used to clear the FAX counter. (Only when FAX is installed)
12
Used to clear the document filing counter value.
15
Used to clear the counters related to the scan mode and the image send.
30
Used to initialize the administrator (Admin) password.
31
Used to initialize the service mode password.
35
Used to clear the toner cartridge use status data.
25
1
Used to check the operations of the developing section.
Process (Developing section)
2
Used to make the initial setting of toner density when replacing developer. (Automatic adjustment)
Image process (Photoconductor/
Developing)
Developing)
4
Used to display the operation data of the toner correction quantity. (Not used in the market.)
Process
26
1
Used to set Yes/No of installation of the job separator.
Paper exit
2
Used to set the paper size of the paper feed tray.
(When the paper size is changed, this simulation must be executed to change the paper size in software.)
(When the paper size is changed, this simulation must be executed to change the paper size in software.)
Paper feed
3
Used to set the specifications of the auditor.
(Setting must be made according to the auditor use conditions.)
(Setting must be made according to the auditor use conditions.)
Auditor
5
Used to set the count mode of the total counter and the maintenance counter. (A3/11x17 size)
6
Used to set the specifications (paper, fixed magnification ratio, etc.) of the destination.
10
Used to set the trial mode of the network scanner.
18
Used to set Disable/Enable of the toner save mode operation. (For the Japan and the UK versions.)
30
Used to set the operation mode corresponding to the CE mark (Europe safety standards).
(For slow start to drive the fusing heater lamp)
(For slow start to drive the fusing heater lamp)
32
Used to set the special functions.
35
Used to set the display mode of SIM 22-4 trouble history when a same trouble occurred repeatedly. There
are two display modes: display as one trouble and display as several series of troubles.
are two display modes: display as one trouble and display as several series of troubles.
38
Used to set Continue/Stop of print when the maintenance life is reached.
50
Used to set functions.
51
Used to set the specifications of the serial port operation. (For PCI)
52
Used to set whether non-printed paper (insertion paper, cover paper) is counted up or not.
56
Used to set ON/OFF of the Life Correction.
65
Used to set the finisher alarm mode.
69
Used to set the operating conditions for toner near end.
73
Enlargement continuous shoot, A3 wide copy mode image loss (shade delete quantity) adjustment
74
Used to set the OSA trial mode.
78
Used to set the password of the remote operation panel.
79
Used to set YES/NO of the pop-up display of user data delete result.
27
1
Used to set non-detection of communication error (U7-00) with RIC. (FSS function)
2
Used to set the sender's registration number and the HOST server telephone number. (FSS function)
4
Used to set the initial call and toner order auto send. (FSS function)
5
Used to set the machine tag No. (This function allows the host computer to check the machine tag No.)
(FSS function)
(FSS function)
Communication (RIC/MODEM)
6
Used to set of the manual service call. (FSS function)
7
Used to set of the enable, alert callout. (FSS function)
9
Used to set the paper transport time recording YES/NO threshold value and shading gain adjustment retry
number. (FSS function)
number. (FSS function)
10
Used to clear the trouble prediction history information. (FSS function)
11
Used to check the serial communication retry number and the scanner gain adjustment retry number
history. (FSS function)
history. (FSS function)
13
Used to check the history of paper transport time between sensors. (FSS function)
14
Used to set the FSS function connection test mode.
15
Used to display the FSS connection status.
16
Used to set the FSS alert send.
17
Used to set the FSS paper order alert.
18
Used to clear the FSS paper feed retry counter.
30
1
Used to check the operations of the sensors and the detectors in other than the paper feed section and the
control circuits.
control circuits.
2
Used to check the operations of the sensors and the detectors in the paper feed section and the control
circuits.
circuits.
40
2
Manual paper feed tray paper width sensor adjustment.
Paper feed
7
Used to set the adjustment value of the manual paper feed tray paper width sensor.
Paper feed
41
1
Used to check the operations of the document size sensor and the control circuit.
2
Used to adjust the document size sensor detection level.
3
Used to check the operations of the document size sensor and the control circuit.
Main
Sub
Functions
Section
MX-M264U SIMULATION 6 – 5
43
1
Used to set the fusing temperature in each mode.
4
Used to set the fusing temperature 2 in each mode.
10
Used to set the postcard feed cycle
20
Used to perform the low-temperature, low-humidity (L/L) environment correction for the fusing temperature
setting of each paper (SIM43-01).
setting of each paper (SIM43-01).
