Sharp MX-B381 / MX-B401 (serv.man7) Service Manual ▷ View online
MX-B381/B401 SIMULATION 5 – 56
46-9
Purpose
Adjustment (RSPF mode)
Function (Purpose) Used to adjust the scan image density.
Section
Section
Operation/Procedure
1)
1)
Select an adjustment target item with [
] [] key.
2)
Enter the set value with 10-key.
* When the key is pressed, the setting value of each
* When the key is pressed, the setting value of each
item can be changed with 1up (1down) collectively.
3)
Press [OK] key. (The set value is saved.)
This adjustment result affects the image send mode, the copy
mode, and the fax mode.
When the adjustment value is increased, the image density is
increased, and vice versa.
mode, and the fax mode.
When the adjustment value is increased, the image density is
increased, and vice versa.
46-16
Purpose
Adjustment
Function (Purpose) Used to adjust the copy density and the
gamma (for each copy mode).
Section
Operation/Procedure
1)
1)
Select an adjustment target item with [
] [] key.
2)
Enter the set value with 10-key.
* When the key is pressed, the setting value of each
* When the key is pressed, the setting value of each
item can be changed with 1up (1down) collectively.
3)
Press [EXECUTE] key, and the set value is saved and self
printing is made.
printing is made.
When the adjustment value is increased, the image density is
increased, and vice versa.
increased, and vice versa.
46-19
Purpose
Setting
Function (Purpose) Used to set the operating conditions for the
density scanning (exposure) of auto copy
mode documents.
mode documents.
Section
Operation/Procedure
Select an item to be set.
When an item is selected, it is highlighted and the setting change is
saved.
Select an item to be set.
When an item is selected, it is highlighted and the setting change is
saved.
Item/Display
Content
Default
value
A
LOW DENSITY POINT
Low density correction amount
50
B
HIGH DENSITY POINT
High density correction amount
50
Item/Display
Content
Setting
range
Default
value
A
COPY : LOW
RSPF copy mode exposure
adjustment (Low density side)
adjustment (Low density side)
1 - 99
45
B
SCAN : LOW
RSPF scanner mode exposure
adjustment (Low density side)
adjustment (Low density side)
1 - 99
45
C
FAX : LOW
RSPF FAX mode exposure
adjustment (Low density side)
adjustment (Low density side)
1 - 99
45
D
COPY : HIGH
RSPF copy mode exposure
adjustment (High density side)
adjustment (High density side)
1 - 99
48
E
SCAN : HIGH
RSPF scanner mode exposure
adjustment (High density side)
adjustment (High density side)
1 - 99
48
F
FAX : HIGH
RSPF FAX mode exposure
adjustment (High density side)
adjustment (High density side)
1 - 99
48
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(5&2/25%$/$1&($'-8670(17&2/256&$11(502'(
$˖
˷̚˹
˖/2:'(16,7<32,17
$˖
˖+,*+'(16,7<32,17
%˖
2.
%
*
5
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(1763)
$˖
˷̚˹
˖&23<˖/2:
$˖
˖6&$1˖/2:
%˖
˖)$;˖/2:
&˖
˖&23<˖+,*+
'˖
˖)$;˖+,*+
)˖
˖6&$1˖+,*+
(˖
2.
Item/Display
Density level
(Point)
Setting range
Default
value
A
POINT1
Point 1
373 - 627
500
B
POINT2
Point 2
373 - 627
500
C
POINT3
Point 3
373 - 627
500
D
POINT4
Point 4
373 - 627
500
E
POINT5
Point 5
373 - 627
500
F
POINT6
Point 6
373 - 627
500
G
POINT7
Point 7
373 - 627
500
H
POINT8
Point 8
373 - 627
500
I
POINT9
Point 9
373 - 627
500
J
POINT10
Point 10
373 - 627
500
K
POINT11
Point 11
373 - 627
500
L
POINT12
Point 12
373 - 627
500
M
POINT13
Point 13
373 - 627
500
N
POINT14
Point 14
373 - 627
500
O
POINT15
Point 15
373 - 627
500
P
POINT16
Point 16
373 - 627
500
Q
POINT17
Point 17
373 - 627
500
Item/Display
Content
Set value
Default
value
AE_MODE
Auto exposure mode
MODE1,
MODE2
MODE2
MODE1
AE_STOP_COPY
Auto B/W exposure
Stop (for copy)
Stop (for copy)
REALTIME/
STOP/
PRESCAN
STOP/
PRESCAN
STOP
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(*5$<%$/$1&(0$18$/$'-8670(17>$//%:@3*
$˖
˷̚˹
˖32,17
$˖
˖32,17
%˖
˖32,17
&˖
˖32,17
'˖
˖32,17
)˖
˖32,17
(˖
˖32,17
*˖
˖32,17
+˖
˖32,17
,˖
˖32,17
-˖
˖32,17
.˖
˖32,17
/˖
2.
