Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man14) Service Manual ▷ View online
MX-4101N SIMULATION 6 – 33
26-30
Purpose
Setting
Function (Purpose) Used to set the operation mode corre-
sponding to the CE mark (Europe safety
standards). (For slow start to drive the fus-
ing heater lamp)
standards). (For slow start to drive the fus-
ing heater lamp)
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
* Even in Enable state, the control may not be executed due
The set value in step 1) is saved.
* Even in Enable state, the control may not be executed due
to the power frequency, etc.
26-35
Purpose
Setting
Function (Purpose) Used to set the display mode of SIM 22-4
trouble history when a same trouble
occurred repeatedly. There are two display
modes: display as one trouble and display
as several series of troubles.
occurred repeatedly. There are two display
modes: display as one trouble and display
as several series of troubles.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
26-38
Purpose
Setting
Function (Purpose) Used to set Continue/Stop of print when the
maintenance life is reached.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
26-41
Purpose
Setting
Function (Purpose) Used to set Enable/Disable of the magnifi-
cation ratio automatic select function (AMS)
in the center binding mode.
in the center binding mode.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
<Default value of each destination>
0
Control allowed
1
Control inhibited
U.S.A
1 (CE not supported)
EUROPE
0 (CE supported)
CANADA
1 (CE not supported)
U.K.
0 (CE supported)
INCH
1 (CE not supported)
AUS.
0 (CE supported)
JAPAN
1 (CE not supported)
AB_A
0 (CE supported)
AB_B
1 (CE not supported)
CHINA
0 (CE supported)
0
Only once display.
1
Any time display.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
721(56$9(02'(6(783
$˖
˷̚˹
˖&23<<(612
$˖
˖35,17(5<(612
%˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
&(0$5.&21752/6(77,1*
$˖
˷̚˹
˖<(612
$˖
2.
Item/Display
Content
Default
value
A
MAINTENANCE
LIFE OVER
LIFE OVER
0
Print continue
0
1
Print stop
B
FUSER WEB END
(0: CONTINUE
1: STOP)
(0: CONTINUE
1: STOP)
0
Continue/Stop setting of print
when the fusing web is end
(Print Continue)
when the fusing web is end
(Print Continue)
0
1
Continue/Stop setting of print
when the fusing web is end
(Print Stop)
when the fusing web is end
(Print Stop)
0
AMS Disable
1
AMS Enable
U.S.A
0 (Disable)
EUROPE
1 (Enable)
CANADA
0 (Disable)
U.K.
1 (Enable)
INCH
0 (Disable)
AUS.
0 (Disable)
JAPAN
0 (Disable)
AB_A
0 (Disable)
AB_B
0 (Disable)
CHINA
0 (Disable)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
7528%/(0(025<02'(6(783
$˖
˷̚˹
˖21&($1<
$˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(/,)(29(56(77,1*
$˖
˷̚˹
˖0$,17(1$1&(/,)(29(5&217,18(6723
$˖
˖)86(5:(%(1'˖&217,18(˖6723
%˖
2.
MX-4101N SIMULATION 6 – 34
26-49
Purpose
Setting
Function (Purpose) Used to set the print speed of postcards
mode.
Section
Operation/Procedure
Select the copy speed mode with the touch panel. (Default: LOW)
Select the copy speed mode with the touch panel. (Default: LOW)
26-50
Purpose
Setting
Function (Purpose) Used to set functions.
Section
Section
Operation/Procedure
1)
1)
Select a target item of setting with [
↑] [↓] key on the touch
panel.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
(*1) Default values for each destination of item A/B/D
(*2) Item B: COLOR MODE set value (OFF: Displayed/ON: Not dis-
played)
played)
(*3)
Item/Display
Content
Default
value
A
BW REVERSE
0
BW reverse copy Disable
Refer
to *1
1
BW reverse copy Enable
B
COLOR MODE
2-color/Single color copy mode
Enable/Disable setting
Enable/Disable setting
Refer
to *1/*2
C
FINISHER
FUNCTION
FUNCTION
0
Finisher special paper
The number of paper exit is
limited.
The number of paper exit is
limited.
0
Refer
to *3
1
Finisher special paper
The number of paper exit is
not limited.
The number of paper exit is
not limited.
