Sharp MX-5500N / MX-6200N / MX-7000N (serv.man46) Service Manual ▷ View online
MX-7000N SIMULATION 7 – 33
26-10
Purpose
Setting
Function (Purpose) Used to set the trial mode of the network
scanner.
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
26-18
Purpose
Setting
Function (Purpose) Used to set Disable/Enable of the toner
save mode operation. (For the Japan and
the UK versions.)
the UK versions.)
Section
Operation/Procedure
1)
1)
Select an item to be set with [
↑] and [↓] keys.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
26-30
Purpose
Setting
Function (Purpose) Used to set the operation mode corre-
sponding to the CE mark (Europe safety
standards). (For slow start to drive the fus-
ing heater lamp)
standards). (For slow start to drive the fus-
ing heater lamp)
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
0: Control allowed
0: Control allowed
1: Control inhibited
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
26-35
Purpose
Setting
Function (Purpose) Used to set the display mode of SIM 22-4
trouble history when a same trouble
occurred repeatedly. There are two display
modes: display as one trouble and display
as several series of troubles.
occurred repeatedly. There are two display
modes: display as one trouble and display
as several series of troubles.
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
0: Display as one trouble
1: Display as series of several troubles
0: Display as one trouble
1: Display as series of several troubles
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
TRIAL MODE
(0: YES 1: NO)
(0: YES 1: NO)
0: Trial mode setting
1: Trial mode cancel (Default)
1: Trial mode cancel (Default)
A
COPY
0: Copy toner save mode is inhibited. (Default)
1: Copy toner save mode is allowed
1: Copy toner save mode is allowed
B
PRINTER
0: Printer toner save mode is inhibited. (Default)
1: Printer toner save mode is allowed.
1: Printer toner save mode is allowed.
A:
A:
1
;
TRIAL MODE(0:YES 1:NO)
SIMULATION NO.26-10
NETWORK SCANNER TRIAL MODE SETUP
1
0
1
OK
TEST
CLOSE
A : 0
;
COPY (1:YES 0:NO)
B : 0
;
PRINTER (1:YES 0:NO)
A:
SIMULATION NO.26-18
TONER SAVE MODE SETUP
0
0
1
OK
TEST
CLOSE
U.S.A
1 (CE not supported)
EUROPE
0 (CE supported)
CANADA
1 (CE not supported)
U.K.
0 (CE supported)
INCH
1 (CE not supported)
AUS.
0 (CE supported)
JAPAN
1 (CE not supported)
AB_A
0 (CE supported)
AB_B
1 (CE not supported)
CHINA
0 (CE supported)
A : 1
;
(0:YES 1:NO)
A:
SIMULATION NO.26-30
CE MARK CONTROL SETTING
1
0
1
OK
TEST
CLOSE
A : 0
;
(0:ONCE 1:ANY)
A:
SIMULATION NO.26-35
TROUBLE MEMORY MODE SETUP
0
0
1
OK
TEST
CLOSE
MX-7000N SIMULATION 7 – 34
26-38
Purpose
Setting
Function (Purpose) Used to set whether printing is continued or
stopped when the developer life is expired
or when the fusing wed ends.
or when the fusing wed ends.
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
26-41
Purpose
Setting
Function (Purpose) Used to set Enable/Disable of the magnifi-
cation ratio automatic select function (AMS)
in the center binding mode.
in the center binding mode.
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
0: AMS Disable
0: AMS Disable
1: AMS Enable
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
26-49
Purpose
Setting
Function (Purpose) Used to set the copy speed mode of post-
cards.
Section
Operation/Procedure
Select the copy speed mode with the touch panel. (Default: LOW)
Select the copy speed mode with the touch panel. (Default: LOW)
26-50
Purpose
Setting
Function (Purpose) Used to set Enable/Disable of the black and
white highlight function and the 2-color/Sin-
gle display function.
gle display function.
Section
Operation/Procedure
1)
1)
Select an item to be set with [
↑] and [↓] keys on the touch
panel.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key. (The set value is saved.)
(*1) B COLOR MODE
OFF: Displayed
ON: Not displayed
A: MAINTENANCE LIFE OVER
0: Print continue
1: Print stop
1: Print stop
B: FUSER WEB END
0: Print continue
1: Print stop
1: Print stop
U.S.A
0 (Disable)
EUROPE
1 (Enable)
CANADA
0 (Disable)
U.K.
1 (Enable)
INCH
0 (Disable)
AUS.
