Sharp MX-B381 / MX-B401 (serv.man7) Service Manual ▷ View online
MX-B381/B401 SIMULATION 5 – 28
26-18
Purpose
Setting
Function (Purpose) Used to set Disable/Enable of the toner
save mode operation.
(For the Japan and the UK versions.)
(For the Japan and the UK versions.)
Section
Operation/Procedure
1)
1)
Select an item to be set with [
] [] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
The set value in step 2) is saved.
The set value in step 2) is saved.
26-30
Purpose
Setting
Function (Purpose) Used to set the operation mode corre-
sponding to the CE mark (Europe safety
standards). (For slow start to drive the fus-
ing heater lamp)
standards). (For slow start to drive the fus-
ing heater lamp)
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
* Even in Enable state, the control may not be executed due
The set value in step 1) is saved.
* Even in Enable state, the control may not be executed due
to the power frequency, etc.
26-32
Purpose
Setting
Function (Purpose) Used to set display or non-display of the
system setting menu.
Section
Operation/Procedure
1)
1)
Select an item to be set with [
] [] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
The set value in step 2) is saved.
Display or non-display of the following menu of the system set-
ting menu is set.
Set to ON for use of CRU, and set to OFF for use of SRU.
When it is set to ON, the following menu is displayed on the
system setting menu screen to allow the operation of the
menu.
The set value in step 2) is saved.
Display or non-display of the following menu of the system set-
ting menu is set.
Set to ON for use of CRU, and set to OFF for use of SRU.
When it is set to ON, the following menu is displayed on the
system setting menu screen to allow the operation of the
menu.
Item
Display
Content
Default
value
A
COPY
0
Copy toner save mode is inhibited.
0
1
Copy toner save mode is allowed
B
PRINTER
0
Printer toner save mode is
inhibited.
inhibited.
0
1
Printer toner save mode is
allowed.
allowed.
0
Control allowed
1
Control inhibited
U.S.A
1 (CE not supported)
EUROPE
0 (CE supported)
CANADA
1 (CE not supported)
U.K.
0 (CE supported)
INCH
1 (CE not supported)
AUS.
0 (CE supported)
JAPAN
1 (CE not supported)
AB_A
0 (CE supported)
AB_B
1 (CE not supported)
CHINA
0 (CE supported)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
721(56$9(02'(6(783
$˖
˷̚˹
˖&23<<(612
$˖
˖35,17(5<(612
%˖
2.
Item
Display
Content
Setting
range
Default
value
A
FAX ADJ
SET
SET
FAX setting screen (dial tone
detection, speed setting)
display (Select this setting
when the user himself
performs FAX dial tone
detection or speed setting.)
detection, speed setting)
display (Select this setting
when the user himself
performs FAX dial tone
detection or speed setting.)
0 (ON)
1 (OFF)
FAX setting screen (dial tone
detection, speed setting)
non-display
detection, speed setting)
non-display
1 (OFF)
B
CLEANING
PRINT SET
PRINT SET
Fusing cleaning print pattern
print screen display (Select
this setting when the user
himself prints the print pattern
for cleaning the fusing roller.
V characters are printed on all
the surface to remove foreign
material and residual toner
from the fusing roller.)
print screen display (Select
this setting when the user
himself prints the print pattern
for cleaning the fusing roller.
V characters are printed on all
the surface to remove foreign
material and residual toner
from the fusing roller.)
0 (ON)
1 (OFF)
Fusing cleaning print pattern
print screen non-display
print screen non-display
1 (OFF)
C
IMG SELF
PRINT SET
PRINT SET
Picture quality check self print
screen display (Select this
setting when the user himself
checks the engine print picture
quality. Two kinds of print
patterns of SIM64-4 are
printed.)
screen display (Select this
setting when the user himself
checks the engine print picture
quality. Two kinds of print
patterns of SIM64-4 are
printed.)
