Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man14) Service Manual ▷ View online
MX-4101N SIMULATION 6 – 9
[DSPF]
2-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and the detectors in the document
feed unit section and the control circuits.
feed unit section and the control circuits.
Section
RSPF/DSPF
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
[RSPF]
[DSPF]
NOTE: SWD_LEN and SWD_AD are not ON/OFF display.
2-3
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the loads
in the auto document feed unit and the con-
trol circuit.
trol circuit.
Section
RSPF/DSPF
Operation/Procedure
1)
1)
Select a target item of the operation check with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
[RSPF]
[DSPF]
Item/Display
Operation mode
Default value
(SINGLE)
300DPI
300DPI
(346.0mm/s)
(346.0mm/s)
300DPI
(346.0mm/s)
(346.0mm/s)
400DPI
400DPI
(259.5mm/s)
(259.5mm/s)
600DPI
600DPI
(173.0 mm/s)
(173.0 mm/s)
(DOUBLE)
300DPI
300DPI
(346.0mm/s)
(346.0mm/s)
300DPI
(346.0mm/s)
(346.0mm/s)
400DPI
400DPI
(259.5mm/s)
(259.5mm/s)
600DPI
600DPI
(173.0 mm/s)
(173.0 mm/s)
SSET
RSPF installation detection
SOCD
RSPF open/close detector
SCOV
RSPF cover open/close detector
SPED
RSPF document empty detector
SPPD1
RSPF document pass detector 1
(Paper enter detection)
(Paper enter detection)
SPPD2
RSPF document pass detector 2
(Resist roller front document transport detection)
(Resist roller front document transport detection)
SPPD3
RSPF document pass detector 3 (Document scanning front
document transport detection)
document transport detection)
SPPD4
RSPF document pass detector 4
(Reverse gate front document transport detection)
(Reverse gate front document transport detection)
SPPD5
RSPF document pass detector 5
(Document reverse rear document transport detection)
(Document reverse rear document transport detection)
SPLS1
RSPF document length detector 1 (Short)
SPLS2
RSPF document length detector 2 (Long)
STMPU
SPF stamp unit installation detector
SWD_LEN
RSPF guide plate position
SWD_AD
RSPF document width sensor (volume) output level
SSET
DSPF installation detection
SOCD
DSPF open/close detector
SCOV
DSPF cover open/close detector
SLCOV
DSPF lower door open/close detector
SPED1
DSPF document empty detector 1
SPED2
DSPF document empty detector 2
SPPD1
DSPF document pass detection 1 (Paper enter detection)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
63)$*,1*
300DPI
'3,
'3,
63)6&$1
˖
(;(&87(
'28%/(
SINGLE
SPPD2
DSPF document pass detector 2
(Resist roller front document transport detection)
(Resist roller front document transport detection)
SPPD3
DSPF document pass detector 3
(Document scanning front document transport detection)
(Document scanning front document transport detection)
SPPD4
DSPF document pass detector 4
(Reverse gate front document transport detection)
(Reverse gate front document transport detection)
SPPD5
DSPF document pass detector 5
(Document reverse rear document transport detection)
(Document reverse rear document transport detection)
SPOD
DSPF paper exit detector
SPRDMD
DSPF random feed paper size detection
SPLS1
DSPF document length detector 1 (Short)
SPLS2
DSPF document length detector (Long)
STLD
DSPF document tray lower limit detector
STUD
DSPF document tray upper limit detector
STMPU
DSPF stamp unit installation detector
SPFM
RSPF transport motor
SPRM_F
RSPF paper feed reverse motor (normal rotation)
SPRM_R
RSPF paper feed reverse motor (reverse rotation)
SPFC
RSPF paper feed clutch
SRRC
SPF resist roller clutch
SGS
RSPF document exit gate solenoid
STMPS
Finish stamp solenoid
SPUM
DSPF paper feed motor
SPFM
DSPF transport motor
SPOM
DSPF paper exit motor
SLUM
DSPF lift-up motor
SPFFAN
DSPF fan motor
SPFC
DSPF paper feed clutch
SRRC
DSPF resist roller clutch
SRRBC
DSPF resist roller break clutch
STRRC
DSPF No. 1 resist roller clutch
STRRBC
DSPF No. 1 resist roller break clutch
STRC
DSPF transport clutch
STMPS
Stamp solenoid
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
63)6(1625&+(&.ǂǂǂǂǂǂǂǂǂǂǂ6:'B/(1
6('B$'
66(7
62&'
6&29
63('
633'
633'
633'
633'
633'
63/6
63/6
67038
MX-4101N SIMULATION 6 – 10
3
3-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and the detectors in the finisher and
the control circuit.
the control circuit.
