Sharp MX-BMX1 (serv.man2) Service Manual ▷ View online
Replacement Adjustment
20 October 2010
TR-3-13
3.2.3 CONTROL SWITCH S3
AREA C
Removal
1. Remove Rear cover (
1. Remove Rear cover (
3.1.1).
2. Remove connector [B] (
X2).
3. Remove screw [A] ( x2).
Replacement
1. Reverse the removal procedure.
1. Reverse the removal procedure.
Adjustment
1. Lift the compressing bracket.
2. Make sure the Switch activates approximately 10 mm from where the com-
1. Lift the compressing bracket.
2. Make sure the Switch activates approximately 10 mm from where the com-
pressing bracket latches in the upper position.
3. To adjust, loosen screws [A] ( x2 ).
4. Reposition switch to obtain adjustment.
5. Tighten screws [A] ( x2 ).
4. Reposition switch to obtain adjustment.
5. Tighten screws [A] ( x2 ).
[A]
[B]
TR-3-14
20 October 2010
3.2.4 TRANSPORT MOTOR M1
AREA C
[A]
[B]
1. Remove Transmission chain (
3.2.17).
2. Remove Knife support chain (
3.2.18).
3. Remove connector [A] (
x1).
4. Grab the inner sprocket to pull out the whole sprocket assembly [B].
5. Remove screws [C] holding the motor ( x3).
5. Remove screws [C] holding the motor ( x3).
NOTE: Hold the spacers between motor and frame when removing screws.
[C]
Replacement Adjustment
20 October 2010
TR-3-15
3.2.5 TRANSPORT BELT SENSOR Q4
AREA C
[A]
[B]
Removal
1. Remove Rear cover (
1. Remove Rear cover (
3.1.1).
2. Remove connector [A] (
x1).
3. Remove nut and screw [B] ( x1, x1).
4. Remove bracket [C].
5. Squeeze the barbs of the sensor to remove.
4. Remove bracket [C].
5. Squeeze the barbs of the sensor to remove.
Replacement
1. Reverse the removal procedure
1. Reverse the removal procedure
NOTE: When tightening nut/screw make sure there is a space between en-
coder disc and sensor.
2. Enter service program mode and start the belts (motor M1). Check speed (m/
s) is registered (
Service Manual MX-BMX1: 5.1.1, 5.1.2).
3. If no, or erratic speed, loosen screw/nut [B] ( x1, x1).
4. Reposition sensor to obtain correct speed registration.
5. Tighten screw/nut [B] ( x1, x1).
4. Reposition sensor to obtain correct speed registration.
5. Tighten screw/nut [B] ( x1, x1).
[C]
TR-3-16
20 October 2010
3.2.6 TRIM KNIFE MOTOR M2
AREA C
Removal
1. Remove Rear cover (
1. Remove Rear cover (
3.1.1).
2. Remove connector [E] (
x1).
3. Remove circlip [C] using a circlip plier.
4. Loosen screws [A] holding the motor ( x3).
5. Remove sprocket [F].
6. Remove screws [A] holding the motor ( x3).
4. Loosen screws [A] holding the motor ( x3).
5. Remove sprocket [F].
6. Remove screws [A] holding the motor ( x3).
Replacement
1. If it is difficult to mount sprocket [F] remove master link [B].
2. Reverse the removal procedure.
3. Tension the chain so there is no slack when tightening screws [A] ( x3).
1. If it is difficult to mount sprocket [F] remove master link [B].
2. Reverse the removal procedure.
3. Tension the chain so there is no slack when tightening screws [A] ( x3).
[B]
[A] [C]
[E]
[F]
WARNING
Place the safety block [D] between lower knife and upper knife beam. When
removing the chain nothing holds upper knife beam and knife in position.
removing the chain nothing holds upper knife beam and knife in position.
[D]
Click on the first or last page to see other MX-BMX1 (serv.man2) service manuals if exist.