Sharp MX-BMX1 (serv.man2) Service Manual ▷ View online
Replacement Adjustment
20 October 2010
TR-3-25
3.2.10 STOP GATE CARRIAGE
AREA C
Removal
1. Before switching off the power,
1. Before switching off the power,
set the Trimmer (Paper size) to A4 / 8.5x11” and Trimming to off.
2. Remove Lower outfeed cover (
3.1.8).
3. Remove connectors [A] (
x2).
4. Remove connectors [B] (
x2).
5. Remove connector [C] (
x1).
6. Pull out the Carriage gently.
[A]
[B]
[C]
[D]
CAUTION
When removing the Carriage, watch out so the motor connectors [B] & [C]
do not get damaged by the side frame cut-outs.
do not get damaged by the side frame cut-outs.
Replacement
1. When positioning the carriage in place, make sure the two sliding rods and the
1. When positioning the carriage in place, make sure the two sliding rods and the
gear rack enters their holes and slot.
2. Reverse the removal procedure.
TR-3-26
20 October 2010
3.2.11 STOP GATE MOTOR M3 & SENSOR Q7
AREA C
Removal
1. Remove Stop gate carriage (
1. Remove Stop gate carriage (
3.2.10).
2. Remove nut [A] ( x1).
3. Remove Crank arm [B].
4. Remove screws [C] holding the motor ( x4).
5. Loosen set screw [D] ( x1).
3. Remove Crank arm [B].
4. Remove screws [C] holding the motor ( x4).
5. Loosen set screw [D] ( x1).
Replacement
1. Mount the Crank pulley [E] without tightening the set screw [D] ( x1).
2. Mount motor with screws [C] ( x4).
3. Mount Crank arm [B].
4. Tightening nut [A] ( x1).
1. Mount the Crank pulley [E] without tightening the set screw [D] ( x1).
2. Mount motor with screws [C] ( x4).
3. Mount Crank arm [B].
4. Tightening nut [A] ( x1).
NOTE: Make sure play for Crank arm [B] is maintained.
5. Position the Crank pulley [E] so it is aligned with Crank arm [B].
6. Tighten set screw [D] ( x1) on the flat of the shaft..
7. Reinstall Stop gate carriage (
6. Tighten set screw [D] ( x1) on the flat of the shaft..
7. Reinstall Stop gate carriage (
3.2.10).
[A]
[D]
[C]
[B]
[E]
Replacement Adjustment
20 October 2010
TR-3-27
3.2.12 LENGTH ADJUSTMENT MOTOR M4 & SENSOR Q12
AREA C
1. Remove Stop gate carriage (
3.2.10).
2. Unhook spring [A].
3. Remove screws [B] holding the motor ( x4).
3. Remove screws [B] holding the motor ( x4).
[A]
[B]
TR-3-28
20 October 2010
3.2.13 LENGTH ADJUSTMENT HOME POSITION SWITCH S11
AREA C
Removal
1. Remove Stop gate carriage (
1. Remove Stop gate carriage (
3.2.10).
2. Remove screws [B] ( x2).
3. Remove connectors [A] (
3. Remove connectors [A] (
x2).
Replacement
1. Reverse the removal procedure.
1. Reverse the removal procedure.
Adjustment
1. Place a ruler across the slide rods and up against the flange bushings
1. Place a ruler across the slide rods and up against the flange bushings
[Picture 1].
2. Position the switch so it is activated by the ruler and
so there is a 0.5 mm ± 0.2 mm gap between switch body and ruler [Picture 2].
3. Tighten screws [B] ( x2).
[A]
[B]
[Picture 1]
[Picture 2]
Click on the first or last page to see other MX-BMX1 (serv.man2) service manuals if exist.