Section
Finisher
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
<Inner finisher>
<Saddle stitch finisher>
FED
Entry port paper detection (Status detection "1")
FBED
Tray paper detection
FULD
Tray upper limit detection
FMLLD
Tray intermediate lower limit detection
FLLD
Tray lower limit detection
FSLD1
Paper surface detection 1
FSLD2
Paper surface detection 2
FRLD
Roller up/down detection
FBRD
Belt separation detection
FFJHPD
Alignment HP detection front
FRJHPD
Alignment HP detection rear
FJPD
Alignment guide position detection
FSTPD
Staple tray paper detection
FSHPD
Staple drive HP detection
FSTHPD
Staple shift HP detection
FSD
Staple empty detection
FSTD
Staple lead edge position detection
FDSW
Door open detection
FFANLK
Fan motor lock detection
FPRPD
Punch rear position detection (Status detection "1")
FPUC
Punch unit connection detection
FPHPD
Punch HP detection
FPSHPD
Punch side resist HP detection
FPPD1
Punch paper surface detection 1
FPPD2
Punch paper surface detection 2
FPPD3
Punch paper surface detection 3
FPPD4
Punch paper surface detection 4
FPPD5
Punch paper surface detection 5
FPPD6
Punch paper surface detection 6
FPDD
Punch dust detection
FPPEND
Punch paper rear edge detection
FPDES1
Punch destination detection 1
FPDES2
Punch destination detection 2
㩷
㩷
㩷
㩷
㩷
㩷
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
63)287387&+(&.
6350B)
63
63)0
50B5
63)&
655&
6*6
67036
(;(&87(
PDPPD1
Paper pass paper transport detector 1
PDPPD2
Paper pass paper transport detector 2
PDCS
Paper pass cover Open/Close sensor
FPPD1
Paper delivery detector 1
FPAPHS_F
Paper alignment plate home position sensor F
FPAPHS_R
Paper alignment plate home position sensor R
FATPD
Paper alignment tray paper detector
FGHPS
Gripper home position sensor
FDTPD
Delivery tray paper detector
FPLD
Paper surface detector
FPPD2
Paper transport detector 2
FSPHS
Saddle plate home position sensor
FSTPD
Saddle exit tray paper detector
FSMRS
Saddle motor rotation sensor
FTULD
Tray upper limit detector
FTLLD
Tray lower limit detector
FTLMRS
Tray lift motor rotation sensor
FSHS
Staple home position sensor
FSSHPS
Stapler shift home position sensor
FSED
Staple empty detector
FSLS
Staple lead edge sensor
FTPS
Tray position sensor
FCD1
Cover detector 1
FCD2
Cover detector 2
FSSW1
Safety switch 1
FCD
Finisher connection detector
FSSSW1
Staple safety switch
FFL
Fan lock signal
FDRHS
Delivery roller home position sensor
FPPD3
Paper transport detector 3
FSATPD
Saddle paper alignment tray paper detector
FSSSW2
Stapler safety switch 2
FPHHD
Paper hold home position sensor
FSAPHS
Saddle alignment plate home position sensor
FSPGHS
Saddle paper guide home position sensor
FSRHS
Saddle roller home position sensor
FPDD
Delivery detector
FSSHS
Saddle staple home position sensor
FSSES
Saddle staple sensor
FSSCS
Saddle staple cover sensor
FSSSHS
Finisher saddle stapler shift home position sensor
FPMRS
Punch motor rotation sensor
FPD
Punch unit detection (connector)
FPCHPS
Punch home position sensor
FPDFS
Punch dust sensor
FPHPS
Punch unit home position sensor
FPTS
Punch timing sensor
FPES1
Punch paper edge sensor 1
FPES2
Punch paper edge sensor 2
FPES3
Punch paper edge sensor 3
FPES4
Punch paper edge sensor 4
FPPS
Punch paper position sensor
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
),16(1625&+(&.
3'33'
3'33'
3'&6
)33'
)3$3+6B)
)3$3+6B5
)$73'
)*+36
)'73'
)3/'
)33'
)63+6
)673'
)6056
)78/'
)7//'
)6/6
)736
)&'
)&'
)7/056
)6+6
)66+36
)6('
)66:
)&'
)666:
))/
)'5+6
)33'
)6$73'
)666:
)3++'
)6$3+6
)63*+6
)65+6
)3''
)66+6
)66(6
)66&6
)666+6
MX-4101N SIMULATION 6 – 11
3-3
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1)
1)
Select the item to be operation checked with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
<Inner finisher>
<Saddle stitch finisher>
3-10
Purpose
Adjustment
Function (Purpose) Used to adjust the finisher.
