Sharp MX-C380P / MX-C400P / MX-B380P / MX-B382P / MX-B400P (serv.man6) Service Manual ▷ View online
MX-C400P/C380P, MX-B400P/B380P/B382P SIMULATION 5 – 7
3. Details of simulation
3
3-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and the detectors in the finisher and
the control circuit.
the control circuit.
Section
Finisher
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
3-3
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1)
1)
Select the item to be operation checked.
2)
Select [EXECUTE] button, and press [OK] key.
The selected load performs the operation.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
The selected load performs the operation.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
62
1
Used to execute the hard disk format (except operation manual area).
2
Used to check read/write of the hard disk (partial).
3
Used to check read/write of the hard disk (all areas).
6
Used to perform the self diagnostics of the hard disk.
7
Used to print the hard disk self diagnostics error log.
8
Used to format the hard disk. (Excluding the system area and the operation manual area)
10
Used to delete the job log data.
11
Used to delete the print hold data (document filing data).
12
Used to set Enable/Disable of auto format in a hard disk trouble.
13
Used to format the hard disk. (only the operation manual area)
64
1
Test print. (Self print) (Color mode) (MX-C400P/C380P)
2
Test print. (Self print) (Monochrome mode)
4
Printer test print. (Self print) (256 gradations)
5
Printer test print. (Self print) (PCL)
6
Printer test print. (Self print) (PS)
7
Used to the test print. (Self print). (This function is not used in the market.)
65
5
Used to check the operation panel key input.
67
17
Used to reset the printer controller.
Printer
21
Printer color balance adjustment (Simplified adjustment) (MX-C400P/C380P)
Printer
22
Printer color balance adjustment (Manual adjustment)/Printer density and gradation adjustment (Manual
adjustment)
adjustment)
Printer
23
Used to print the printer color balance check sheet. (MX-C400P/C380P)
Printer
25
Printer color balance adjustment (Manual adjustment)/Printer density and gradation adjustment (Manual
adjustment)
adjustment)
Printer
30
Used to set Enable/Disable of printer calibration data transfer. (Though this simulation menu is displayed, it
does not work.)
does not work.)
Printer
31
Used to clear the printer calibration value.
Printer
33
Used to change the gamma of the printer screen. (for PCL/PS)
Printer
34
Used to set the density correction in the printer high density section. (Support for the high density section
tone gap)
tone gap)
Printer
36
Used to adjust the density in the low density section.
Printer
52
Used to reset the printer color balance adjustment (adjustment for each dither) to the default value. (The
set values of SIM67-33 is set to the default values.)
set values of SIM67-33 is set to the default values.)
70
MFP PWB SRAM data clear
MFP PWB
Main
Sub
Functions
Section
FPPD1
Finisher paper pass detector
FPLD
Finisher paper level detector
FDTULS
Finisher delivery tray upper limit sensor
FDTLLS
Finisher delivery tray lower limit sensor
FDRPS
Finisher delivery roller position sensor
FPRD-F
Finisher paper rear edge detector F
FPRD-C
Finisher paper rear edge detector C
FPRD-R
Finisher paper rear edge detector R
FAPHPS-F
Finisher paper alignment plate home position sensor F
FAPHPS-R
Finisher paper alignment plate home position sensor R
FSTPD
Finisher staple tray paper detector
FSHPS
Finisher staple home position sensor
FSED
Finisher staple empty detector
FSLD
Finisher staple lead detector
FSSW
Finisher safety switch
FPGS
Finisher paper gate solenoid
FPDM
Finisher paper delivery motor
FPS
Finisher paddle solenoid
FARLS
Finisher alignment roller lift solenoid
FPTM
Finisher paper transport motor
FDRLM
Finisher delivery roller lift motor
FPAM-F
Finisher paper alignment motor F
FPAM-R
Finisher paper alignment motor R
FSM
Finisher staple motor
FTLM
Finisher tray lift motor
FSCF
Finisher stapler cooling fan
FBCF
Finisher control board cooling fan
MX-C400P/C380P, MX-B400P/B380P/B382P SIMULATION 5 – 8
3-10
Purpose
Adjustment
Function (Purpose) Used to adjust the finisher.
Section
Section
Finisher
Operation/Procedure
1) Select a target item to be adjusted.
2) Set the set value. (Enter the set value, and press [OK] key and
1) Select a target item to be adjusted.
2) Set the set value. (Enter the set value, and press [OK] key and
OSA shortcut key.)
(The set value is saved.)
(The set value is saved.)