D
COLOR MODE
(PRINTER)
(PRINTER)
0
All colors and monochrome
counters are displayed.
counters are displayed.
Refer
to *1
1
All are displayed except for
the 3-color print counter.
the 3-color print counter.
2
Monochrome and full color
print counters are displayed.
print counters are displayed.
E
FEED TRAY
COLOR
COLOR
0
Paper feed tray color display
ON during paper feed
ON during paper feed
0
1
Paper feed tray color display
OFF during paper feed
OFF during paper feed
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
3$03+/(702'($066(77,1*
$˖
˷̚˹
˖<(612
$˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
&23<63(('02'(6(783
/2:
+,*+
3267&$5'
˖
Destination
Item A
Item B
Item D
U S A
1
0
2
CANADA
1
0
2
INCH
1
0
2
JAPAN
1
7
2
AB_B
1
0
2
EUROPE
1
0
2
U K
0
0
2
AUS
1
0
2
AB_A
1
0
2
CHINA
1
0
2
Set value
Mode
2-Color/Single
Single
2-color
Counter
0
OFF
OFF
OFF
1
OFF
ON
OFF
2
ON
OFF
OFF
3
ON
ON
OFF
4
OFF
OFF
ON
5
OFF
ON
ON
6
ON
OFF
ON
7
ON
ON
ON
Target
paper
Target paper setting
0
1
1K
saddle
stitch
finisher
saddle
stitch
finisher
Postcard,
envelope
envelope
The operation is stopped
when 30 sheets of a same
kind are discharged
continuously. When, however,
different kinds of sheets are
mixed and discharged and
less than 30 sheets of a kind
are continuously discharged,
the operation is performed
similarly to that of setting
value "1".
when 30 sheets of a same
kind are discharged
continuously. When, however,
different kinds of sheets are
mixed and discharged and
less than 30 sheets of a kind
are continuously discharged,
the operation is performed
similarly to that of setting
value "1".
The operation
is stopped
when the paper
exit tray is full
or when 500
sheets (94mm
thick) are
discharged.
is stopped
when the paper
exit tray is full
or when 500
sheets (94mm
thick) are
discharged.
Label
sheet, tab
sheet, OHP
sheet, tab
sheet, OHP
The operation is stopped
when 100 sheets of a same
kind are discharged
continuously. When, however,
different kinds of sheets are
mixed and discharged and
less than 100 sheets of a kind
are continuously discharged,
the operation is performed
similarly to that of setting
value "1".
when 100 sheets of a same
kind are discharged
continuously. When, however,
different kinds of sheets are
mixed and discharged and
less than 100 sheets of a kind
are continuously discharged,
the operation is performed
similarly to that of setting
value "1".
Inner
finisher
finisher
Postcard,
envelope
envelope
The operation is stopped
when 10 sheets of a same
kind are discharged
continuously. When, however,
different kinds of sheets are
mixed and discharged and
less than 10 sheets of a kind
are continuously discharged,
the operation is performed
similarly to that of setting
value "1".
when 10 sheets of a same
kind are discharged
continuously. When, however,
different kinds of sheets are
mixed and discharged and
less than 10 sheets of a kind
are continuously discharged,
the operation is performed
similarly to that of setting
value "1".
If it is set to "1,"
the operation is
stopped when
the paper exit
tray is full or
when 250
sheets
(35.5mm thick)
are discharged.
the operation is
stopped when
the paper exit
tray is full or
when 250
sheets
(35.5mm thick)
are discharged.
Label
sheet, tab
sheet, OHP
sheet, tab
sheet, OHP
The operation is stopped
when 100 sheets of a same
kind are discharged
continuously. When, however,
different kinds of sheets are
mixed and discharged and
less than 100 sheets of a kind
are continuously discharged,
the operation is performed
similarly to that of setting
value "1".
when 100 sheets of a same
kind are discharged
continuously. When, however,
different kinds of sheets are
mixed and discharged and
less than 100 sheets of a kind
are continuously discharged,
the operation is performed
similarly to that of setting
value "1".