Section
Section
Finisher
Operation/Procedure
1)
1)
Select an adjustment target item with [
↑] [↓] key on the touch
panel.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
<Inner finisher>
<Saddle stitch finisher>
FINRPS
Entry port reverse pass solenoid
FSLS
Paper surface detection solenoid
FPDS
Paddle solenoid
FBRS
Belt separation solenoid
FRM
Registration motor
FSWM
Oscillation motor
FAM
Bundle exit paper exit motor
FFJM
Alignment motor front
FRJM
Alignment motor rear
FSM
Staple shift motor
FFSM
Staple motor
FTLM
Tray lift motor
FFANM
Fan motor
FPNM
Punch motor
FPSM
Punch side resist motor
PDPGS
Paper pass paper gate solenoid
PDPTM
Paper pass paper transport motor
PDCF
Paper pass cooling fan
FPTM1
Paper transport motor 1
FDRLM
Finisher paper exit roller lift motor
FGM
Gripper motor
FPAM-F
Paper alignment motor F
FPAM-R
Paper alignment motor R
FSSM
Stapler shift motor
FSM
Staple motor
FPTM2
Paper transport motor 2
FSDM
Saddle motor
FSPTM
Saddle paper transport motor
FSPAM
Saddle paper alignment motor
FSPM
Saddle positioning motor
FSDSM
Saddle staple motor
FPHS1
Paper holding solenoid 1
FPHS2
Paper holding solenoid 2
FTLM
Tray lift motor
FPM
Punch motor
FPSM
Punch shift motor
㩷
㩷
㩷
㩷
㩷
㩷
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
),1/2$'&+(&.
(;(&87(
3'3*6
3'370
)370
3'&)
)'5/0
)*0
)3$05
)3$0)
)660
)60
)370
)7/0
)6'0
)6370
)630
)63$0
)6'60
)3+6
)3+6
Item/Display
Content
Setting
range
Default
value
A
FRONT
ADJUST
ADJUST
Alignment position
adjustment (front)
adjustment (front)
2 - 18
10
B
REAR ADJUST
Alignment position
adjustment (rear)
adjustment (rear)
2 - 18
10
C
STAPLE REAR
Staple binding position
adjustment
(one position at the rear)
adjustment
(one position at the rear)
68 - 132
100
D
STAPLE
FRONT
FRONT
Staple binding position
adjustment
(one position in front)
adjustment
(one position in front)
68 - 132
100
E
STAPLE BOTH
Staple binding position
adjustment (center position
of two positions binding)
adjustment (center position
of two positions binding)
68 - 132
100
F
STAPLE PITCH
Staple binding position
adjustment (staple pitch of
two positions binding)
adjustment (staple pitch of
two positions binding)
68 - 132
100
G
PUNCH
CENTER
CENTER
Punch center positioning
sensor
sensor
37 - 63
50
H
PUNCH HOLE
Punch hole adjustment
(paper transport direction)
(paper transport direction)
42 - 58
50
Item/Display
Content
Setting
range
Default
value
A
SADDLE
POSITION
POSITION
Saddle stitch position
adjustment
adjustment
25 - 75
50
B
FOLDING
POSITION
POSITION
Saddle folding position
adjustment
adjustment
25 - 75
50
C
FRONT
ADJUST
ADJUST
Paper alignment position
adjustment (Front)
adjustment (Front)
35 - 65
50
D
REAR ADJUST
Paper alignment position
adjustment (Rear)
adjustment (Rear)
35 - 65
50
E
STAPLE REAR
Staple binding position
adjustment
(one position at the rear)
adjustment
(one position at the rear)
25 - 75
50
F
STAPLE REAR
R
R
Staple binding position
adjustment (one position at
the rear)
adjustment (one position at
the rear)
45 - 75
50
G
STAPLE
FRONT
FRONT
Staple binding position
adjustment
(one position in front)
adjustment
(one position in front)
25 - 75
50
H
STAPLE
FRONT R
FRONT R
Staple binding position
adjustment (one position in
front)
adjustment (one position in
front)
25 - 55
50
I
STAPLE BOTH
Staple binding position
adjustment (two positions
at the center)
adjustment (two positions
at the center)
45 - 55
50
J
STAPLE PITCH
Staple binding position
adjustment (two positions
in pitch)
adjustment (two positions
in pitch)
35 - 62
50
K
PUNCH
CENTER
CENTER
Punch center adjustment
35 - 65
50
L
PUNCH HOLE
Punch hole position
adjustment
adjustment
30 - 60
50
M
SADDLE_ADJU
ST_POS
ST_POS
Saddle alignment position
adjustment
adjustment
35 - 65
50
N
GRIPPER_POS
Gripper exit position
adjustment
adjustment
35 - 65
50
MX-4101N SIMULATION 6 – 12
NOTE: "A: SADDLE POSITION (Saddle binding position adjust-
ment)" and "B: FOLDING POSITION (Saddle folding posi-
tion adjustment"
The saddle binding position adjustment and the saddle
folding position adjustment can be executed in the system
setting menu. However, the adjustments in the system set-
ting are based on the adjustment value of this simulation.