22
Used to perform the low-temperature, low-humidity (L/L) environment correction for the fusing temperature
setting of each paper (SIM43-04).
setting of each paper (SIM43-04).
44
1
Used to set each correction operation function in the image forming (process) section.
Image process (Photoconductor/
Developing/Transfer/Cleaning)
Developing/Transfer/Cleaning)
9
Used to display the result data of the high density process control operation.
Image process (Photoconductor/
Developing/Transfer/Cleaning)
Developing/Transfer/Cleaning)
14
Used to display the output level of the temperature and humidity sensor.
Process (OPC drum,
development)/Fusing/LSU
development)/Fusing/LSU
43
Used to display the identification information of the developing unit.
Developing system
46
2
Used to adjust the copy density in the copy mode.
4
Used to adjust the density in the image send mode.
5
Used to adjust the density in the image send mode.
8
Used to adjust the image send mode color balance RGB.
9
Used to adjust the scan image density.
19
Used to set the operating conditions for the density scanning (exposure) of monochrome auto copy mode
documents.
documents.
30
Used to adjust the resolution in the sub scanning direction in the copy mode.
32
Used to adjust the document background density reproducibility in the monochrome auto copy mode.
37
Used to adjust the reproduction capability of monochrome mode color.
39
Used to adjust the sharpness of FAX send images.
40
Used to adjust the FAX send image density. (Collective adjustment of all the modes)
41
Used to adjust the FAX send image density. (Normal)
42
Used to adjust the FAX send image density. (Fine)
43
Used to adjust the FAX send image density. (Super Fine)
44
Used to adjust the FAX send image density. (Ultra fine)
45
Used to adjust the FAX send image density. (600dpi).
47
Used to set the compression rate of copy and scan images (JPEG).
60
Used to adjust the sharpness in the color auto copy mode.
61
Used to adjust the area separation recognition level.
62
Used to set the operating conditions of the ACS, the area separation, the background image process, and
the auto exposure mode.
the auto exposure mode.
63
Used to adjust the density in the copy low density section.
48
1
Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning
direction).
direction).
5
Used to correction the scan image magnification ratio (in the sub scanning direction).
Scanner section
6
Used to adjust the rotation speed of each motor.
49
1
Used to perform the firmware update.
3
Used to update the operation manual in the HDD.
5
Used to perform the watermark update.
50
1
Copy image position, image loss adjustment
2
Used to adjust the copy image position and the image loss. (This simulation is a simplified version of SIM
50-1.)
50-1.)
5
Used to adjust the print lead edge image position. (PRINTER MODE)
6
Used to adjust the copy image position and the image loss. (RSPF mode)
RSPF
7
Used to adjust the copy image position and the image loss (RSPF mode).
(This simulation is a simplified version of SIM 50-6.)
(This simulation is a simplified version of SIM 50-6.)
RSPF
10
Used to adjust the black print image magnification ratio and the off-center position.
(The adjustment is made separately for each paper feed section.)
(The adjustment is made separately for each paper feed section.)
12
Used to perform the scan image off-center position adjustment.
(The adjustment is made separately for each scan mode.)
(The adjustment is made separately for each scan mode.)
27
Used to perform the image loss adjustment of scanned images in the FAX or image send mode.
28
Used to automatically adjust the image loss, void area, image off-center, and image magnification ratio.
51
2
Used to adjust the contact pressure (deflection amount) on paper by the main unit and the RSPF
registration roller. (This adjustment is performed when there is a considerable variation in the print image
position on the paper or when paper jams frequently occur.)
registration roller. (This adjustment is performed when there is a considerable variation in the print image
position on the paper or when paper jams frequently occur.)
9
Used to adjust the ON/OFF timing of the separation voltage.
53
6
Used to adjust the detection level of the RSPF document width.
7
Used to adjust the RSPF document size width sensor.
8
Used to adjust the document lead edge reference and the RSPF mode document scan position.
55
1
Used to set the specifications of the engine control operations. (SOFT SW)
2
Used to set the specifications of the scanner control operation. (SOFT SW)
3
Used to set the specifications of the controller operation. (SOFT SW)
10
Used to set the special stamp text. (Taiwan only)
Main
Sub
Functions
Section
5
‘16/Apr
5
MX-M264U SIMULATION 6 – 6
56
1
Used to transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.)
2
Used to backup the data in the EEPROM. SD Card, and HDD (including user authentication data and
address data) to the USB memory. (Corresponding to the device cloning and the storage backup.)
address data) to the USB memory. (Corresponding to the device cloning and the storage backup.)