0 (ON)
1 (OFF)
Picture quality check self print
execution screen non-display
execution screen non-display
1 (OFF)
D
LIST
PRINT SET
PRINT SET
Machine data list (various
setting data) print screen
display
setting data) print screen
display
0 (ON)
1 (OFF)
Machine data list (various
setting data) print screen
non-display
setting data) print screen
non-display
1 (OFF)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
&(0$5.&21752/6(77,1*
$˖
˷̚˹
˖<(612
$˖
2.
MX-B381/B401 SIMULATION 5 – 29
When set to 0, it is displayed on the system setting screen. When
set to 1, it is not displayed on the system setting screen.
set to 1, it is not displayed on the system setting screen.
26-35
Purpose
Setting
Function (Purpose) Used to set the display mode of SIM 22-4
trouble history when a same trouble
occurred repeatedly. There are two display
modes: display as one trouble and display
as several series of troubles.
occurred repeatedly. There are two display
modes: display as one trouble and display
as several series of troubles.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
26-38
Purpose
Setting
Function (Purpose) Used to set Continue/Stop of print when the
maintenance life is reached.
Section
Operation/Procedure
1)
1)
Select an item to be set with [
] [] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
26-41
Purpose
Setting
Function (Purpose) Used to set Enable/Disable of the magnifi-
cation ratio automatic select function (AMS)
in the center binding mode.
in the center binding mode.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
E
UPDATE
SET
SET
Firmware update execution
screen display (Select this
setting when the user himself
updates the firmware. When
this menu is executed, the
guidance is displayed to guide
the user to execute update.)
screen display (Select this
setting when the user himself
updates the firmware. When
this menu is executed, the
guidance is displayed to guide
the user to execute update.)
0 (ON)
1 (OFF)
Firmware update execution
screen non-display
screen non-display
1 (OFF)
F
ERR MSG
SET
SET
Error message screen display
(When set to ON, "Call for
service" is displayed in case of
an error.)
(When set to ON, "Call for
service" is displayed in case of
an error.)
0 (ON)
1 (OFF)
Error message screen display
(When set to OFF, "Please
refer to operation manual" is
displayed in case of an error.)
(When set to OFF, "Please
refer to operation manual" is
displayed in case of an error.)
1 (OFF)
0
Only once display.
1
Any time display.
Item
Display
Content
Setting
range
Default
value
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
)81&7,216(77,1*)25&58
$˖
˷̚˹
˖)$;$'-6(712
$˖
˖&/($1,1*35,176(712
%˖
˖,0*6(/)35,176(712
&˖
˖/,6735,176(712
'˖
˖(5506*ǂ6(712
)˖
˖83'$7(6(712
(˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
7528%/(0(025<02'(6(783
$˖
˷̚˹
˖21&($1<
$˖
2.
Item
Display
Content
Default
value
A
MAINTENANCE
LIFE OVER
(0: CONTINUE
1: STOP)
LIFE OVER
(0: CONTINUE
1: STOP)
0
Print Enable/Disable setting
when the maintenance timing is
over (Print Continue)
when the maintenance timing is
over (Print Continue)
0
1
Print Enable/Disable setting
when the maintenance timing is
over (Print Stop)
when the maintenance timing is
over (Print Stop)
B
TC1 UNIT LIFE
OVER
(0: CONTINUE
1: STOP)
OVER
(0: CONTINUE
1: STOP)
0
Print Enable when the primary
transfer unit life is over.
(Print Continue)
transfer unit life is over.
(Print Continue)
0
1
Print Disable when the primary
transfer unit life is over.
(Print Stop)
transfer unit life is over.