Item A:
• When the adjustment value is increased by 1, the alignment
• When the adjustment value is increased by 1, the alignment
plate F/R width is narrowed by 0.419mm in alignment operation.
• When the adjustment value is decreased by 1, the alignment
plate F/R width is widened by 0.419mm in alignment operation.
• The alignment plate F and the alignment plate R cannot be
adjusted separately. The shift amount on the F side and that on
the R side are alternatively corrected every time the adjustment
value is increased by 1. (Correction with 51 for the F side, and 52
for the R side. ... 59 for the F aide, and 60 for the R side. Similar
when the set value is decreased.)
the R side are alternatively corrected every time the adjustment
value is increased by 1. (Correction with 51 for the F side, and 52
for the R side. ... 59 for the F aide, and 60 for the R side. Similar
when the set value is decreased.)
Item B:
• When the adjustment value is increased by 1, the shift amount of
• When the adjustment value is increased by 1, the shift amount of
the paper delivery roller is changed by 0.11mm toward the pres-
sure increasing side (*1).
sure increasing side (*1).
• When the adjustment value is decreased by 1, the shift amount
of the paper delivery roller is changed by 0.11mm toward the
pressure decreasing side (*1).
*1:
The pressure increasing side means the direction to increase the
paper delivery roller pressure onto paper, and the pressure
decrease side means the direction to decrease the paper deliv-
ery roller pressure onto paper.
pressure decreasing side (*1).
*1:
The pressure increasing side means the direction to increase the
paper delivery roller pressure onto paper, and the pressure
decrease side means the direction to decrease the paper deliv-
ery roller pressure onto paper.
4
4-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the paper feed tray,
and the control circuit of those.
and the control circuit of those.
Section
Paper feed tray (Option)
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
4-3
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the loads
in the paper feed tray, and the control circuit
of those.
of those.
Section
Paper feed tray
Operation/Procedure
1)
1)
Select the load item that is required to operation check.
2)
Select [EXECUTE] button, and press [OK] key.
The selected load performs the operation.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
The selected load performs the operation.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
4-5
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the paper
feed tray unit paper transport clutch
(DTRC).
(DTRC).
Section
Paper feed tray unit
Operation/Procedure
(Check the ON operation)
Select the button of the code to be checked for the ON operation,
and press [OK] key.
Checking is started. When the operation is normal, the button on
the display is highlighted. When it is abnormal, the button is not
highlighted.
(Check the OFF operation)
Select the highlighted code button in the ON operation, and press
[OK] key.
When the operation is normal, the highlighted button on the display
returns to the normal display. When it is abnormal, the highlighted
display is maintained.
(Check the ON operation)
Select the button of the code to be checked for the ON operation,
and press [OK] key.
Checking is started. When the operation is normal, the button on
the display is highlighted. When it is abnormal, the button is not
highlighted.
(Check the OFF operation)
Select the highlighted code button in the ON operation, and press
[OK] key.
When the operation is normal, the highlighted button on the display
returns to the normal display. When it is abnormal, the highlighted
display is maintained.
Item/Display
Content
Setting
range
Default
value
A
FPAM ADJUST
Paper alignment width
adjustment *1
adjustment *1
40 - 60
50
B
FDRLM ADJUST
Paper delivery roller
descending position
adjustment
descending position
adjustment
40 - 60
50
D1PPD
Paper feed tray 2 paper transport detector
D1ULD
Paper feed tray 2 upper limit detector
D1PED
Paper feed tray 2 paper empty detector
D1PQD
Paper feed tray 2 paper remaining quantity detector
D1PRED1
Paper feed tray 2 paper rear edge detector 1
D1PRED2
Paper feed tray 2 paper rear edge detector 2
D1PRED3
Paper feed tray 2 paper rear edge detector 3
D1COCS
Paper feed tray 2 cover open/close sensor
D2MDC
Paper feed tray 3 installation detection connector
D2PPD
Paper feed tray 3 paper transport detector
D2ULD
Paper feed tray 3 upper limit detector
D2PED
Paper feed tray 3 paper empty detector
D2PQD
Paper feed tray 3 paper remaining quantity detector
D2PRED1
Paper feed tray 3 paper rear edge detector 1
D2PRED2
Paper feed tray 3 paper rear edge detector 2
D2PRED3
Paper feed tray 3 paper rear edge detector 3
D2COCS
Paper feed tray 3 cover open/close sensor
D3MDC
Paper feed tray 4 installation detection connector
D3PPD
Paper feed tray 4 paper transport detector
D3ULD
Paper feed tray 4 upper limit detector
D3PED
Paper feed tray 4 paper empty detector
D3PQD
Paper feed tray 4 paper remaining quantity detector
D3PRED1
Paper feed tray 4 paper rear edge detector 1
D3PRED2
Paper feed tray 4 paper rear edge detector 2
D3PRED3
Paper feed tray 4 paper rear edge detector 3
D3COCS
Paper feed tray 4 cover open/close sensor
DPFM
Transport motor
D1LM
Paper feed tray 1 lift-up motor
D1PFC
Paper feed tray 1 paper feed clutch
D1PTC
Paper feed tray 1 paper transport clutch
D2LM
Paper feed tray 2 lift-up motor
D2PFC
Paper feed tray 2 paper feed clutch
D2PTC
Paper feed tray 2 paper transport clutch
D3LM
Paper feed tray 3 lift-up motor
D3PFC
Paper feed tray 3 paper feed clutch
D3PTC
Paper feed tray 3 paper transport clutch
MX-C400P/C380P, MX-B400P/B380P/B382P SIMULATION 5 – 9
5
5-1
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the display,
LCD in the operation panel, and control cir-
cuit.