If, therefore, the adjustment value of this simulation is set
to an extreme level, the adjustment range in the system
setting may be narrowed. (Adjustment range in the system
setting
tion adjustment"
The saddle binding position adjustment and the saddle
folding position adjustment can be executed in the system
setting menu. However, the adjustments in the system set-
ting are based on the adjustment value of this simulation.
If, therefore, the adjustment value of this simulation is set
to an extreme level, the adjustment range in the system
setting may be narrowed. (Adjustment range in the system
setting
±5.0mm)
In general, when the saddle binding position and the sad-
dle folding positions are adjusted to the center by this simu-
lation, the above trouble will not occur.
dle folding positions are adjusted to the center by this simu-
lation, the above trouble will not occur.
4
4-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the desk/large capac-
ity tray, and the control circuit of those.
ity tray, and the control circuit of those.
Section
Desk/Large capacity tray (LCC)
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
<Desk>
<A4 LCC>
4-3
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the loads
in the desk/large capacity tray (LCC), and
the control circuit of those.
the control circuit of those.
Section
Desk/Large capacity tray (LCC)
Operation/Procedure
1)
1)
Select the load item that is required to operation check with the
touch panel key.
touch panel key.
2)
Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
<Desk>
<A4 LCC>
DCSI1
Desk 1 installation detection
DPFD1
Desk 1 transport detection
DLUD1
Desk 1 upper limit detection
DPED1
Desk 1 paper empty detection
DCSPD1
Desk 1 remaining paper quantity detection
DCSS11
Desk 1 rear edge detection 1
DCSS12
Desk 1 rear edge detection 2
DCSS13
Desk 1 rear edge detection 3
DCSS14
Desk 1 rear edge detection 4
DCSI2
Desk 2 installation detection
DPFD2
Desk 2 transport detection
DLUD2
Desk 2 upper limit detection
DPED2
Desk 2 paper empty detection
DCSPD2
Desk 2 remaining paper quantity detection
DCSS21
Desk 2 rear edge detection 1
DCSS22
Desk 2 rear edge detection 2
DCSS23
Desk 2 rear edge detection 3
DCSS24
Desk 2 rear edge detection 4
DSW_DSK
Desk transport cover open/close detection
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
),1,6+(5$'-8670(17
$˖
˷̚˹
˖6$''/(326,7,21
$˖
˖)2/',1*326,7,21
%˖
˖)5217$'-867
&˖
˖5($5$'-867
'˖
˖67$3/(5($55
)˖
˖67$3/(5($5
(˖
˖67$3/()5217
*˖
˖67$3/()52175
+˖
˖67$3/(%27+
,˖
˖67$3/(3,7&+
-˖
˖381&+&(17(5
.˖
˖381&++2/(
/˖
2.
LPFD
LCC transport sensor
LUD
LCC tray upper limit sensor
LDD
LCC tray lower limit sensor
LPED
LCC tray paper empty sensor
LCD
LCC tray insertion detection
LDSW
LCC upper open/close detection SW
LRE
LCC lift motor encoder sensor
L24VM
LCC24V power monitor
LLSW
LCC upper limit SW
LTOD
LCC main unit connection detection
DPFM
Desk main motor
DLUM1
Desk 1 lift-up motor
DPUC1
Desk 1 paper feed clutch
DLUM2
Desk 2 lift-up motor
DPUC2
Desk 2 paper feed clutch
DTRC
Desk transport clutch
LPFM
LCC transport motor
LLM
LCC lift motor
LPFC
LCC paper feed clutch
LPFS
LCC paper feed solenoid
LTRC
LCC transport clutch
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'6./&&6(1625&+(&.
'&6,
'3)'
'/8'
'3('
'&63'
'&66
'&66
'&66
'&66
'&6,
'3)'
'/8'
'3('
'&63'
'&66
'&66
'&66
'&66
'6:B'6.
㩷
㩷
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'6./&&/2$'&+(&.
(;(&87(
'3)0
'/80
'/80
'38&
'38&
'75&
Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man14) service manuals if exist.