Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man14) Service Manual ▷ View online
MX-4101N SIMULATION 6 – 5
41
1
Used to check the operations of the document size sensor and the control circuit.
2
Used to adjust the document size sensor detection level.
3
Used to check the operations of the document size sensor and the control circuit.
43
1
Used to set the fusing temperature in each mode.
4
Used to set the fusing temperature 2 in each mode. (Continued from SIM 43-1.)
20
Used to set the environmental correction under low temperature and low humidity (L/L) for the fusing
temperature setting (SIM 43-1) in each paper mode.
temperature setting (SIM 43-1) in each paper mode.
21
Used to set the environment correction under high temperature and high humidity (H/H) for the fusing
temperature setting (SIM 43-1) in each paper mode.
temperature setting (SIM 43-1) in each paper mode.
22
Used to set the environment correction under low temperature and low humidity (L/L) for the fusing
temperature setting (SIM 43-4) in each paper mode.
temperature setting (SIM 43-4) in each paper mode.
23
Used to set the environment correction under high temperature and high humidity (H/H) for the fusing
temperature setting (SIM 43-4) in each paper mode.
temperature setting (SIM 43-4) in each paper mode.
24
Used to set the correction of the temperature adjustment value of SIM 43-1 and 43-4.
31
Used to check the operation of the fusing web cleaning motor.
Fusing
32
Used to set various items related to the forcible operation of web cleaning when job end.
Fusing
44
1
Used to set each correction operation function in the image forming (process) section.
Image process (Photoconductor/
Developing/Transfer/Cleaning)
Developing/Transfer/Cleaning)
2
Used to adjust the sensitivity of the image density sensor (registration sensor).
Process
4
Used to set the conditions of the high density process control operation.
Process
6
Used to execute the high density process control forcibly.
Process
9
Used to display the result data of the high density process control operation.
Image process (Photoconductor/
Developing/Transfer/Cleaning)
Developing/Transfer/Cleaning)
12
Used to display the operation data of the high density process control and the image density sensor
(registration sensor).
(registration sensor).
Image process
(Photoconductor/Developing)
(Photoconductor/Developing)
13
Used to perform the color image sensor (image registration sensor F) calibration.
14
Used to display the output level of the temperature and humidity sensor.
Process (OPC drum, development)/
Fusing/LSU
Fusing/LSU
16
Used to display the toner density control data.
Developing system
21
Used to set the half tone process control target.
Process
22
Used to display the toner patch density level in the half tone process control operation.
Process
24
Used to display the correction target and the correction level in the half tone process control operation.
Process
25
Used to set the calculating conditions of the correction value for the half tone process control.
Process
26
Used to execute the half tone process control compulsorily.
Process
27
Used to clear the correction data of the half tone process control.
Process
28
Used to set the process control execution conditions.
Process
29
Used to set the operating conditions of the process control during a job.
Process
31
Used to adjust the OPC drum phase. (Manual adjustment)
Process
37
Used to set the development bias correction level in the continuous printing operation.
43
Used to display the identification information of the developing unit.
Developing system
61
Used to adjust the color image density sensor. (The adjustment is made according to the input of SIM44-
13 to set the target value of the color sensor gain adjustment.)
13 to set the target value of the color sensor gain adjustment.)
46
1
Used to adjust the copy density in the copy mode.
2
Used to adjust the copy density in the copy mode.
4
Used to adjust the density in the image send mode.
5
Used to adjust the density in the image send mode.
8
Used to adjust the image send mode color balance RGB.
9
Used to adjust the scan image density.
10
Used to adjust the copy color balance and the gamma (for each color copy mode).
16
Used to adjust the monochrome copy density and the gamma (for each monochrome copy mode).
19
Used to set the operating conditions for the density scanning (exposure) of monochrome auto copy mode
documents.
documents.
21
Copy color balance adjustment (Manual adjustment)
23
Used to set the density correction of copy high density section (High density tone gap supported).
24
Copy color balance adjustment (Auto adjustment)
25
Used to adjust the copy color balance. (Single color copy mode)
26
Used to reset the single color mode color balance set value to the default.
27
Used to adjust the gamma/density of copy images, texts, and line image edges.
30
Used to adjust the resolution in the sub scanning direction in the copy mode.
32
Used to adjust the document background density reproducibility in the monochrome auto copy mode.
36
Used to adjust the colors in the 2-color copy mode.
37
Used to adjust the color document reproducibility in the monochrome copy mode.
38
Used to adjust the black component amount in the color copy mode.
39
Used to adjust the sharpness of FAX send images.
40
Used to adjust the FAX send image density. (Collective adjustment of all the modes)
Main
Sub
Functions
Section
MX-4101N SIMULATION 6 – 6
46
41
Used to adjust the FAX send image density. (Normal)
42
Used to adjust the FAX send image density. (Fine)
43
Used to adjust the FAX send image density. (Super Fine)
44
Used to adjust the FAX send image density. (Ultra fine)
45
Used to adjust the FAX send image density. (600dpi).
47
Used to set the compression rate of copy and scan images (JPEG).