3
Used to backup the document filing data to the USB memory.
4
Used to backup the JOB log data to the USB memory.
5
Used to import the SIM22-6 data to a USB memory in the TEXT format.
11
Used to save the data in the SD card to the HDD temporarily.
12
Used to copy the SD card data saved temporarily in the HDD with SIM56-11 to the machine.
60
1
Used to check the memory operations (read/write) of the MFP PWB.
61
1
Used to check the LSU polygon motor rotation and laser detection.
LSU
3
Used to set the laser power
62
1
Used to format the hard disk. (HDD: Excluding the Operation manual and the watermark data)
2
Used to check read/write of the hard disk (partial).
3
Used to check read/write of the hard disk (all areas).
6
Used to perform the self diagnostics of the hard disk.
7
Used to print the hard disk self diagnostics error log.
8
Used to format the hard disk. (HDD: Excluding the Operation Manual, the watermark data, and the system
area)
area)
10
Used to clear the job completion list data.
11
Used to delete the document filing data.
12
Used to set Enable/Disable of auto format in a hard disk trouble.
13
Used to format the hard disk. (Operation Manual, watermark data only)
14
Used to initialize (remake) only the database file of the HDD.
HDD
63
1
Used to display the shading correction result.
Scanner
2
Used to perform shading.
3
Used to perform scanner (CCD) color balance and gamma auto adjustment.
Scanner
4
Used to display the SIT chart patch density.
5
Used to perform the scanner (CCD) color balance and gamma default setting.
64
2
Test print. (Self print) (Monochrome mode)
4
Printer test print. (Self print)
5
Printer test print. (Self print) (PCL)
6
Printer test print. (Self print) (PS)
65
1
Used to adjust the touch panel (LCD display section) detection coordinates.
Operation panel section
2
Used to display the touch panel (LCD display section) detection coordinates.
5
Used to check the operation panel key input.
66
1
Used to display the FAX-related soft SW (2 - 150) on the LCD to allow changing the soft SW while checking
with the LCD.
with the LCD.
FAX
2
Used to enter a country code and set the default value for the country code.
FAX
3
Used to check read/write of the EEPROM and the SDRAM on the MODEM controller and display the result.
FAX
4
Used to send the selected signals to the line and the main unit speaker. (Send level: max.)
FAX
5
Used to send the selected signal to the line and the main unit speaker. (Send level: Soft SW setting)
(For the kinds of send signals, refer to SIM66-04.)
(For the kinds of send signals, refer to SIM66-04.)
FAX
6
Used to print the confidential registration check table (BOX NO., BOX name, passcode.
(If there is no confidential registration, no print is made.)
(If there is no confidential registration, no print is made.)
FAX
7
Used to output all image data saved in the image memory. (Confidential data are also outputted.)
FAX
8
Used to send the selected sound messages to the line and the speaker. (Send level: Max.)
FAX
9
Used to send the selected sound message to the line and the speaker. (Send level: Soft SW setting)
* For details of sound messages, refer to the sound message table of SIM66-08.
* For details of sound messages, refer to the sound message table of SIM66-08.
FAX
10
Used to clear the FAX and image send image data. (The confidential data are also cleared.)
FAX
11
Used to send the selected signal at 300bps to the line and the speaker. (Send level: Max.)
FAX
12
Used to send the selected signal at 300bps to the line and the speaker. (Send level: Soft SW setting)
* For the kings of send signals at 300bps, refer to SIM66-11, 300bps send signal table.
* For the kings of send signals at 300bps, refer to SIM66-11, 300bps send signal table.
FAX
13
Used to register dial numbers for SIM66-14/15/16, Dial test. (Up to 20 digits can be registered.)
FAX
14
Used to execute the dial pulse (10PPS) send test and to adjust the make time.
FAX
15
Used to execute the dial pulse (20PPS) send test and to adjust the make time.
FAX
16
Used to execute the DTFM signal send test and to adjust the send level.
FAX
17
Used to send the DTMF signal to the line and the speaker. (Send level: Max.)
FAX
18
Used to send the DTMF signal to the line and the speaker. (Send level: Soft SW setting)
FAX
21
Used to print the selected items (system error, protocol monitor).
FAX
22
Used to set the handset sound volume. (This simulation can be executed even though the handset setting
is set to NO. When, however, the handset is not installed, the sound volume cannot be checked.)
(Japan model only)
is set to NO. When, however, the handset is not installed, the sound volume cannot be checked.)