cuit.
Section
Operation panel
Operation/Procedure
The LCD is changed as shown below.
The contrast changes every 2sec from the current level to MAX
The LCD is changed as shown below.
The contrast changes every 2sec from the current level to MAX
MIN
the current level. During this period, each LED is lighted.
The LCD display contrast change and the LED lighting status are
checked.
checked.
5-2
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the heater
lamp and the control circuit.
Section
Fusing
Operation/Procedure
1) Select the item to be operation checked.
2) Select [EXECUTE] button, and press [OK] key.
1) Select the item to be operation checked.
2) Select [EXECUTE] button, and press [OK] key.
The selected heater lamp operates ON/OFF.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
• MX-C400P/C380P, MX-B400P/B380P
• MX-B382P
5-4
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the dis-
charge lamp and the control circuit.
Section
Process
Operation/Procedure
1)
1)
Select a target of the operation check.
When [ALL] button is pressed, all the items are selected.
When [ALL] button is pressed, all the items are selected.
2)
Select [EXECUTE] button, and press [OK] key.
The selected discharge lamp is lighted for 30 sec.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
The selected discharge lamp is lighted for 30 sec.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
6
6-1
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the load in
the paper transport system (clutches and
solenoids) and the control circuits.
solenoids) and the control circuits.
Section
Paper transport/Paper exit section
Operation/Procedure
1)
1)
Select the item to be operation checked.
2)
Select [EXECUTE] button, and press [OK] key.
The selected load performs the operation.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
The selected load performs the operation.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
Load operation check method:
The load operation is checked by the operation sound. However,
there are some loads which cannot be checked with the operation
sound.
• MX-C400P/C380P, MX-B400P/B380P
The load operation is checked by the operation sound. However,
there are some loads which cannot be checked with the operation
sound.
• MX-C400P/C380P, MX-B400P/B380P
* If two or more are selected at a time, it makes "Normal rotation."
HL_UM
Heater lamp upper (main)
HL_LM
Heater lamp lower (main)
HL_E
Heater lamp (external)
HL_UA
Heater lamp upper (all)
HL_UM
Heater lamp upper (main)
1
1
1
DL_K
Discharge lamp K
DL_C
Discharge lamp C
DL_M
Discharge lamp M
DL_Y
Discharge lamp Y
Section
Item/Display
Content
Transport/
process
RRM
Registration motor
POMF *
Paper exit motor (normal rotation)
POMR *
Paper exit motor (reverse rotation)
FUM
Fusing drive motor
CPFM
Paper feed motor
CPFC
Tray vertical transport clutch
HLPCS
Fusing pressure release/pressing
solenoid
solenoid
Paper feed
CLUM1
Paper feed tray 1 lift-up motor
CPUC1
Paper feed tray 1 paper feed clutch
MPFS
Manual paper feed solenoid
1
: ’11/Mar/15
1
MX-C400P/C380P, MX-B400P/B380P/B382P SIMULATION 5 – 10
• MX-B382P
* When it was chosen at the plural same time, about the thing that
“an original change
reversal” of the same load is displayed as
the other item, "original change" works.
In addition, I do not accept a turn to the opposite direction unless
I become the movement stop state when the load is turning.
In addition, I do not accept a turn to the opposite direction unless
I become the movement stop state when the load is turning.
6-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of each fan
motor and its control circuit.