0 (Disable)
JAPAN
0 (Disable)
AB_A
0 (Disable)
AB_B
0 (Disable)
CHINA
0 (Disable)
A : 0
; MAINTENANCE LIFE OVER(0:CONTINUE 1:STOP)
B : 1
; FUSER WEB END(0:CONTINUE 1:STOP)
A:
SIMULATION NO.26-38
ENGINE LIFE OVER SETTING
0
0
1
OK
TEST
CLOSE
A : 1
;
(1:YES 0:NO)
A:
SIMULATION NO.26-41
PAMPHLET MODE AMS SETTING.
1
0
1
OK
TEST
CLOSE
A
BW REVERSE
(0: NO 1: YES)
(0: NO 1: YES)
0:
Black and white reverse inhibited
1:
Black and white reverse allowed
B
COLOR MODE
(*1) 0 - 7
Refer to the table below.
Set value
Mode inhibit
2-color/Single
counter disable
Single
2-color
0
OFF
OFF
OFF
1
OFF
ON
OFF
2
ON
OFF
OFF
3
ON
ON
OFF
4
OFF
OFF
ON
5
OFF
ON
ON
6
ON
OFF
ON
7
ON
ON
ON
SIMULATION NO.26-49
TEST
COPY SPEED MODE SETUP
POSTCARD
:
LOW
HIGH
CLOSE
1/1
A : 1
; BW REVERSE : YES
B : 0
; COLOR MODE
A:
SIMULATION NO.26-50
FUNCTION SETTING
1
0
1
OK
TEST
CLOSE
MX-7000N SIMULATION 7 – 35
26-52
Purpose
Setting
Function (Purpose) Used to set whether non-print paper (inser-
tion paper, cover, etc.) is counted or not.
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
0: Counts up.
0: Counts up.
1: Does not count up.
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
26-53
Purpose
Setting
Function (Purpose) Used to set YES/NO of the auto color cali-
bration.
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
0: NO
0: NO
1: YES (Default)
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
26-54
Purpose
Setting
Function (Purpose) Used to set the printer calibration YES/NO.
Section
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
0: NO
0: NO
1: YES (Default)
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
26-65
Purpose
Setting
Function (Purpose) Used to set the finisher alarm mode.
Section
Section
Operation/Procedure
Select an item to be set with the touch panel.
Select an item to be set with the touch panel.
26-67
Purpose
Setting
Function (Purpose) Used to set the summer time timing and the
time zone.
Section
Operation/Procedure
1)
1)
Select a mode to be set with the touch panel.
[TIME ZONE] [SUMMER TIME]
[TIME ZONE] [SUMMER TIME]
2)
Select an item to be set with [
↑] and [↓] keys.
3)
Enter the adjustment value with 10-key.
4)
Press [OK] key.
The set value in step 3 is saved.
The set value in step 3 is saved.
A : 1
;
(0:YES 1:NO)
A:
SIMULATION NO.26-52
A BLANK PAPER COUNT MODE SETUP
1
0
1
OK
TEST
CLOSE
A : 1
;
(1:YES 0:NO)
A:
SIMULATION NO.26-53
ENAIBLING OF AUTOMATIC COLOR CALIBRATION
1
0
1
OK
TEST
CLOSE
LIMIT COPIES
ON
Staple limit copies ON (Default)
OFF
Staple limit copies OFF
A : 1
;
(1:YES 0:NO)
A:
SIMULATION NO.26-54
ENAIBLING OF AUTOMATIC COLOR CALIBRATION OF PRINTER
1
0
1
OK
TEST
CLOSE
SIMULATION NO.26-65
TEST
FINISHER ALARM MODE SETUP (STAPLE LIMIT)
CLOSE
1/1
LIMIT COPIES :
ON
OFF
MX-7000N SIMULATION 7 – 36
26-69
Purpose
Setting
Function (Purpose) Used to set the display of spare toner prep-
aration and near end when the toner quan-
tity reaches 25%.
tity reaches 25%.
Section
Operation/Procedure
1)
1)
Select an item to be set with [
↑] and [↓] keys.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
*1: Enable when the set item B is set to "0." The numbers of
printable quantity on the table above are estimated with A4
paper and the print rate of 5%.
The toner near end message is displayed. When the printing
quantity set in item D is reached, it is judged as "Toner end."
During this operation, insufficient density, thin spot, or improper
color balance may occur depending on the user's status of use.
To avoid this symptom, set the set item D to "1."
paper and the print rate of 5%.
The toner near end message is displayed. When the printing
quantity set in item D is reached, it is judged as "Toner end."
During this operation, insufficient density, thin spot, or improper
color balance may occur depending on the user's status of use.
To avoid this symptom, set the set item D to "1."
*2: The output quantity in items D and E are based on A4 paper
with print ratio of 5%.
