Sharp MX-5500N / MX-6200N / MX-7000N (serv.man46) Service Manual ▷ View online
MX-7000N SIMULATION 7 – 13
3-10
Purpose
Adjustment
Function (Purpose) Used to adjust the finisher.
Section
Section
Finisher
Operation/Procedure
1)
1)
Select an item corresponding to the adjustment content with
[
[
↑] and [↓] keys on the touch panel.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key. (The set value is saved.)
<4K finisher>
<4K saddle finisher>
3-30
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the inserter and the
control circuits.
control circuits.
Section
Inserter
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
3-31
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the loads
in the inserter and the control circuit.
Section
Inserter
Operation/Procedure
1)
1)
Select a target of the operation check with the touch panel.
2)
Press [EXECUTE] key.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
Item
Display
Item
Set
range
Default
value
A
FRONT
ADJUST
ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
B
STAPLE
REAR
REAR
Staple binding position
adjustment (one position
at the rear)
adjustment (one position
at the rear)
94 - 106
100
C
STAPLE
FRONT
FRONT
Staple binding position
adjustment (one position
in front)
adjustment (one position
in front)
94 - 106
100
D
PUNCH
CENTER
CENTER
Punch center adjustment
30 - 70
50
E
PUNCH HOLE
Punch hole position
adjustment
adjustment
46 - 52
50
Item
Display
Item
Set
range
Default
value
A
SADDLE
POSITION
POSITION
Saddle binding position
adjustment
adjustment
197 - 203
200
B
FOLDING
POSITION
POSITION
Saddle folding position
adjustment
adjustment
192 - 208
200
C
FRONT
ADJUST
ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
D
STAPLE
REAR
REAR
Staple binding position
adjustment (one position
at the rear)
adjustment (one position
at the rear)
94 - 106
100
E
STAPLE
FRONT
FRONT
Staple binding position
adjustment (one position
in front)
adjustment (one position
in front)
94 - 106
100
F
PUNCH
CENTER
CENTER
Punch center adjustment
30 - 70
50
G
PUNCH HOLE
Punch hole position
adjustment
adjustment
46 - 52
50
SIMULATION NO.03-03
TEST
FIN LOAD CHECK
EXECUTE
1/1
CLOSE
FINRPS
FJPM
FJFM
FFM
FAM
FFJM
FRJM
FSM
FTLM1
FTLM2
FFSM
FSWM
FASM
FINRRS
FBRRS
FFDRRS
FBES
FSHC
FAORC
TH_SEN
Inserter sub tray pull-out detection
TS_SEN
Inserter sub tray storage detection
T_SEN
Inserter tray paper length detection
EMP_SEN
Inserter tray empty detection
REG_SEN
Inserter resist detection
TIM_SEN
Inserter timing detection
JCK_SEN
Inserter JAM cover open/close detection
H_SEN
Inserter reverse detection
HI_SEN
Inserter paper exit detection
HYK_SEN
Inserter reverse unit open/close detection
P_ST_SW
Inserter start SW
P_MO_SW
Inserter staple mode select SW
P_PN_SW
Inserter punch select SW
SET_SW
Inserter set SW
K_MOT
Inserter paper feed motor
Y_MOT
Inserter horizontal transport motor
H_MOT
Inserter reverse motor
F_SOL
Inserter flapper solenoid
A : 10
;
FRONT ADJUST
B : 100
;
STAPLE REAR
C : 100
;
STAPLE FRONT
D : 50
;
PUNCH CENTER
A:
SIMULATION NO.03-10
FINISHER ADJUSTMENT
10
0
20
OK
TEST
CLOSE
E : 50
;
PUNCH HOLE
FIN SENSOR CHECK
CLOSE
SIMULATION NO.03-30
TEST
1/1
TH_SEN
TS_SEN
T_SEN
EMP_SEN
REG_SEN
TIM_SEN
JCK_SEN
H_SEN
HI_SEN
HYK_SEN
P_ST_SW
P_MO_SW
P_PN_SW
SET_SW
MX-7000N SIMULATION 7 – 14
3-32
Purpose
Setting (Adjustment)
Function (Purpose) Used to set the adjustment value of the
inserter paper width detection level.
Section
Inserter
Operation/Procedure
1)
1)
Select an item corresponding to the adjustment content with
[
[
↑] and [↓] keys on the touch panel.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key. (The set value is saved.)
4
4-2
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the large capacity tray
(LCC) and the control circuit.
(LCC) and the control circuit.
Section
Large capacity tray (LCC)
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
<A4 LCC>
<A3 LCC>
4-3
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the loads
in the large capacity tray (LCC) and the
control circuit.
control circuit.
