Sharp MX-FX10 Service Manual ▷ View online
MX-FX10 SIMULATIONS, FAX SOFTWARE SWITCH 4-11
66
32
Receive data check
Used to check receive data from the line and judge whether the following receive data and the judged data
number accord together or not. If they accord, "OK" is notified. If not, "NG" is notified. Judgment is made
from the receive start data and the data must be accorded continuously.
Used to check receive data from the line and judge whether the following receive data and the judged data
number accord together or not. If they accord, "OK" is notified. If not, "NG" is notified. Judgment is made
from the receive start data and the data must be accorded continuously.
33
Signal detection check
Used to detect signals and display the result with ON/OFF.
Used to detect signals and display the result with ON/OFF.
34
Communication time measurement
Used to perform a send/receive test and measure and display the time required for send/receive of the
image data in the communication.
Used to perform a send/receive test and measure and display the time required for send/receive of the
image data in the communication.
Main
code
code
Sub
code
Contents
Remark
Sim66-32 RECV DATA
[OK] key
Sim66-32 RECV DATA
Sim66-32 RECV DATA
CHECK RECEIVE DATA
EXEC
RESULT
XX
After pressing
[OK] key,
during
execution
[OK] key,
during
execution
RECEIVING
EXEC
Simulation code input window
"RECEIVING" is displayed
only during receive.
only during receive.
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
[OK] key
[OK] key
: Settlement
[START] key
: Settlement
[BACK] key : Simulation code input window
[C] key
[C] key
: Disable
XX
: "OK/NG" is displayed
Completion of
execution
(Highlighted
during execution)
execution
(Highlighted
during execution)
[BACK] key
CI : FNET:
EXEC
Sim66-33 SIGNAL CHK
CNG : CED :
BT : DT :
BT : DT :
EXEC
Sim66-33 SIGNAL CHK
1:CI FNET
2:CNG CED BT DT
3:Flag SDT DTMF
(1 - 3)
2:CNG CED BT DT
3:Flag SDT DTMF
(1 - 3)
X
Sim66-33 SIGNAL CHK
Flag: SDT :
DTMF:
DTMF:
EXEC
[OK] key
[OK] key
[BACK] key
[OK] key
[BACK] key
[OK] key
[BACK] key
Sim66-33 SIGNAL CHK
CI :OFF FNET:OFF
DETECT
EXEC
Sim66-33 SIGNAL CHK
CNG :OFF
CED :OFF
BT :OFF
DT :OFF
DETECT
EXEC
Sim66-33 SIGNAL CHK
Flag:OFF SDT :OFF
DTMF:OFF
DTMF:OFF
DETECT
EXEC
Sim66-33 SIGNAL CHK
After selection with numeric key
After pressing [OK] key,
during execution
during execution
After pressing [OK] key,
during execution
during execution
After pressing [OK] key,
during execution
during execution
SIM66-33 initial window
SIM66-33 initial window
SIM66-33 initial window
1:CI FINET
2:CNG CED BT DT
3:Flag SDT DTMF
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
[C] key
[C] key
: Input clear
Numeric key
: Item selection
[ON] key
: Input value settlement and execution
[START] key
: Similar to OK key
Signal detection
YES/NO is displayed
with ON/OFF.
YES/NO is displayed
with ON/OFF.
Signal detection
YES/NO is displayed
with ON/OFF.
YES/NO is displayed
with ON/OFF.
Signal detection
YES/NO is displayed
with ON/OFF.
YES/NO is displayed
with ON/OFF.
Sim66-34 COMM. TIME
[OK] key
[BACK] key
Sim66-34 COMM. TIME
EXEC
COMM. TIME:
xxx:xx:xx:xxxms
Simulation code input window
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
[OK] key
[OK] key
: Settlement
[BACK] key
: Simulation code input windo
[START] key
: Settlement
[C] key
: Disable
Immediately after pressing [OK] key,
the window shifts to the next one.
the window shifts to the next one.
MX-FX10 SIMULATIONS, FAX SOFTWARE SWITCH 4-12
66
37
Speaker sound volume adjustment
Used to send the following test sounds to the line and the speaker to perform the adjustment of the sound
variation and the sound volume.The send level to the line is determined by the soft SW set value. The
selected sound variation and the sound volume are written into the corresponding soft SW.
Used to send the following test sounds to the line and the speaker to perform the adjustment of the sound
variation and the sound volume.The send level to the line is determined by the soft SW set value. The
selected sound variation and the sound volume are written into the corresponding soft SW.