(;(&87(
MX-B381/B401 SIMULATION 5 – 57
NOTE:
46-21
Purpose
Adjustment
Function (Purpose) Copy density and gradation adjustment
(Manual adjustment)
Section
Operation/Procedure
1)
1)
Use [
] [] keys to select a density level to be adjusted.
2)
Enter the set value with 10-key.
* When the key is pressed, the setting value of each
* When the key is pressed, the setting value of each
item can be changed with 1up (1down) collectively.
3)
Press [OK] key. (The set value is saved.)
When the adjustment value is increased, the image density is
increased, and vice versa.
When [EXECUTE] key is pressed, the check pattern in printed in
the density and gradation corresponding to the adjustment value.
increased, and vice versa.
When [EXECUTE] key is pressed, the check pattern in printed in
the density and gradation corresponding to the adjustment value.
46-23
Purpose
Adjustment/Setup
Function (Purpose) Used to set the density correction of copy
high density section (High density tone gap
supported).
supported).
Section
Operation/Procedure
1)
1)
Select an adjustment target item with [
] [] key.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
* When tone gap is generated in the high density area, set item A
to "0”.
The density of high density part decreases. However, the tone
gap is better.
The density of high density part decreases. However, the tone
gap is better.
* To increase the density in the high density area further, set item
A to "1”.
The tone gap may occur in high density part.
The tone gap may occur in high density part.
NOTE: Do not change the value of item B. If the value is changed,
the density in the high density area is changed.
AE_STOP_FAX
Auto B/W exposure
Stop (for FAX)
Stop (for FAX)
ON/OFF
ON
AE_STOP_SCAN
Auto B/W exposure
Stop (for scanner)
Stop (for scanner)
REALTIME/
STOP/
PRESCAN
STOP/
PRESCAN
STOP
AE_FILTER
Auto exposure filter
setting
setting
SOFT
NORMAL
NORMAL
SHARP
SHARP
AE_WIDTH
AE exposure width
FULL/PART
PART
MODE 1
High gamma (high contrast images)
MODE 2
Normal gamma
STOP
The image density in 3 - 7mm area at the lead edge is
scanned, and the output image density is determined
according to the scanned density. (The output image
density is even for all the surface.)
scanned, and the output image density is determined
according to the scanned density. (The output image
density is even for all the surface.)
REALTIME
The densities of the document width are scanned
sequentially, and the output image density is
determined according to the density in each area of
document. (The output image density may not be
even for all the surface.)
sequentially, and the output image density is
determined according to the density in each area of
document. (The output image density may not be
even for all the surface.)
PRESCAN
The densities of the all surface of document are
scanned sequentially, and the output image density is
determined according to the average of the scanned
densities. (The output image density is even for all the
surface.)
scanned sequentially, and the output image density is
determined according to the average of the scanned
densities. (The output image density is even for all the
surface.)
AE WIDTH FULL
The document density scan area in the monochrome
auto mode is 3 - 7mm at the document lead edge x
the document width. This is not related to the
PRESCAN mode.
auto mode is 3 - 7mm at the document lead edge x
the document width. This is not related to the
PRESCAN mode.
AE WIDTH PART
The document density scan area in the monochrome
auto mode is 3 - 7mm at the document lead edge x
100mm width. This is not related to the PRESCAN
mode.
auto mode is 3 - 7mm at the document lead edge x
100mm width. This is not related to the PRESCAN
mode.