Section
Others
Operation/Procedure
1) Select the item to be operation checked.
2) Select [EXECUTE] button, and press [OK] key.
1) Select the item to be operation checked.
2) Select [EXECUTE] button, and press [OK] key.
The selected load performs the operation.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
Press [ALL] button to select all the fans collectively.
With [EXECUTE] button selected, press [OK] key again, and
the simulation is terminated.
Press [ALL] button to select all the fans collectively.
Load operation check method:
The load operation is checked by the operation sound. However,
there are some loads which cannot be checked with the operation
sound.
The load operation is checked by the operation sound. However,
there are some loads which cannot be checked with the operation
sound.
6-3
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the primary
transfer unit and the control circuit.
Section
Process (Transfer)
Operation/Procedure
1) Select the operation mode.
2) Select [EXECUTE] button, and press [OK] key.
3) The transfer unit repeats operations in the mode selected in
1) Select the operation mode.
2) Select [EXECUTE] button, and press [OK] key.
3) The transfer unit repeats operations in the mode selected in
procedure 1.
During this operation, the transfer unit status (the operation mode
position) is displayed.
With [EXECUTE] button selected, press [OK] key again, and the
simulation is terminated.
position) is displayed.
With [EXECUTE] button selected, press [OK] key again, and the
simulation is terminated.
• MX-C400P/C380P
• MX-B400P/B380P/B382P
6-6
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the fusing
separation.
Section
Fusing
Operation/Procedure
1)
1)
Select [EXECUTE] button, and press [OK] key.
2)
Fusing pressure applying and fusing pressure release are
repeated.
repeated.
During this period, the status of the fusing roller pressure is dis-
played.
With [EXECUTE] button selected, press [OK] key again, and the
simulation is terminated.
played.
With [EXECUTE] button selected, press [OK] key again, and the
simulation is terminated.
Section
Item/Display
Content
Transport/
process
RRM
Registration motor
POMF *
Paper exit motor (normal rotation)
POMR *
Paper exit motor (reverse rotation)
FUM
Fusing drive motor
CPFM
Paper feed motor
CPFC
Tray vertical transport clutch
Paper feed
CLUM1
Paper feed tray 1 lift-up motor
CPUC1
Paper feed tray 1 paper feed clutch
MPFS
Manual paper feed solenoid
Item/Display
Content
POFM
Paper exit cooling fan motor
PSFM
Power PWB cooling fan motor
LSUFM
LSU cooling fan motor
PROFM1
Process fan motor 1
PROFM2
Process fan motor 2
FUFM
Fusing cooling fan motor
HDDFM
HDD cooling fan motor
1
Mode
select key
Display
Transfer
mode
Operation
TC1
BLACK
Black mode
position
position
The switching
operations are
repeated as
follows: Black
mode position
operations are
repeated as
follows: Black
mode position
Color mode
position
position
Black
mode position
Drum separation
position
position
Primary
transfer
(Normal
rotation of the
mode select
gear)
transfer
(Normal
rotation of the
mode select
gear)
COLOR
Color mode
position
position
FREE
Drum
separation
position
separation
position
TC1_R
BLACK
Black mode
position
position
The switching
operations are
repeated as
follows: Black
mode position
operations are
repeated as
follows: Black
mode position
Drum separation
position
position
Color
mode position
Primary
transfer
(Reverse
rotation of the
mode select
gear)
transfer
(Reverse
rotation of the
mode select
gear)
FREE
Drum
separation
position
separation
position
COLOR
Color mode
position
position
TC2
PRINT
Print
position
position
The switching
operations are
repeated as
follows: Print
position
operations are
repeated as
follows: Print
position
Drum
separation
position
position
Secondary
transfer
(Driven by the
fusing motor)
transfer
(Driven by the
fusing motor)
FREE
Drum
separation
position
separation
position
Key
Display
Content
Remark
TC1
BLACK
Black mode
position
position
FREE
Drum
separation
position
separation
position
TC2
PRINT
Print
position
position
FREE
Drum
separation
position
separation
position
PRINT
Fusing pressure
applying
applying
Fusing pressure applying
Fusing
pressure release
(Fusing pressure
applying) The operation is repeated.
FREE
Fusing pressure
release
release
1
Black mode position
Drum separation position
The operation
is repeated.
Print position
Drum separation position
The operation
is repeated.
: ’11/Mar/15
1
Click on the first or last page to see other MX-C380P / MX-C400P / MX-B380P / MX-B382P / MX-B400P (serv.man6) service manuals if exist.