Main
code
code
Sub
code
Contents
Remark
Sim66-37 SPEAKER
Sim66-37 SPEAKER
[OK] key
[OK] key
[OK] key
[OK] key
[OK] key
[OK] key
[OK] key
[OK] key
Sim66-37 SPEAKER
1:RINGER
2:LINE MONITOR
3:ON HOOK
( 1 - 6 )
2:LINE MONITOR
3:ON HOOK
( 1 - 6 )
X
ON HOOK SMA.
1:SMA.-1 3:LAR.-3
2:MED.-2 4:DF VOL.
( 1 - 4 )
1:SMA.-1 3:LAR.-3
2:MED.-2 4:DF VOL.
( 1 - 4 )
X
ON HOOK
SMALL -1
PRESS BACK TO STOP
SMALL -1
PRESS BACK TO STOP
EXEC
Sim66-37 SPEAKER
4:SCAN FINISH
5:TX/RX FINISH
6:DTMF
( 1 - 6 )
5:TX/RX FINISH
6:DTMF
( 1 - 6 )
X
Sim66-37 SPEAKER
ON HOOK
1:SMA.2:MED.3:LAR.
1:SMA.2:MED.3:LAR.
( 1 - 3 )
X
Select
"4: DEFAULT VOL."
"4: DEFAULT VOL."
A sound is delivered while EXEC is highlighted.
Ringing until [BACK]
key is pressed.
key is pressed.
After completion, the display
shifts to SIM66-37 window.
shifts to SIM66-37 window.
Sim66-37 SPEAKER
ON HOOK
SMALL -1
1 2 3 4 5 6 7
( 1 - 3 )
SMALL -1
1 2 3 4 5 6 7
( 1 - 3 )
X
Sim66-37 SPEAKER
ON HOOK
SMALL -1
PRESS BACK TO STOP
SMALL -1
PRESS BACK TO STOP
EXEC
Ringing while EXEC is displayed.
Ringing until RETURN key is pressed.
Ringing until RETURN key is pressed.
Mute setting available
Sim66-37 SPEAKER
Sim66-37 SPEAKER
Sim66-37 SPEAKER
1:RINGER
2:LINE MONITOR
3:ON HOOK
( 1 - 6 )
2:LINE MONITOR
3:ON HOOK
( 1 - 6 )
X
LINE MONITOR SMA.
1:SMA.-1 3:LAR.-3
2:MED.-2 4:DF VOL.
( 1 - 5 )
1:SMA.-1 3:LAR.-3
2:MED.-2 4:DF VOL.
( 1 - 5 )
X
LINE MONITOR
SMALL -1
PRESS BACK TO STOP
SMALL -1
PRESS BACK TO STOP
EXEC
Sim66-37 SPEAKER
4:SCAN FINISH
5:TX/RX FINISH
6:DTMF
( 1 - 6 )
5:TX/RX FINISH
6:DTMF
( 1 - 6 )
X
Sim66-37 SPEAKER
LINE MONITOR SMA.
5:NON
5:NON
( 1 - 5 )
X
Ringing while EXEC is displayed
Ringing while EXEC is displayed
After completion, the display shifts
to SIM66-37 initial window.
to SIM66-37 initial window.
Sim66-37 SPEAKER
LINE MONITOR
1:SMA.2:MED.3:LAR.
1:SMA.2:MED.3:LAR.
( 1 - 3 )
X
Sim66-37 SPEAKER
LINE MONITOR
SMALL -1
PRESS BACK TO STOP
SMALL -1
PRESS BACK TO STOP
EXEC
3sec later
3sec later
When "4: DEFAULT VOL" is selected
Sim66-37 SPEAKER
LINE MONITOR
SMALL -1
1 2 3 4 5 6 7
( 1 - 3 )
SMALL -1
1 2 3 4 5 6 7
( 1 - 3 )
X
"NO SOUND" cannot be set for DTMF, either.
After setting "DEFAULT VOL,"
ON HOOK
SMALL
SMALL
[BACK] key
ON HOOK
1: SMA. 2: MED. 3: LAR
1: SMA. 2: MED. 3: LAR
[BACK] key
Returns to
ON HOOK
1: SMA -2
2: MED.-4
3: LAR -7
4: DEFAULT VOL.
ON HOOK
1: SMA -2
2: MED.-4
3: LAR -7
4: DEFAULT VOL.
