Sharp MX-BMX1 (serv.man2) Service Manual ▷ View online
Replacement Adjustment
20 October 2010
TR-3-29
3.2.14 LOWER OUTFEED BELTS
AREA C
Removal
1. Remove Stop gate carriage (
1. Remove Stop gate carriage (
3.2.10).
2. Remove Paper path (
3.2.9).
3. Remove Transmission chain (
3.2.17).
4. Remove screws [A] ( x2).
5. Remove e-clip [B] ( x1).
6. Slide Flange bushing [C] towards the center of the shaft and tilt the shaft out
5. Remove e-clip [B] ( x1).
6. Slide Flange bushing [C] towards the center of the shaft and tilt the shaft out
through the cut-out in the side frame.
Replacement
1. Reverse the removal procedure.
1. Reverse the removal procedure.
Adjustment
1. Loosen screws [A] ( x2).
2. The belts should be adjusted so they have no slack and even tension.
3. Pull shaft [D] to obtain adjustment and tighten screws [B] ( x2).
1. Loosen screws [A] ( x2).
2. The belts should be adjusted so they have no slack and even tension.
3. Pull shaft [D] to obtain adjustment and tighten screws [B] ( x2).
[A]
[B]
[A]
[C]
[D]
TR-3-30
20 October 2010
3.2.15 UPPER OUTFEED BELTS
AREA C
Removal
1. Remove Belt stacker.
2. Remove Front and Rear cover (
1. Remove Belt stacker.
2. Remove Front and Rear cover (
3.1.1).
3. Remove Transmission chain (
3.2.17).
4. Unhook springs [A] (x2).
5. Remove screws [B] ( x6).
5. Remove screws [B] ( x6).
NOTE: Leave the screw at the top on each side
for the outfeed cover to pivot around.
6. Remove e-clip [C] ( x2).
Remove nylon washer [C] (x2).
Unhook link arm [D] (x2).
Remove needle bearing [C] (x2).
7. Remove e-clip [E] ( x2).
8. Pull out shaft [F].
9. Remove e-clips [G] ( x2) inside frames.
10. Slide Flange bushings [G] towards the center of
8. Pull out shaft [F].
9. Remove e-clips [G] ( x2) inside frames.
10. Slide Flange bushings [G] towards the center of
the shaft and pull out the whole assembly th-
rough the outfeed.
11. Loosen screws [H] ( x4) and remove belts.
Adjustment
1. The belts should be adjusted so they have no
1. The belts should be adjusted so they have no
slack and even tension.
2. Pull runner pulleys [I] to obtain adjustment and
tighten screws [H] ( x4).
Replacement
1. Reverse the removal procedure.
1. Reverse the removal procedure.
[E]
[H]
[I]
[F]
[A]
[D]
[C]
[G]
[C]
[G]
[A]
[D]
[C]
[C]
[G]
[B]
Replacement Adjustment
20 October 2010
TR-3-31
3.2.16 TRIM BIN FULL SENSOR Q8
AREA C
[A]
[B]
1. Undock the Trimmer.
2. Remove connector [A] (
2. Remove connector [A] (
x1).
3. Remove screw [B] ( x1).
TR-3-32
20 October 2010
3.2.17 TRANSMISSION CHAIN
AREA C
WARNING
Place the safety block [D] between lower knife and upper knife beam. When
removing the chain nothing holds upper knife beam and knife in position.
removing the chain nothing holds upper knife beam and knife in position.
[D]
[A]
[B]
[C]
1. Remove Front cover (
3.1.1).
2. Remove screws [A] ( x3).
3. Remove bracket [B].
4. Pull Tensioner [C] to release tension when removing chain.
3. Remove bracket [B].
4. Pull Tensioner [C] to release tension when removing chain.
Click on the first or last page to see other MX-BMX1 (serv.man2) service manuals if exist.