(Print Stop)
C
TC2 UNIT LIFE
OVER
(0: CONTINUE
1: STOP)
OVER
(0: CONTINUE
1: STOP)
0
Print Enable when the
secondary transfer unit life is
over. (Print Continue)
secondary transfer unit life is
over. (Print Continue)
0
1
Print Disable when the
secondary transfer unit life is
over. (Print Stop)
secondary transfer unit life is
over. (Print Stop)
D
FUSER UNIT
LIFE OVER
(0: CONTINUE
1: STOP)
LIFE OVER
(0: CONTINUE
1: STOP)
0
Print Enable when the fusing
unit life is over. (Print Continue)
unit life is over. (Print Continue)
0
1
Print Disable when the fusing
unit life is over. (Print Stop)
unit life is over. (Print Stop)
E
DRUM UNIT
LIFE OVER
(0: CONTINUE
1: STOP)
LIFE OVER
(0: CONTINUE
1: STOP)
0
Print Enable when the drum
unit life is over. (Print Continue)
unit life is over. (Print Continue)
0
1
Print Disable when the drum
unit life is over. (Print Stop)
unit life is over. (Print Stop)
F
DEVE UNIT
LIFE OVER
(0: CONTINUE
1: STOP)
LIFE OVER
(0: CONTINUE
1: STOP)
0
Print Enable when the DV unit
life is over. (Print Continue)
life is over. (Print Continue)
0
1
Print Disable when the DV unit
life is over. (Print Stop)
life is over. (Print Stop)
0
AMS Disable
1
AMS Enable
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(/,)(29(56(77,1*
$˖
˷̚˹
˖0$,17(1$1&(/,)(29(5&217,18(6723
$˖
˖7&81,7/,)(29(5&217,18(6723
%˖
˖7&81,7/,)(29(5&217,18(6723
&˖
˖)86(581,7/,)(29(5&217,18(6723
'˖
˖'(9(81,7/,)(29(5&217,18(6723
)˖
˖'58081,7/,)(29(5&217,18(6723
(˖
2.
MX-B381/B401 SIMULATION 5 – 30
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
<Default value of each destination>
26-49
Purpose
Setting
Function (Purpose) Used to set the print speed of postcards
mode.
Section
Operation/Procedure
Select the copy speed mode. (Default: LOW)
Select the copy speed mode. (Default: LOW)
26-50
Purpose
Setting
Function (Purpose) Used to set functions.
Section
Section
Operation/Procedure
1)
1)
Select a target item of setting with [
] [] key.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
(*1) Default values
26-52
Purpose
Setting
Function (Purpose) Used to set whether non-printed paper
(insertion paper, cover paper) is counted up
or not.
or not.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
This setting is linked with SIM26-6. When the set value (destina-
tion) of SIM26-6 is changed, this setting is also changed accord-
ingly.
To set a desirable operation without linking with the destination, use
this simulation.
tion) of SIM26-6 is changed, this setting is also changed accord-
ingly.
To set a desirable operation without linking with the destination, use
this simulation.
U.S.A
0 (Disable)
EUROPE
1 (Enable)
CANADA
0 (Disable)
U.K.
1 (Enable)
INCH
0 (Disable)
AUS.
0 (Disable)
JAPAN
0 (Disable)
AB_A
0 (Disable)
AB_B
0 (Disable)
CHINA
0 (Disable)
Display/Item
Content
Default
value
POSTCARD
LOW
Low seed of postcard printing
LOW
HIGH
High speed of postcard printing
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
3$03+/(702'($066(77,1*
$˖
˷̚˹
˖<(612
$˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
&23<63(('02'(6(783
/2:
+,*+
3267&$5'
˖
Item/Display
Content
Default
value
A
BW REVERSE
0
BW reverse copy Disable
Refer
to *1
1
BW reverse copy Enable
B
FINISHER
FUNCTION
FUNCTION
0
Finisher special paper
The number of paper exit is
limited.
The number of paper exit is
limited.
0
1
Finisher special paper
The number of paper exit is not
limited.
The number of paper exit is not
limited.