Item/Display
Content
Set value
Default
value
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685(02'(6(783%:$(
02'(
02'(
$(B02'(
˖
5($/7,0(
35(6&$1
6723
$(B6723B&23<
˖
2))
21
$(B6723B)$;
˖
5($/7,0(
35(6&$1
6723
$(B6723B6&$1
˖
62)7
6+$53
1250$/
$(B),/7(5
˖
)8//
3$57
$(B:,'7+
˖
Item/Display
Density level
(Point)
Setting range
Default
value
A
POINT1
Point 1
245 - 755
500
B
POINT2
Point 2
245 - 755
500
C
POINT3
Point 3
245 - 755
500
D
POINT4
Point 4
245 - 755
500
E
POINT5
Point 5
245 - 755
500
F
POINT6
Point 6
245 - 755
500
G
POINT7
Point 7
245 - 755
500
H
POINT8
Point 8
245 - 755
500
I
POINT9
Point 9
245 - 755
500
J
POINT10
Point 10
245 - 755
500
K
POINT11
Point 11
245 - 755
500
L
POINT12
Point 12
245 - 755
500
M
POINT13
Point 13
245 - 755
500
N
POINT14
Point 14
245 - 755
500
O
POINT15
Point 15
245 - 755
500
P
POINT16
Point 16
245 - 755
500
Q
POINT17
Point 17
245 - 755
500
Item/Display
Content
Setting
range
Default
value
A
K
(0: ENABLE
1: DISABLE)
0
K engine highest density
correction mode: Enable
correction mode: Enable
0 - 1
1
1
K engine highest density
correction mode: Disable
correction mode: Disable
B
BLACK MAX
TARGET
Scanner target value for
BLACK maximum density
correction
BLACK maximum density
correction
0 - 999
500
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(*5$<%$/$1&(0$18$/$'-8670(17>$//&2/25@
$˖
˷̚˹
˖32,17
$˖
˖32,17
%˖
˖32,17
&˖
˖32,17
'˖
˖32,17
)˖
˖32,17
(˖
˖32,17
*˖
˖32,17
+˖
˖32,17
,˖
˖32,17
-˖
˖32,17
.˖
˖32,17
/˖
2.
(;(&87(
.
MX-B381/B401 SIMULATION 5 – 58
46-24
Purpose
Adjustment
Function (Purpose) Copy density and gradation adjustment
(Auto adjustment)
Section
Operation/Procedure
1)
1)
Press [EXECUTE] key.
The patch image (adjustment pattern) is printed out.
The patch image (adjustment pattern) is printed out.
2)
Plate the printed adjustment pattern on the document table.
3)
Press [EXECUTE] key.
The copy density and gradation adjustment is performed, then
the adjustment result pattern is printed.
The copy density and gradation adjustment is performed, then
the adjustment result pattern is printed.
4)
Press [OK] key.
The half tone correction target registration is processed.
The half tone correction target registration is processed.
46-32
Purpose
Adjustment/Setup
Function (Purpose) Used to adjust the document background
density reproducibility in the monochrome
auto copy mode.
auto copy mode.
Section
Operation/Procedure
1)
1)
Select a target item of setting with [
] [] key.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
When the adjustment value is increased, reproducibility of the
background and the low density image is increased. When the
adjustment value is decreased, reproducibility of the background
and the low density image is decreased.
background and the low density image is increased. When the
adjustment value is decreased, reproducibility of the background
and the low density image is decreased.
46-37
Purpose
Adjustment/Setup
Function (Purpose) Used to adjust the color document repro-
ducibility in the monochrome copy mode.
Section
Operation/Procedure
1)
1)
Select a target item with [
] [] keys.
2)
Enter the set value with 10-key.
3)
Press [EXECUTE] key.
4)
Press [YES] key.
This simulation is used to adjust the reproducibility of red and yel-
low images when copy a color document of red and yellow images
in the monochrome mode.
low images when copy a color document of red and yellow images
in the monochrome mode.