Section
Large capacity tray (LCC)
Operation/Procedure
1)
1)
Select a target of the operation check with the touch panel.
2)
Press [EXECUTE] key.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
<A4 LCC>
R_CL
Inserter resist clutch
P_LED
Inserter operation panel upper LED
Item
Display
Item
Set
range
A
MAX. POSITION
Inserter tray width detection
adjustment value (Max. width)
adjustment value (Max. width)
0 - 1023
B
POSITION 1
Inserter tray width detection
adjustment value (Adjustment
position 1)
adjustment value (Adjustment
position 1)
0 - 1023
C
POSITION 2
Inserter tray width detection
adjustment value (Adjustment
position 2)
adjustment value (Adjustment
position 2)
0 - 1023
D
MIN. POSOTION
Inserter tray width detection
adjustment value (Min. width)
adjustment value (Min. width)
0 - 1023
SIMULATION NO.03-31
TEST
INSERTER LOAD CHECK
1/1
CLOSE
K_MOT
Y_MOT
H_MOT
F_SOL
R_CL
P_LED
EXECUTE
A : 72
;
MAX. POSITION
B : 200
;
POSITION1
C : 10
;
POSITION2
D : 100
;
MIN. POSITION
A:
SIMULATION NO.03-32
INSERTER TRAY VALUE SETTING
72
0 1023
OK
TEST
CLOSE
LPFD
LCC transport sensor
LUD
LCC tray upper limit detection
LDD
LCC tray lower limit detection
LPED
LCC tray paper empty detection
LCD
LCC tray insertion detection
LDSW
LCC upper open/close detection SW
LRE
LCC lift motor encoder detection
L24VM
LCC 24V power monitor
LLSW
LCC upper limit SW
LTOD
LCC main unit connection detection
LPFD
LCC transport sensor
LUD
LCC tray upper limit detection
LDD
LCC tray lower limit detection
LPED
LCC tray paper empty detection
LCD
LCC tray insertion detection
LDSW
LCC upper open/close detection SW
LRE
LCC lift motor encoder detection
L24VM
LCC 24V power monitor
LLSW
LCC upper limit SW
LPUSW
LCC paper upper surface detection SW
LRRSW
LCC reverse winding detection SW
LTLSW
LCC tray lift SW
LTLD
LCC tray lock sensor
LIPSW
LCC illegal paper detection SW
LTOD
LCC main unit connection sensor
LPFM
LCC transport motor
LLM
LCC lift motor
LPFC
LCC paper feed clutch
LPFS
LCC paper feed solenoid
LTRC
LCC transport clutch
LCC SENSOR CHECK
CLOSE
SIMULATION NO.04-02
TEST
1/1
LPFD
LUD
LDD
LPED
LCD
LDSW
LRE
L24VM
LLSW
LTOD
MX-7000N SIMULATION 7 – 15
<A3 LCC>
4-5
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the clutch
(LTRC) in the LCC and the monitor.
Section
Large capacity tray (LCC)
Operation/Procedure
1)
1)
Press LTRC key to check the sync signal.
When normal: ON
When normal: ON
When abnormal: OFF
2)
Press the highlighted LTRC key to check the sync signal.
When normal: OFF
When normal: OFF
When abnormal: ON
5
5-1
Purpose
Operation test/Check
Function (Purpose) Used to check the operation of the display,
LCD in the operation panel, and control cir-
cuit.
cuit.
Section
Operation panel
Operation/Procedure
The LCD is changed as shown below.
The contrast changes every 2sec from the current level to Max.
The LCD is changed as shown below.
The contrast changes every 2sec from the current level to Max.
→
Min.
→ the current level. During this period, each LED is lighted.
5-2
Purpose
Operation test/Check
Function (Purpose) Used to check the operation of the heater
lamp and the control circuit.
Section
Fusing
Operation/Procedure
1)
1)
Select a target of the operation check with the touch panel.
2)
Press [EXECUTE] key.
The selected heater lamp performs ON/OFF operation.
When [EXECUTE] is pressed, the operation is stopped.
The selected heater lamp performs ON/OFF operation.
When [EXECUTE] is pressed, the operation is stopped.