51
Used to adjust the gamma for the copy mode heavy paper mode and the image process mode.
52
Used to set the gamma default for the copy mode heavy paper and the image process mode.
(The set values of SIM46-51 are set to the default values.)
(The set values of SIM46-51 are set to the default values.)
54
Used to perform the engine half tone automatic density adjustment (dither).
60
Used to adjust the sharpness in the color auto copy mode.
61
Used to adjust the area separation recognition level.
62
Used to set the operating conditions of the ACS, the area separation, the background image process, and
the auto exposure mode.
the auto exposure mode.
63
Used to adjust the density in the copy low density section.
74
Copy color balance adjustment (Auto adjustment)/
Printer color balance adjustment (Auto adjustment)
Printer color balance adjustment (Auto adjustment)
90
Used to adjust the high compression PDF ASIC.
48
1
Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning
direction).
direction).
5
Used to correction the scan image magnification ratio (in the sub scanning direction).
Scanner section
6
Used to adjust the rotation speed of each motor.
49
1
Used to perform the firmware update.
3
Used to update the operation manual in the HDD.
5
Used to perform the watermark update.
50
1
Copy image position, image loss adjustment
2
Used to adjust the copy image position and the image loss. (This simulation is a simplified version of SIM
50-1).
50-1).
5
Used to adjust the print lead edge image position. (PRINTER MODE)
6
Used to adjust the copy image position and the image loss. (RSPF/DSPF mode)
RSPF/DSPF
7
Used to adjust the copy image position and the image loss (RSPF/DSPF mode).
(This simulation is a simplified version of SIM 50-6.)
(This simulation is a simplified version of SIM 50-6.)
RSPF/DSPF
10
Used to adjust the black print image magnification ratio and the off-center position.
(The adjustment is made separately for each paper feed section.)
(The adjustment is made separately for each paper feed section.)
12
Used to perform the scan image off-center position adjustment.
(The adjustment is made separately for each scan mode.)
(The adjustment is made separately for each scan mode.)
20
Image registration adjustment (Main scanning direction) (Manual adjustment)
21
Image registration adjustment (Sub scanning direction) (Manual adjustment)
22
Used to adjust the image registration. (Main scan direction, sub scan direction)
(Auto adjustment)/OPC drum phase adjustment (Auto adjustment)
(Auto adjustment)/OPC drum phase adjustment (Auto adjustment)
24
Used to display the detail data of SIM 44-2, 50-20, 21 and 22.
27
Used to perform the image loss adjustment of scanned images in the FAX or image send mode.
28
Used to automatically adjust the image loss, void area, image off-center, and image magnification ratio.
51
1
Used to adjust the ON/OFF timing of the secondary transport voltage.
2
Used to adjust the contact pressure (deflection amount) on paper by the main unit and the RSPF/DSPF
resist roller. (This adjustment is performed when there is a considerable variation in the print image
position on the paper or when paper jams frequently occur.)
resist roller. (This adjustment is performed when there is a considerable variation in the print image
position on the paper or when paper jams frequently occur.)
53
6
Used to adjust the detection level of the RSPF/DSPF document width.
7
Used to adjust the RSPF/DSPF document size width sensor.
8
Used to adjust the document lead edge reference and the RSPF/DSPF mode document scan position.
55
1
Used to set the specifications of the engine control operations. (SOFT SW)
2
Used to set the specifications of the scanner control operation. (SOFT SW)
3
Used to set the specifications of the controller operation. (SOFT SW)
56
1
Used to transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.)
2
Used to backup the data in the EEPROM. SRAM, and HDD (including user authentication data and
address data) to the USB memory. (Corresponding to the device cloning and the storage backup.)
address data) to the USB memory. (Corresponding to the device cloning and the storage backup.)
3
Used to backup the document filing data to the USB memory.
4
Used to backup the JOB log data to the USB memory.
60
1
Used to check the operations (read/write) of the MFP PWB image memory (SDRAM).
2
Used to set the MFP PWB onboard SDRAM.
61
1
Used to check the LSU polygon motor rotation and laser detection.
LSU
3
Used to set the laser power
4
Used to print the print image skew adjustment pattern. (LSU unit)
Main
Sub
Functions
Section
MX-4101N SIMULATION 6 – 7
62
1
Used to execute the hard disk format (except operation manual area).
2
Used to check read/write of the hard disk (partial).
3
Used to check read/write of the hard disk (all areas).
6
Used to perform the self diagnostics of the hard disk.
7
Used to print the hard disk self diagnostics error log.
8
Used to format the hard disk. (Excluding the system area and the operation manual area)
10
Used to delete the job log data.
11
Used to delete the document filing data.
12
Used to set Enable/Disable of auto format in a hard disk trouble.
13
Used to format the hard disk. (only the operation manual area)
63
1
Used to display the shading correction result.
Scanner
2
Used to perform shading.
3
Used to perform scanner (CCD) color balance and gamma auto adjustment.
Scanner
4
Used to display the SIT chart patch density.