MX-4101N SIMULATION 6 – 35
26-52
Purpose
Setting
Function (Purpose) Used to set whether non-printed paper
(insertion paper, cover paper) is counted up
or not.
or not.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
26-53
Purpose
Setting
Function (Purpose) User auto color calibration (color balance
adjustment) Inhibit/Allow setting
(copy mode)
(copy mode)
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
26-54
Purpose
Setting
Function (Purpose) User auto color calibration (color balance
adjustment) Inhibit/Allow setting
(printer mode)
(printer mode)
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
The set value in step 1) is saved.
26-65
Purpose
Setting
Function (Purpose) Used to set the finisher alarm mode.
Section
Section
Operation/Procedure
Use the touch key to set.
Use the touch key to set.
*1: 1-5 sheets (20 sets) / 6-10 sheets (15 sets)/
10-15 sheets (10 sets)
0
Count up
1
No count up
Destination
Default
U.S.A
0 (Counted)
CANADA
0 (Counted)
INCH
0 (Counted)
JAPAN
1 (Not counted)
AB_B
0 (Counted)
EUROPE
0 (Counted)
U.K.
0 (Counted)
AUS.
1 (Not counted)
AB_A
0 (Counted)
CHINA
0 (Counted)
0
Inhibit
1
Allow (Default)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
)81&7,216(77,1*
$˖
˷̚˹
˖%:5(9(56(<(6
$˖
˖&2/2502'(
%˖
˖),1,6+(5)81&7,21<(6
&˖
˖&2/2502'(35,17(5
'˖
˖)(('75$<&2/25<(6
(˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$%/$1.3$3(5&281702'(6(783
$˖
˷̚˹
˖<(612
$˖
2.
0
Inhibit
1
Allow (Default)
Item
Set
value
Content
Setting
range
Default
value
LIMIT
SHEETS
SHEETS
30
Number of sheets of
stapling: Max. 30
stapling: Max. 30
30 or 50
50
50
Number of sheets of
stapling: Max. 50
stapling: Max. 50
LIMIT
COPIES
COPIES
ON
Number of sets of stapling:
Max. 50 sets
Max. 50 sets
ON or
OFF
ON
OFF
Number of sets of stapling:
Not Limited
Not Limited
LIMIT
SHEETS(L)
SHEETS(L)
25
Number of sheets of
stapling: Max. 25
stapling: Max. 25
25 or 30
25
30
Number of sheets of
stapling: Max. 30
stapling: Max. 30
SADDLE
COPIES
COPIES
ON
Number of sets loaded in
the saddle staple: Limited
(*1)
the saddle staple: Limited
(*1)
ON or
OFF
ON
OFF
Number of sets loaded in
the saddle staple: Not
Limited
the saddle staple: Not
Limited
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1$%/,1*2)$8720$7,&&2/25&$/,%5$7,21
$˖
˷̚˹
˖<(612
$˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1$%/,1*2)$8720$7,&&2/25&2/,%5$7,212)35,17(5
$˖
˷̚˹
˖<(612
$˖
2.
MX-4101N SIMULATION 6 – 36
26-69
Purpose
Setting
Function (Purpose) Used to set the operating conditions for
toner near end.
Section
Operation/Procedure
1)
1)
Select an item to be set with [
↑] [↓] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
<List of Default values and set values for each destination>
(Contents of set items)
A: Enable/Disable setting of the toner preparation message display
when the toner remaining quantity reaches 25%.
B: Enable/Disable setting of the toner preparation message display
when the toner near end status is reached.
C: Enable/Disable setting of the machine operation when the toner
end status is reached.
For except Japan, performs operation of set value "3" regardless of
the setting value.
D: Setting of the allowable quantity of copy/print/FAX after display-
ing the message when item B is set to "0" (the message is dis-
played at toner near end). (Range: 0 - 200 sheets)
The number of output print allowed in item D is based on the
assumption that the sheets are of A4 size with print ratio of 5%.
(The number of outputs allowed differs depending on the paper
size and the print ratio.)
A: Enable/Disable setting of the toner preparation message display
when the toner remaining quantity reaches 25%.
B: Enable/Disable setting of the toner preparation message display
when the toner near end status is reached.
C: Enable/Disable setting of the machine operation when the toner
end status is reached.
For except Japan, performs operation of set value "3" regardless of
the setting value.
D: Setting of the allowable quantity of copy/print/FAX after display-
ing the message when item B is set to "0" (the message is dis-
played at toner near end). (Range: 0 - 200 sheets)
The number of output print allowed in item D is based on the
assumption that the sheets are of A4 size with print ratio of 5%.