[BACK] key
[BACK] key
[BACK] key
[BACK] key
[BACK] key
[BACK] key
After selection with numeric keys
After selection
with numeric key
with numeric key
After selection with numeric key
After selection
with numeric key
with numeric key
After selection
with numeric key
with numeric key
After selection with numeric key
After selection with
numeric key
numeric key
After selection
with numeric key
with numeric key
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
[C] key
[C] key
: Input clear
keys
: Page switch
Numeric key
: Item selection, sound volume selection
[OK] key
: Settlement and execution.
After completion, a sound rings for several
seconds and the display shift to the selection
window.
seconds and the display shift to the selection
window.
[START] key
: Input value settlement
[BACK] key
: Returns to the selection window.
MX-FX10 SIMULATIONS, FAX SOFTWARE SWITCH 4-13
66
38
Time setting/check
Used to write/read the time (year, month, day, o'clock, minute) into/from the RTC on the FAX PWB.
Used to write/read the time (year, month, day, o'clock, minute) into/from the RTC on the FAX PWB.
41
CI signal check
Used to detect the call signal from CI pin and send the call sound to the line and the speaker. The sound
volume of the call sound follows the soft SW setting. The operations of signal detection and the pseudo ring
sound send when the signal is detected are continued until the interruption command is made by pressing
RETURN key.
Used to detect the call signal from CI pin and send the call sound to the line and the speaker. The sound
volume of the call sound follows the soft SW setting. The operations of signal detection and the pseudo ring
sound send when the signal is detected are continued until the interruption command is made by pressing
RETURN key.
52
Pseudo ringer check
• The pseudo ringer sound is delivered both from the machine (speaker).
• This operation is continued until the interruption command is made by pressing RETURN key.
• The LCD displays the TEL/LIU status and the HOOK status.
• While the pseudo ringer is delivered, the RBT )ring back tone) is delivered to the line. The bell is ON for
• The pseudo ringer sound is delivered both from the machine (speaker).
• This operation is continued until the interruption command is made by pressing RETURN key.
• The LCD displays the TEL/LIU status and the HOOK status.
• While the pseudo ringer is delivered, the RBT )ring back tone) is delivered to the line. The bell is ON for
1sec and OFF for 2sec.
Main
code
code
Sub
code
Contents
Remark
Sim66-38 DATE & TIME
Sim66-38 DATE & TIME
Sim66-38 DATE & TIME
Sim66-38 DATE & TIME
Sim66-38 DATE & TIME
DATE
YEAR
YEAR
XXXX
(2004-2062)
YY
DATE
MONTH
MONTH
XX
(1-12)
YY
DATE
DAY
DAY
XX
(1-31)
YY
TIME
XX:XX
(00-23)
YY
YEAR
20YY
MONTH
YY
DAY
YY
EXEC
After execution, the display shifts
to the sub code input window.
to the sub code input window.
After inputting
with numeric
key, press
[OK] key.
with numeric
key, press
[OK] key.
[OK] key
[OK] key
After inputting
with numeric
key, press
[OK] key.
with numeric
key, press
[OK] key.
[OK] key
[OK] key
After inputting
with numeric
key.
with numeric
key.
After inputting
with numeric
key.
with numeric
key.
[OK] key
After inputting
with numeric
key.
with numeric
key.
[OK] key
Sim66-38 DATE & TIME
TIME
XX:XX
(00-59)
YY
xx: The current year/month/day
is displayed.
yy: The input value is displayed.
is displayed.
yy: The input value is displayed.
xx: The current time is displayed.
yy: The input value is displayed.
yy: The input value is displayed.
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
Numeric keys
Numeric keys
: Item selection and time input
[OK] key
: Settlement
[START] key : Settlement
[BACK] key : Returns to the previous window or
[BACK] key : Returns to the previous window or
the simulation code input window.
[C] key
: Input value clear
Sim66-41 CI SIGNAL
[OK] key
Sim66-41 CI SIGNAL
CHECK CI SIGNAL
EXEC
After pressing
[OK] key, during
execution
[OK] key, during
execution
CI:OFF
PRESS BACK TO STOP
PRESS BACK TO STOP
EXEC
When RETUREN key is pressed,
the window shifts to SIM66-41
input window.
the window shifts to SIM66-41
input window.
When detected,
OFF is changed to ON.
OFF is changed to ON.
When [BACK] key is pressed
during detection,the display
shifts to SIM66-41 input window.
during detection,the display
shifts to SIM66-41 input window.
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
[OK] key
[OK] key
: Settlement
[BACK] key
: Returns to the simulation
code input window.