LPFM
LCC transport motor
LLM
LCC lift motor
LPFC
LCC paper feed clutch
LPFS
LCC paper feed solenoid
LTRC
LCC transport clutch
LTLED
LCC tray LED lamp
LTLC
LCC tray lock clutch
LFAN
LCC separation auxiliary fan
SIMULATION NO.04-03
TEST
LCC LOAD CHECK
EXECUTE
1/1
CLOSE
LPFM
LLM
LPFC
LPFS
LTRC
SIMULATION NO.04-05
TEST
LCC SYNCRONIZING SIGNAL CHECK
LTRC
LTRC OFF
:
1/1
CLOSE
HL_UM
Heater lamp upper main
HL_US
Heater lamp upper sub
HL_LM
Heater lamp lower main
HL_EX
Heater lamp external EX1
Heater lamp external EX2
Heater lamp external EX2
HL_ALL
All heater lamps ON
SIMULATION NO.05-01
TEST
SIMULATION NO.05-01
TEST
After 6.0sec
1/1
SIMULATION NO.05-02
TEST
HEATER LAMP LOAD SETUP
CLOSE
HL_UM
HL_US
HL_LM
HL_EX
EXECUTE
HL_ALL
MX-7000N SIMULATION 7 – 16
5-3
Purpose
Operation test/Check
Function (Purpose) Used to check the operation of the copy
lamp and the control circuit.
Section
Optical (Image scanning)
Operation/Procedure
1)
1)
Select a target of the operation check with the touch panel.
2)
Press [EXECUTE] key.
The target lamp is lighted for 10 sec.
When [EXECUTE] is pressed, the operation is stopped.
The target lamp is lighted for 10 sec.
When [EXECUTE] is pressed, the operation is stopped.
5-4
Purpose
Operation test/Check
Function (Purpose) Used to check the operation of the dis-
charge lamp and the control circuit.
Section
Process
Operation/Procedure
1)
1)
Select a target of the operation check with the touch panel.
2)
Press [EXECUTE] key.
The target lamp is lighted for 30 sec.
When [EXECUTE] is pressed, the operation is stopped.
The target lamp is lighted for 30 sec.
When [EXECUTE] is pressed, the operation is stopped.
6
6-1
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the loads
(clutches and solenoids) in the paper trans-
port system and the control circuits.
port system and the control circuits.
Section
Paper transport/paper exit
Operation/Procedure
1)
1)
Select a target for the operation check with [
↑] and [↓] keys.
2)
Press [EXECUTE] key.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
OC COPY LAMP
OC copy lamp
DSPF COPY LAMP
DSPF copy lamp
DL_K
Discharge lamp K
DL_C
Discharge lamp C
Same control
DL_M
Discharge lamp M
DL_Y
Discharge lamp Y
SIMULATION NO.05-03
TEST
COPY LAMP CHECK
OC COPY LAMP
1/1
EXECUTE
CLOSE
DSPF COPY LAMP
SIMULATION NO.05-04
TEST
DISCHARGE LAMP CHECK
EXECUTE
1/1
CLOSE
DL_K
DL_C
DL_M
DL_Y
CPFM
Paper feed motor
LCCM
LCC transport motor
PFM
PS front motor
RRM
Resist motor
FPCM
Pressure change motor
FUM
Fusing motor
POMF
Paper exit motor normal rotation
POMR
Paper exit motor reverse rotation
WTM
Waste toner drive motor
TRC1
Vertical transport clutch upper
TRC2
Vertical transport clutch lower
TANCL
Tandem transport clutch
LPFC
LCC transport clutch
RRC
PS clutch
RRC2
PS clutch 2
PCSS
Process control shutter solenoid
MPUC
Manual paper feed clutch
MPFS
Manual paper feed take-up solenoid
MPGS
Manual paper feed gate solenoid
T1PUS
Tandem tray 1 pick-up solenoid
T2PUS
Tandem tray 2 pick-up solenoid
C3PUS
Cassette 3 pick-up solenoid
C4PUS
Cassette 4 pick-up solenoid
T1PFC
Tandem tray 1 paper feed clutch
T2PFC
Tandem tray 2 paper feed clutch
C3PFC
Cassette 3 paper feed clutch
C4PFC
Cassette 4 paper feed clutch
T1LUM
Tandem tray 1 lift-up motor
T2LUM
Tandem tray 2 lift-up motor
C3LUM
Cassette 3 lift-up motor
C4LUM
Cassette 4 lift-up motor
LSS_BK
LSU shutter solenoid BK
LSS_CL
LSU shutter solenoid CL
CLOSE
SIMULATION NO.06-01
TEST
FEED OUTPUT CHECK
EXECUTE
1/2
CPFM
LCCM
PFM
RRM
FPCM
FUM
POMF
POMR
WTM
TRC1
TRC2
TANCL
LPFC
RRC
RRC2
PCSS
MPUC
MPFS
MPGS
T1PUS
T2PUS
C3PUS
C4PUS
T1PFC
T2PFC
C3PFC
C4PFC
T1LUM
T2LUM
C3LUM
C4LUM
LSS_BK
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man46) service manuals if exist.