(The number of outputs allowed differs depending on the paper
size and the print ratio.)
Set values of Item D and the number of output print allowed
1: Print Disable after toner near end
2: 25 sheets print Enable after toner near end
3: 50 sheets print Enable after toner near end
4: 100 sheets print Enable after toner near end
5: 200 sheets print Enable after toner near end
1: Print Disable after toner near end
2: 25 sheets print Enable after toner near end
3: 50 sheets print Enable after toner near end
4: 100 sheets print Enable after toner near end
5: 200 sheets print Enable after toner near end
NOTE: When item B is set to "0" and item D to a desired number,
printing can be made after toner near end. However, insuf-
ficient density, thin spots, or improper color balance may be
resulted depending on the using conditions. When item D
is set to "1" printing is disabled after toner near end. this
case, toner end display is made in the toner near end sta-
tus, and copy/print/FAX outputs are disabled.
ficient density, thin spots, or improper color balance may be
resulted depending on the using conditions. When item D
is set to "1" printing is disabled after toner near end. this
case, toner end display is made in the toner near end sta-
tus, and copy/print/FAX outputs are disabled.
26-73
Purpose
Setting
Function (Purpose) Enlargement continuous shoot, A3 wide
copy mode image loss (shade delete quan-
tity) adjustment
tity) adjustment
Section
Operation/Procedure
1)
1)
Select an item to be set with [
↑] [↓] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
When the adjustment value is increased, the image loss
(shade delete quantity) is increased.
When the adjustment value is increased, the image loss
(shade delete quantity) is increased.
Item/Display
Content
Setting
range
Default
value
A
TONER
PREPARATION
(0 : YES 1 : NO)
PREPARATION
(0 : YES 1 : NO)
0
The toner preparation
message is
displayed.
message is
displayed.
0 - 1
1
The toner preparation
message is not
displayed.
message is not
displayed.
B
TONER NEAR
END
(0 : YES 1 : NO)
END
(0 : YES 1 : NO)
0
The toner near end
message is
displayed.
message is
displayed.
0 - 1
1
The toner near end
message is not
displayed.
message is not
displayed.
C
TONER END
1
Operation Enable in
TONER END
TONER END
1 - 3
2
2
Operation STOP in
TONER END
TONER END
3
Operation STOP in
TONER END
TONER END
D
TONER END
COUNT
COUNT
Setting of the number of
copy/print/FAX outputs
Enable after TONER
NEAR END.
copy/print/FAX outputs
Enable after TONER
NEAR END.
1 - 5
1
E
TONER E-MAIL
ALART
ALART
0
Condition for Low
status send of E-mail
alert
status send of E-mail
alert
0 - 1
1
When the toner
preparation message
is displayed (in near
near toner end)
preparation message
is displayed (in near
near toner end)
1
Condition for Low
status send of E-mail
alert
When near toner end
status send of E-mail
alert
When near toner end
Destination
Set value
Toner preparation
message
Toner near end message
U.S.A
0 (Displayed)
0 (Displayed)
CANADA
0 (Displayed)
0 (Displayed)
INCH
0 (Displayed)
0 (Displayed)
JAPAN
0 (Displayed)
1 (Not Displayed)
AB_B
0 (Displayed)
0 (Displayed)
EUROPE
0 (Displayed)
0 (Displayed)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
),1,6+(5$/$5002'(6(78367$3/(/,0,7
/,0,76+((76
˖
21
2))
/,0,7&23,(6
˖
/,0,76+((76˄/
˖
21
2))
6$''/(&23,(6
˖
U.K.
0 (Displayed)
0 (Displayed)
AUS.
0 (Displayed)
0 (Displayed)
AB_A
0 (Displayed)
0 (Displayed)
CHINA
0 (Displayed)
0 (Displayed)
Destination
Set value
Toner preparation
message
Toner near end message
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
721(51($5(1'6(77,1*
$˖
˷̚˹
˖721(535(3$5$7,21<(612
$˖
˖721(51($5(1'<(612
%˖
˖721(5(1'
&˖
˖721(5(1'&2817
'˖
˖721(5(0$,/$/$57
(˖
2.
Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man14) service manuals if exist.