[BACK] key
[BACK] key
Sim66-52 PSEUDO RNG
Sim66-52 PSEUDO RNG
PSEUDO RINGER CHK
EXEC
After pressing
[OK] key, during
execution
[OK] key, during
execution
PSEUDO RINGER CHK
PRESS BACK TO STOP
PRESS BACK TO STOP
EXEC
SIM66-52 initial window
[CA] key
:Simulation cancel
[INTERRUPT] key :Sub code input window
[OK] key
[OK] key
:Execution
[BACK] key
:Returns to the selection window.
[START] key
:Execution
[C] key
: Disable
[BACK] key
[OK] key
MX-FX10 SIMULATIONS, FAX SOFTWARE SWITCH 4-14
5. FAX software switch
A. Software switch setup change quick reference
Large item
Medium item
Content of switch
System
settings
Soft SW No.
Purpose of use
Dial (Calling)
Remote
machine
calling disable
machine
calling disable
Polarity inversion monitor during call-out
-
SW 23-3
Dial disable
Pause time setting
Inital setup
SW 28-1~4
Dial disable/Erroneous dialing
Tone/pulse default setting
-
SW 22-5,6
Dial disable
DTMF signal send time
-
SW 26-1~5
Dial disable in PB(PB/FAX service,etc.)
DTMF send MAX. level
-
SW 65-1~4
Dial disable in PB(PB/FAX service,etc.)
DTMF send level (High area)
-
SW 64-4~8
Dial disable in PB(PB/FAX service,etc.)
DTMF send level(Difference between high
area and low area)
area and low area)
-
SW 65-5~8
Dial disable in PB(PB/FAX service,etc.)
Minimum pause time (DTMF) setting
-
SW 26-6~8
Dial disable in PB(PB/FAX service,etc.)
Scanner scanning completion speaker sound
volume
volume
-
SW 46-1,2
Scanning sound volume pattern number
-
SW 46-3~8
Minimum pause time (10PPS) setting
-
SW 19-1~4
Dial disable in pulse
Minimum pause time (20PPS) setting
-
SW 19-6~8
Dial disable in pulse
Signal
detection
detection
Dial tone detection
-
SW 21-1
Dial tone detection disable
Busy tone detection
-
SW 21-2
Busy tone detection disable
Redial
Error
Number of resends in a communication error Send setup
SW 14-1~4
Error
Resend interval in a communication error
-
SW 14-5~8
Error(SG3)
Resend in case of an error, Super G3 disable
in the last call out
in the last call out
-
SW 43-2
Busy
Number of recalls when busy
Send setup
SW 13-1~4
Busy
Resend interval when busy
-
SW 13-5~8
Reception
(Calling)
(Calling)
CI detection
disable
disable
CI detection
-
SW 86-2,3
Not used
-
SW 86-6~8
CI signal OFF detection enable time
-
SW 87-1~7
External
telephone
handset
telephone
handset
External
telephone
connection
telephone
connection
External telephone connection
Inital setup
SW 41-1
External telephone connection
Remote switch number setting
-
SW 7-1~8
Remote switch detection error
Communication
General
Signal send level
-
SW 15-4~8
When the remote machine does not
receive signals in a proper level
receive signals in a proper level
Polarity inversion monitor during
communication
communication
-
SW 23-2
SG3
V.34 mode function
-
SW 43-1
Frequent errors in SG3 communication
Symbol speed mask in V.34 receive
-
SW 43-4~6
Frequent errors in SG3 communication
Send
G3/SG3
Countermeasures against echo in send (The
hold time until signal send is set after DIS
receive.)
hold time until signal send is set after DIS
receive.)
-
SW69-8
An error occurs in phase B
G3
Error process in RTN receive
-
SW73-1
OK is displayed when RTN is received
Receive
G3/SG3
CSI send
-
SW70-2
Max. length of receive
-
SW69-4
Substitute receive
-
SW9-1
SG3
Countermeasures against echo in receive
(CED tone send interval)
(CED tone send interval)
-
SW69-7
An error occurs in phase B in reception
Modem speed fixed in receive
-
SW16-5,6
EYE-Q check
-
SW72-7
Receive print
Paper
selection
selection
Paper selection priority order
-
SW35-2
Output condition setting
Receive
setup
setup
SW35-3,4
Automatic reduction print
-
SW35-1
Automatic reduction magnification ratio
-
SW 35-5~8
Rotation print
-
SW40-1
To disable rotation print
Click on the first or last page to see other MX-FX10 service manuals if exist.