(Japan model only)
FAX
24
Used to clear the FAST save data.
FAX
29
Used to initialize the telephone book data (the one-touch registration table, the FTP/Desktop expansion
table, the group expansion table, the program registration table, the interface memory box table, the meta
data, InboundRouting, and the DocumentAdmin table).
table, the group expansion table, the program registration table, the interface memory box table, the meta
data, InboundRouting, and the DocumentAdmin table).
FAX
30
Used to display the TEL/LIU status change, The display is highlighted by status change.
FAX
31
Used to set ON/OFF the port for output to TEL/LIU.
FAX
32
Used to check the fixed data received from the line and to display the result.
FAX
33
Used to execute detection of various signals with the line connected and to display the detection result.
When a signal is detected, the display is highlighted.
When a signal is detected, the display is highlighted.
FAX
Main
Sub
Functions
Section
MX-M264U SIMULATION 6 – 7
4. Details of simulation
1
1-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the scanner
(reading) unit and the control circuit.
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1)
Select the operation speed with the touch panel key.
2)
Press [EXECUTE] key.
Scanning is once performed at the speed corresponding to the
scan resolution (operation speed).
scan resolution (operation speed).
1-2
Purpose
Operation test/check
Function (Purpose)
Used to check the sensors in the scanner
(reading) section and the related circuits.
(reading) section and the related circuits.
Section
Scanner (reading)
Operation/Procedure
The operating status of the sensor is displayed.
When "MHPS" is highlighted, the scanner unit is in the home posi-
tion.
tion.
1-5
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the scanner
(reading) unit and the control circuit.
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1)
Select the operation speed with the touch panel key.
2)
Press [EXECUTE] key.
Scanning is repeated at the speed corresponding to the scan
resolution (operation speed).
resolution (operation speed).
When [EXECUTE] key is pressed, the operation is terminated.
2
2-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the auto-
matic document feeder and the control cir-
cuit.
matic document feeder and the control cir-
cuit.
Section
RSPF
Operation/Procedure
1)
Select the operation mode and the speed with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The RSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).
ations at the speed corresponding to the scan resolution (oper-
ation speed).
When [EXECUTE] key is pressed, the operation is terminated.
66
34
Used to execute the send test and display the time required for sending image data in the test. Used to
execute send test and display. (Unit: ms)
execute send test and display. (Unit: ms)
FAX
36
Used to check send and receive data from the MODEM controller to the MFP controller or the data line or
the command line individually.
the command line individually.
FAX
39
Used to check and change the destination setting saved in EEPROM of the FAX BOX.
FAX
42
Used to rewrite the program to power control installed in the FAX BOX.
FAX
43
Used to write the adjustment value into the power control installed in the FAX BOX.
FAX
61
Used to display the FAX-related soft SW (151 - 250) on the LCD to allow changing the soft SW while
checking with the LCD.
checking with the LCD.
FAX
62
Used to import the FAX receive data into a USB memory in PDF file type.
FAX
67
17
Printer reset
Printer
45
Used to adjust the printer image filter and trapping.
Printer
Main
Sub
Functions
Section
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI
(346.0mm/s)
(346.0mm/s)
300DPI
(346.0mm/s)
(346.0mm/s)
400DPI
400DPI
(259.5mm/s)
(259.5mm/s)
600DPI
600DPI
(173.0mm/s)
(173.0mm/s)
1200DPI
1200DPI
(86.5mm/s)
(86.5mm/s)
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI
(346.0mm/s)
(346.0mm/s)
300DPI
(346.0mm/s)
(346.0mm/s)
400DPI
400DPI
(259.5mm/s)
(259.5mm/s)
600DPI
600DPI
(173.0mm/s)
(173.0mm/s)
1200DPI
1200DPI
(86.5mm/s)
(86.5mm/s)
Item/Display
Operation mode
Default value
(SINGLE)
300DPI
300DPI
(259.5mm/s)
(259.5mm/s)
300DPI
(259.5mm/s)
(259.5mm/s)
400DPI
400DPI
(259.5mm/s)
(259.5mm/s)
600DPI
600DPI
(173.0 mm/s)
(173.0 mm/s)
(DOUBLE)
300DPI
300DPI
(259.5mm/s)
(259.5mm/s)
300DPI
(259.5mm/s)
(259.5mm/s)
400DPI
400DPI
(259.5mm/s)
(259.5mm/s)
600DPI
600DPI
(173.0 mm/s)
(173.0 mm/s)
Click on the first or last page to see other MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man7) service manuals if exist.