C
FEED TRAY
COLOR
COLOR
0
Paper feed tray color display ON
during paper feed
during paper feed
0
1
Paper feed tray color display OFF
during paper feed
during paper feed
Destination
Item A
U S A
1
CANADA
1
INCH
1
JAPAN
1
AB_B
1
EUROPE
1
U K
0
AUS
1
AB_A
1
CHINA
1
0
Count up
1
No count up
Item/Display
Set value
Content
A
(0: YES 1: NO)
0
White sheet count-up setting
(Count)
(Count)
1
White sheet count-up setting
(Not Count)
(Not Count)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
)81&7,216(77,1*
$˖
˷̚˹
˖%:5(9(56(<(6
$˖
˖),1,6+(5)81&7,21<(6
%˖
˖)(('75$<&2/25<(6
&˖
2.
MX-B381/B401 SIMULATION 5 – 31
26-53
Purpose
Setting
Function (Purpose) User auto calibration (density and gradation
adjustment) Inhibit/Allow setting
(copy mode)
(copy mode)
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
26-54
Purpose
Setting
Function (Purpose) User auto calibration (density and gradation
adjustment) Inhibit/Allow setting
(printer mode)
(printer mode)
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
26-65
Purpose
Setting
Function (Purpose) Used to set the staple process restriction.
Section
Section
Operation/Procedure
Select a setting item and a setting condition.
Select a setting item and a setting condition.
[Target paper size]
8.5 x 14, 8.5 x 13.5, 8.5 x 13.4, 8.5 x 13
The staple capacity other than the above is fixed to 30 sheets.
8.5 x 14, 8.5 x 13.5, 8.5 x 13.4, 8.5 x 13
The staple capacity other than the above is fixed to 30 sheets.
26-69
Purpose
Setting
Function (Purpose) Used to set the operating conditions for
toner near end.
Section
Operation/Procedure
1)
1)
Select an item to be set with [
] [] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
Destination
Default
U.S.A
0 (Counted)
CANADA
0 (Counted)
INCH
0 (Counted)
JAPAN
1 (Not counted)
AB_B
0 (Counted)
EUROPE
0 (Counted)
U.K.
0 (Counted)
AUS.
1 (Not counted)
AB_A
0 (Counted)
CHINA
0 (Counted)
0
Inhibit (Default)
1
Allow
0
Inhibit (Default)
1
Allow
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$%/$1.3$3(5&281702'(6(783
$˖
˷̚˹
˖<(612
$˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1$%/,1*2)$8720$7,&*5$<&$/,%5$7,21
$˖
˷̚˹
˖<(612
$˖
2.
Item
Set
value
Content
Default
value
LIMIT COPIES
ON
Number of sets of stapling: Limited
ON
OFF
Number of sets of stapling:
Not Limited
Not Limited
LIMIT
SHEETS (L)
SHEETS (L)
15
Number of sheets of stapling:
Max. 15
Max. 15
30
30
Number of sheets of stapling:
Max. 30
Max. 30
Item/Display
Content
Default
value
A
TONER
PREPARATION
(0 : YES 1 : NO)
PREPARATION
(0 : YES 1 : NO)
0
The toner preparation
message is displayed.
message is displayed.
Refer to the
table, <List
of Default
values and
set values
for each
destination>
1
The toner preparation
message is not displayed.
message is not displayed.
B
TONER NEAR
END
(0: YES 1: NO)
END
(0: YES 1: NO)
0
The toner near end message
is displayed.
is displayed.
1
The toner near end message
is not displayed.
is not displayed.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1$%/,1*2)$8720$7,&*5$<&$/,%5$7,212)35,17(5
$˖
˷̚˹
˖<(612
$˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
),1,6+(5$/$5002'(6(78367$3/(/,0,7
21
2))
/,0,7&23,(6
˖
/,0,76+((76/
˖
21
Click on the first or last page to see other MX-B381 / MX-B401 (serv.man7) service manuals if exist.