When [DEFAULT] key is pressed, it is set to the default value.
When the adjustment values of items A and B are decreased, the
copy density of yellow images is increased. When the adjustment
values are increased, the density is decreased.
When the adjustment value of item A is decreased and the adjust-
ment value of item B is increased, the copy density of red images is
increased. When the adjustment value of item A is increased and
the adjustment value of item B is decreased, the copy density is
decreased.
When the adjustment values of items A and B are decreased, the
copy density of yellow images is increased. When the adjustment
values are increased, the density is decreased.
When the adjustment value of item A is decreased and the adjust-
ment value of item B is increased, the copy density of red images is
increased. When the adjustment value of item A is increased and
the adjustment value of item B is decreased, the copy density is
decreased.
46-39
Purpose
Adjustment/Setup
Function (Purpose) Used to adjust the sharpness of FAX send
images.
Section
Operation/Procedure
1)
1)
Select a target item with [
] [] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
Item/Display
Content
Setting
range
Default
value
A
COPY : OC
Copy mode (for OC)
1 - 250
196
B
COPY : RSPF
Copy mode (for RSPF)
1 - 250
196
C
SCAN : OC
Scanner mode (for OC)
1 - 250
196
D
SCAN : RSPF
Scanner mode
(for RSPF)
(for RSPF)
1 - 250
196
E
FAX : OC
FAX mode (for OC)
1 - 250
196
F
FAX : RSPF
FAX mode (for RSPF)
1 - 250
196
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(0$;,080'(16,7<$'-8670(1702'(
$˖
˷̚˹
˖.˄(1$%/(ǂ˖',6$%/(˅
$˖
˖%/$&.ǂ0$;ǂ7$5*(7
%˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(+$/)721($872$'-8670(1702'(5(*8/$5
(;(&87(
35(66>(;(&87(@72352&21(;(&87,21$1'35,177+(7(673$7&+
3/($6(86(63(&,),('7<3(2)$25h6,=(3$3(5
)257+,6$'-8670(17
Item/Display
Content
Setting
range
Default
value
A
R-Ratio
Gray making setting (R)
0 - 1000
172
B
G-Ratio
Gray making setting (G)
0 - 1000
828
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
/,0,72)$(5($&7,216(77,1*
$˖
˷̚˹
˖&23<˖2&
$˖
˖&23<˖563)
%˖
˖6&$1˖2&
&˖
˖6&$1˖563)
'˖
˖)$;˖563)
)˖
˖)$;˖2&
(˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
% :,0$*(&5($7($'-8670(17%5DWLR
$˖
˷̚˹
˖55DWLR
$˖
˖*5DWLR
%˖
'()$8/7
$5(<28685("
<(6
12
(;(&87(
MX-B381/B401 SIMULATION 5 – 59
Input small numeric value to obtain crispy image. Input large
numeric value to decrease moire.
numeric value to decrease moire.
46-40
Purpose
Adjustment/Setup
Function (Purpose) Used to adjust the FAX send image density.
(Collective adjustment of all the modes)
Section
Operation/Procedure
1)
1)
Set the original on the original table.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
When [EXECUTE] key is pressed, the adjustment value is set
and the scanned document image is outputted.
When [EXECUTE] key is pressed, the adjustment value is set
and the scanned document image is outputted.
46-41
Purpose
Adjustment/Setup
Function (Purpose) Used to adjust the FAX send image density.
(Normal)
Section
Operation/Procedure
1)
1)
Set the original on the original table.
2)
Select a target item with [
] [] keys.
3)
Enter the set value with 10-key.
4)
Press [OK] key
When [EXECUTE] key is pressed, the adjustment value is set
and the scanned document image is outputted.
When [EXECUTE] key is pressed, the adjustment value is set
and the scanned document image is outputted.
To check the adjustment density level of items A - F, set the docu-
ment and set the setting value of item G according to items A - F,
and press [EXECUTE] key.
ment and set the setting value of item G according to items A - F,
and press [EXECUTE] key.
46-42
Purpose
Adjustment/Setup
Function (Purpose) Used to adjust the FAX send image density.