TIME
ZONE
ZONE
A
GMT
±
0
+
1
–
B
GMT HOUR
0 - 13
GMT hour
C
GMT MINUTE
0 - 59
GMT minute
D
INTERNET
0
Internet clock YES
1
Internet clock NO
SUMMER
TIME
TIME
A
AUTO SUMMER
TIME ADJ
TIME ADJ
0
Automatic summer time
adjustment ON
adjustment ON
1
Automatic summer time
adjustment OFF
adjustment OFF
B
ADJ TIME HOUR
0 - 23
Adjustment time: Hour
C
ADJ TIME
MINUTE
MINUTE
0 - 59
Adjustment time: Minute
D
START TIME
MONTH
MONTH
1 - 12
Start time: Month
E
START TIME DAY
1 - 31
Start time: Day
F
START TIME
WEEK
WEEK
1 - 5
Start time: Week
G
START TIME A
DAY OF THE
WEEK
DAY OF THE
WEEK
1
MONDAY
2
TUESDAY
3
WEDNESDAY
4
THURSDAY
5
FRIDAY
6
SATURDAY
7
SUNDAY
H
START TIME
HOUR
HOUR
0 - 23
Start time: Hour
I
START TIME
MINUTE
MINUTE
0 - 59
Start time: Minute
J
START MODE
0
DAY
1
WEEK & A DAY OF THE
WEEK
WEEK
K
START UTC
0
YES
1
NO
L
END TIME
MONTH
MONTH
1 - 12
End time: Month
M
END TIME DAY
1 - 31
End time: Day
N
END TIME WEEK
1 - 5
End time: Week
O
END TIME A DAY
OF THE WEEK
OF THE WEEK
1
MONDAY
2
TUESDAY
3
WEDNESDAY
4
THURSDAY
5
FRIDAY
6
SATURDAY
7
SUNDAY
P
END TIME HOUR
0 - 23
End time: Hour
Q
END TIME
MINUTE
MINUTE
0 - 59
End time: Minute
R
END MODE
0
DAY
1
WEEK & A DAY OF THE
WEEK
WEEK
S
END UTC
0
YES
1
NO
A : 1
; AUTO SUMMER TIME ADJ : OFF
B : 9
; AUTO TIME HOUR
C : 0
; AUTO TIME MINUTE
D : 1
; START TIME MONTH : YES
A:
SIMULATION NO.26-67
SUMMER TIME&TIME ZONE ADJUSTMENT
1
0
1
OK
TEST
CLOSE
E : 1
; START TIME DAY
F : 1
; START TIME WEEK
G : 1
; START TIME A DAY OF THE WEEK : MONDAY
H : 1
; START TIME HOUR
I : 0
; START TIME MINUTE
J : 0
; START MODE : DAY
K : 0
; START UTC : YES
L : 0
; END TIME MONTH
EXECUTE
TIME ZONE
SUMMER TIME
A
TONER
PREPARATION
PREPARATION
0:
Toner ready message, icon display
(Default)
(Default)
1:
The toner preparation message is not
displayed.
displayed.
B
TONER NEAR
END
END
0:
Toner near end message display (Default)
1:
The toner near end message is not
displayed.
displayed.
C
TONER END
1:
Cartridge motor operation enabled at
NEAR END (Setting disable)
NEAR END (Setting disable)
2:
Cartridge motor operation disabled at
NEAR END (Setting disable)
NEAR END (Setting disable)
3:
Cartridge motor operation disabled at
NEAR END
NEAR END
D
TH COUNT (CL) *2
1:
Toner end detection in 0 sheet after toner
near end
near end
2:
Toner end detection in 25 sheets after
toner near end *1
toner near end *1
3:
Toner end detection in 50 sheet after toner
near end *1
near end *1
4:
Toner end detection in 100 sheets after
toner near end *1
toner near end *1
5:
Toner end detection in 200 sheets after
toner near end *1
toner near end *1
E
CONTINUOUS TH
COUNT (BK) *2
COUNT (BK) *2
1:
Cover open detection (recognition) in
120sec after toner cover open
120sec after toner cover open
2:
Cover open detection (recognition) in
210sec after toner cover open
210sec after toner cover open
3:
Cover open detection (recognition) in
300sec after toner cover open
300sec after toner cover open
4:
Cover open detection (recognition) in
390sec after toner cover open
390sec after toner cover open
5:
Cover open detection (recognition) in
480sec after toner cover open
480sec after toner cover open
A: 0
;
TONER PREPARATION(0:YES 1:NO)
B : 0
;
TONER NEAR END (0:YES 1:NO)
C : 3
;
NEAR END
A:
SIMULATION NO.26-69
TONER NEAR END SETTING
0
0
1
OK
TEST
CLOSE
D : 3
;
TH COUNTER(CL)
E : 3
;
CONTINUOUS TH COUNT(BK)
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man46) service manuals if exist.