5
Used to perform the scanner (CCD) color balance and gamma default setting.
6
Used to display the scan level and the density level of the copy color balance adjustment patch.
63
7
Used to register the service target of the copy mode auto color balance adjustment.
8
Used to set the default of the service target of the copy mode auto color balance adjustment.
11
Used to set the target color balance of the copy mode auto color balance adjustment.
64
1
Test print. (Self print) (Color mode)
2
Test print. (Self print) (Monochrome mode)
4
Printer test print. (Self print) (256 gradations)
5
Printer test print. (Self print) (PCL)
6
Printer test print. (Self print) (PS)
7
Used to print the adjustment pattern of the test print .(Self print).
(The adjustment pattern of SIM46-21 is printed.)
(The adjustment pattern of SIM46-21 is printed.)
65
1
Used to adjust the touch panel (LCD display section) detection coordinates.
Operation panel section
2
Used to display the touch panel (LCD display section) detection coordinates.
5
Used to check the operation panel key input.
67
17
Printer reset
Printer
24
Printer color balance adjustment (Auto adjustment)
Printer
25
Printer color balance adjustment (Manual adjustment)
Printer
26
Used to set the target color balance of the printer mode auto color balance adjustment.
Printer
27
Used to set the service target of the printer mode auto color balance adjustment.
Printer
28
Used to set the default of the service target of the printer mode auto color balance adjustment.
Printer
31
Used to clear the printer calibration value.
Printer
33
Used to change the gamma of the printer screen. (for PCL/PS)
Printer
34
Used to set the density correction in the printer high density section. (Support for the high density section
tone gap)
tone gap)
Printer
36
Used to adjust the density in the low density section.
Printer
52
Used to set the default of the gamma of the printer screen. (for PCL/PS)
Printer
54
Printer color balance adjustment (Automatic adjustment for each dither)
Printer
70
MFP PWB SRAM data clear
MFP PWB
Main
Sub
Functions
Section
MX-4101N SIMULATION 6 – 8
3. Details of simulation
1
1-1
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the scanner
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1)
1)
Select the operation speed with the touch panel key.
2)
Press [EXECUTE] key.
Scanning is once performed at the speed corresponding to the
scan resolution (operation speed).
Scanning is once performed at the speed corresponding to the
scan resolution (operation speed).
1-2
Purpose
Operation test/check
Function (Purpose) Used to check the sensors in the scanner
(reading) section and the related circuits.
Section
Scanner (reading)
Operation/Procedure
The operating status of the sensor is displayed.
When "MHPS" is highlighted, the scanner unit is in the home posi-
tion.
The operating status of the sensor is displayed.
When "MHPS" is highlighted, the scanner unit is in the home posi-
tion.
1-5
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the scanner
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1)
1)
Select the operation speed with the touch panel key.
2)
Press [EXECUTE] key.
Scanning is repeated at the speed corresponding to the scan
resolution (operation speed).
When [EXECUTE] key is pressed, the operation is terminated.
Scanning is repeated at the speed corresponding to the scan
resolution (operation speed).
When [EXECUTE] key is pressed, the operation is terminated.
2
2-1
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the auto
document feed unit and the control circuit.
Section
RSPF/DSPF
Operation/Procedure
1)
1)
Select the operation mode and the speed with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The RSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).
When [EXECUTE] key is pressed, the operation is terminated.
The RSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).
When [EXECUTE] key is pressed, the operation is terminated.
[RSPF]
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI
(346.0mm/s)
(346.0mm/s)
300DPI
(346.0mm/s)
(346.0mm/s)
400DPI
400DPI
(259.5mm/s)
(259.5mm/s)
600DPI
600DPI
(173.0mm/s)
(173.0mm/s)
1200DPI
1200DPI
(86.5mm/s)
(86.5mm/s)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(5&+(&.
300DPI
'3,
'3,
2&6&$1
˖
'3,
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(56(1625&+(&.
MHPS
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI
(346.0mm/s)
(346.0mm/s)
300DPI
(346.0mm/s)
(346.0mm/s)
400DPI
400DPI
(259.5mm/s)
(259.5mm/s)
600DPI
600DPI
(173.0mm/s)
(173.0mm/s)
1200DPI
1200DPI
(86.5mm/s)
(86.5mm/s)
Item/Display
Operation mode
Default value
(SINGLE)
300DPI
300DPI
(259.5mm/s)
(259.5mm/s)
300DPI
(259.5mm/s)
(259.5mm/s)
400DPI
400DPI
(259.5mm/s)
(259.5mm/s)
600DPI
600DPI
(173.0 mm/s)
(173.0 mm/s)
(DOUBLE)
300DPI
300DPI
(259.5mm/s)
(259.5mm/s)
300DPI
(259.5mm/s)
(259.5mm/s)
400DPI
400DPI
(259.5mm/s)
(259.5mm/s)
600DPI
600DPI
(173.0 mm/s)
(173.0 mm/s)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(5&+(&.
300DPI
'3,
'3,
2&6&$1
˖
'3,
(;(&87(
Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man14) service manuals if exist.