(Fine)
Section
Operation/Procedure
1)
1)
Set the original on the original table.
2)
Select a target item with [
] [] keys.
3)
Enter the set value with 10-key.
4)
Press [OK] key.
When [EXECUTE] key is pressed, the adjustment value is set
and the scanned document image is outputted.
When [EXECUTE] key is pressed, the adjustment value is set
and the scanned document image is outputted.
Item/Display
Content
Setting
range
Default
value
A
200 x 100 [DPI]
OFF
OFF
200 x 100 [DPI]
half tone OFF
half tone OFF
0 - 2
1
B
200 x 200 [DPI]
OFF
OFF
200 x 200 [DPI]
half tone OFF
half tone OFF
0 - 2
1
C
200 x 200 [DPI]
ON
ON
200 x 200 [DPI]
half tone ON
half tone ON
0 - 2
1
D
200 x 400 [DPI]
OFF
OFF
200 x 400 [DPI]
half tone OFF
half tone OFF
0 - 2
1
E
200 x 400 [DPI]
ON
ON
200 x 400 [DPI]
half tone ON
half tone ON
0 - 2
1
F
400 x 400 [DPI]
OFF
OFF
400 x 400[DPI]
half tone OFF
half tone OFF
0 - 2
1
G
400 x 400 [DPI]
ON
ON
400 x 400[DPI]
half tone ON
half tone ON
0 - 2
1
H
600 x 600 [DPI]
OFF
OFF
600 x 600[DPI]
half tone OFF
half tone OFF
0 - 2
1
I
600 x 600 [DPI]
ON
ON
600 x 600[DPI]
half tone ON
half tone ON
0 - 2
1
Item/Display
Content
Setting
range
Default
value
A
EXPOSURE
LEVEL(ALL)
LEVEL(ALL)
Used to adjust the FAX
send image density.
(Collective adjustment of all
the modes)
send image density.
(Collective adjustment of all
the modes)
1 - 99
50
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
,0$*(6(1'6+$531(66$'-8670(17
$˖
˷̚˹
˖h>'3,@2))
$˖
˖h>'3,@2))
%˖
˖h>'3,@21
&˖
˖h>'3,@2))
'˖
˖h>'3,@2))
)˖
˖h>'3,@21
(˖
˖h>'3,@21
*˖
˖h>'3,@2))
+˖
˖h>'3,@21
,˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(17)$;$//
$˖
˷̚˹
˖(;32685(/(9(/$//
$˖
2.
(;(&87(
Item/Display
Content
Setting
range
Default
value
A
AUTO
Auto
1 - 99
50
B
EXPOSURE1
Exposure 1
1 - 99
50
C
EXPOSURE2
Exposure 2
1 - 99
50
D
EXPOSURE3
Exposure 3
1 - 99
50
E
EXPOSURE4
Exposure 4
1 - 99
50
F
EXPOSURE5
Exposure 5
1 - 99
50
G
EXECUTE
MODE
MODE
AUTO
Print
mode
mode
Auto
1 - 6
1
1
(AUTO)
EXP1
Exposure 1
2
EXP2
Exposure 2
3
EXP3
Exposure 3
4
EXP4
Exposure 4
5
EXP5
Exposure 5
6
Item/Display
Content
Setting
range
Default
value
A
AUTO
Fine/Automatic
1 - 99
50
B
EXPOSURE1
Fine/Exposure 1
1 - 99
50
C
EXPOSURE2
Fine/Exposure 2
1 - 99
50
D
EXPOSURE3
Fine/Exposure 3
1 - 99
50
E
EXPOSURE4
Fine/Exposure 4
1 - 99
50
F
EXPOSURE5
Fine/Exposure 5
1 - 99
50
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(17)$;1250$/
$˖
˷̚˹
˖$872
$˖
˖(;32685(
%
˖(;32685(
&
˖(;32685(
'˖
˖(;32685(
)˖
˖(;32685(
(˖
˖(;(&87(02'($872
*˖
2.
(;(&87(
Click on the first or last page to see other MX-B381 / MX-B401 (serv.man7) service manuals if exist.