Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) Service Manual ▷ View online
MX-4070V MX-PN16B/C/D (PUNCH MODULE) 15 – 1
MX-4070V
Service Manual
[15] MX-PN16B/C/D (PUNCH MODULE)
1. Unpacking
A. Packed items check
B. Packed items check
1)
Open the outer box and remove the punch unit and packed items.
2)
Remove all the cushioning materials and tapes from the punch
unit.
unit.
3)
Remove 3 screws to remove 2pcs of attaching material.
NOTE: Save the 3 screws removed for installation of the punch unit.
2. Installation
NOTE: Be sure to install the punch unit before installing the finisher to
the main unit. In case of installing the punch unit afterward,
remove the finisher from the main unit once.
remove the finisher from the main unit once.
NOTE: Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the
power outlet.
power outlet.
Make sure that the data lamp on the operation panel does not
light up or blink prior to the installation.
light up or blink prior to the installation.
A. Removal of rear cabinet and top cover
1)
Remove filament tapes from the packing materials.
2)
When the finisher is connected to the main unit, disconnect the
interface cable and remove the finisher.
interface cable and remove the finisher.
3)
Remove two screws fastened to rear cabinet of the finisher.
4)
Incline upper part of the rear cabinet and remove the rear cabinet
while lifting the pawls of the rear cabinet.
while lifting the pawls of the rear cabinet.
No.
Name
Quantity
1
Punch unit
1
2
Punch waste full sensor unit
1
3
Harness
1
4
Punch waste Tray
1
5
Positioning guide
1
6
Punch position label (for RSPF/DSPF)
1
7
Punch position label (for scanner)
1
8
Punch cushion A (Resin board)
1
9
Punch cushion B (PORON- Sponge)
1
10
Screw (S tight screw, M3x8)
1
1
2
3
4
5
6
7
8
9
10
Remove two screws.
Position of the pawls of the rear cabinet
and insertion slot on the finisher unit
and insertion slot on the finisher unit
Rear cabinet
Finisher unit
MX-4070V MX-PN16B/C/D (PUNCH MODULE) 15 – 2
5)
Open front cabinet of the finisher.
6)
Remove 4 screws to remove a fulcrum for top cover.
7)
Incline a lever to the right and open top cover.
8)
Slide the top cover toward the direction of an arrow 1 and remove
the top cover toward the direction of an arrow 2.
the top cover toward the direction of an arrow 2.
B. Removal of dummy unit
1)
Disconnect the connector on rear side.
2)
Remove a screw, slide toward front and uplift the guide. The hook
will be removed; remove the guide from rear side.
will be removed; remove the guide from rear side.
3)
Cut 5 sections of insertion slot for punch waste tray using a nipper
and remove.
and remove.
C. Attachment of positioning guide (Packed item
No. 5)
1)
Attach right edge of positioning guide in reference to the center of
the scale. Use a screw (M3x6) removed in the step 3) in “Unpack-
ing”.
the scale. Use a screw (M3x6) removed in the step 3) in “Unpack-
ing”.
Top cover
Fulcrum
Screws
ĭ
Į
Ĭ
MX-4070V MX-PN16B/C/D (PUNCH MODULE) 15 – 3
D. Installation of punch unit (Packed item No. 1)
1)
Attach Punch cushion B (Packed item No. 9) along the
reference face on Punch inner cover for Punch unit.
reference face on Punch inner cover for Punch unit.
2)
Install the punch unit from rear side of the finisher by letting it
through under the top cover.
through under the top cover.
3)
Make sure there is no space between base of the punch unit and
a frame.
a frame.
4)
Fix the punch unit with a screw. Use a screw (M3x6) removed in
the step 3) in “Unpacking”.
the step 3) in “Unpacking”.
5)
Attach the fulcrum for top cover again using 4 screws.
E. Attachment of punch waste full sensor unit
(Packed item No. 2)
1)
Remove filament tapes from the packing materials.
6FDOH
Reference face
Reference face
Punch inner cover
Top cover
Fulcrum
Screws
MX-4070V MX-PN16B/C/D (PUNCH MODULE) 15 – 4
2)
Connect the connector on punch waste full sensor unit to the
punch unit.
punch unit.
F. Wiring and connecting a cable
(Packed item No. 3)
1)
Wire the cable as shown in the photo below.
G. Attachment of Punch cushion A (Packed item
No. 8)
1)
Attach the Punch cushion A to the inner cover along the reference
face.
face.
H. Installation of punch waste tray
(Packed item No. 4)
1)
Install the punch waste tray as shown in the photo below.
I.
Attachment of top cover and rear cabinet
1)
Attach the top cover by moving toward the direction of an arrow 1.
Then slide the top cover in the direction of an arrow 2.
Then slide the top cover in the direction of an arrow 2.
6HQVRUKROGHU
3XQFKZDVWHIXOOVHQVRUXQLW
+DUQHVVJXLGH
&DEOH
Reference face:
Touch inner cover with left side surface of Punch cushion A.
Touch Punch inner cover with back side of Punch cushion A.
Inner cover
Punch inner cover
Attach the cushion A.
Attach the cushion A.
3XQFKZDVWHWUD\
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) service manuals if exist.