Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) Service Manual ▷ View online
MX-4070V MX-PN15B/C/D (PUNCH MODULE) 12 – 10
44) Install the inner cover of the finisher with the screw.
45) Install the knobs (x2).
46) For MX-FN29 (Saddle finisher), also install the knob shown in the
figure below.
47) After installing the finisher to the main unit, fix the position shown
in the figure below with the screw. (Use the screw removed at
Step 11.)
Step 11.)
48) Close the front door of the finisher.
49) Fix the harness section of the interface unit, and connect the har-
ness.
MX-4070V MX-PN15B/C/D (PUNCH MODULE) 12 – 11
50) Fix the connector cover with the screw.
B. Turn ON the power of the main unit
1)
Connect the power plug of the machine to the power outlet, and
turn ON the main power switch and the operation panel power
switch.
turn ON the main power switch and the operation panel power
switch.
MX-4070V MX-FN30 (FINISHER) 13 – 1
MX-4070V
Service Manual
[13] MX-FN30 (FINISHER)
1. Unpacking
A. Packed items check
B. Removal of the finisher
NOTE: It is recommendable to work by two or more persons.
1)
Open the box, and take out the accessary boxes, packed items,
and cushioning materials.
and cushioning materials.
2)
While holding the upper parts of the main unit and lifting the one
side of the machine, remove the cushioning materials. At this
time, be sure to hold up the plastic bag of the lifting side.
side of the machine, remove the cushioning materials. At this
time, be sure to hold up the plastic bag of the lifting side.
3)
While holding the upper parts of the main unit and lifting the oppo-
site side of Step.2), remove the cushioning materials and the plas-
tic bag.
site side of Step.2), remove the cushioning materials and the plas-
tic bag.
4)
Remove the slope plates (x2) and the fixing pins (x2). Fixing pins
are attached to the slope plate with the tape.
are attached to the slope plate with the tape.
5)
Align the line on the pallet and the arrow mark on the slope plate,
and mount the slope plates (x2) to the pallet with the screws (x2).
and mount the slope plates (x2) to the pallet with the screws (x2).
6)
Put the casters of the main unit on the slope plates, and then
slowly move the main unit to the floor.
slowly move the main unit to the floor.
No.
Name
Quantity
1
Connection guide plate
1
2
Interface pass guide
1
3
Earth plate
1
4
Stapler unit staple case
1
5
Screw (M4× 14 S- tight)
4
6
Screw (M3× 6 S- tight)
5
7
Staple position label (for scanner)
1
8
Staple position label (for RSPF)
1
1
2
3
4
5
6
7
8
MX-4070V MX-FN30 (FINISHER) 13 – 2
C. Removal of the fixing tape and protection
material
1)
Remove all fixing tapes/protection materials from the exterior.
2)
Open the front upper cover. Remove all tapes and take out the
protection materials from the stapler section.
protection materials from the stapler section.
3)
Close the front upper cover.
Ĭ
ĭ
Į
į
İ
ı
ı
IJ
ij
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) service manuals if exist.