Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man6) Service Manual ▷ View online
MX-4070V SIMULATION 6 – 10
SWD_LEN and SWD_AD are not ON/OFF display.
2-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the loads
in the automatic document feeder and the
control circuit.
in the automatic document feeder and the
control circuit.
Section
SPF
Operation/Procedure
1) Select a target item of the operation check with the touch panel
1) Select a target item of the operation check with the touch panel
key.
2) Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
When [EXECUTE] key is pressed, the operation is terminated.
DSPF
RSPF
3
3-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the sen-
sors and the detectors in the finisher and
the control circuit.
sors and the detectors in the finisher and
the control circuit.
Section
Finisher
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
Inner finisher
Inner finisher punch unit
Staple-free Staple Unit
1K finisher
1K saddle finisher
STMPU
SPF stamp UN installation detection
SWD_LEN
SPF document guide plate position (Unit: 0.1mm)
SWD_AD
SPF document detection volume output AD value
Display
Content
SLUM
Lift up motor
SPFC
Document feed clutch
SPFFAN
Cooling fan motor
SPOM
Document exit motor
SRRC
Registration roller clutch
STRC
Transport roller 2 clutch
STRRC
Transport roller 1 clutch
Display
Content
SPUM_F
SPF paper feed motor (normal rotation)
SPUM_R
SPF paper feed motor (reverse rotation)
SPFM_F
SPF transport motor (normal rotation)
SPFM_R
SPF transport motor (reverse rotation)
SPRS
Paper exit roller pressure control solenoid (SPF)
SRRC
Registration roller clutch (SPF)
STMPS
Stamp solenoid
No,/Display item
Content
FNECODTC
Staple-less staple connection detection signal
FNINTSNS
Punch unit paper rear edge detection signal
FNMANSW
Manual staple switch
FNMSW1
Front cover switch
FNPS1
Discharged paper sensor
FNPS2
Paddle home position sensor
Display
Content
FNPS3
Knurling home position sensor
FNPS4
Alignment plate front home position sensor
FNPS5
Alignment plate rear home position sensor
FNPS6
Staple tray paper sensor
FNPS7
Paper exit assist home position sensor
FNPS8
Bundle hold home position sensor
FNPS9
Paper height sensor
FNPS10
Paper exit tray lower limit sensor
FNPS11
Staple shift home position sensor
FNPS12
Manual staple paper detection sensor
FNPS14
Paper exit tray position sensor
FNPS16
Slide position sensor
FNPUDTC
Punch unit connection detection signal
FNSTPLHP
Staple home position sensor
FNSTPLLS
Staple empty detection
FNSTPLRE
Staple lead edge sensor
No,/Display item
Content
FCFULL_S
Punch dust full sensor
FCPI_S
Punch home position sensor
FCPUENCS
Punch motor rotation sensor
FCRI_S
Punch mode sensor
FCYKPTRS
Punch unit paper rear edge sensor
No,/Display item
Content
FNPS13
Staple-free staple unit position sensor
FNPS15
Staple-free staple unit home position sensor
No,/Display item
Content
BLTHPS
Release position sensor
ENT
Inlet sensor
EXGPLTHP
Paper exit guide plate open/close home position
sensor
sensor
FDRSW
Door open/close sensor
HITHP
Flapper home position sensor
JOGHPS
Jogger home position sensor
LDWNLMUT
Lift tray lower limit lower sensor
LMDLT
Intermediate feeder left sensor
PRFEX
Proof paper exit sensor
PRFTRYFL
Proof tray full sensor
RMDLT
Intermediate feeder right sensor
SFTROLHP
Shift home position sensor
STMHP
Staple shift home position detection
STPDRRHP
Staple driver home position sensor
STPNEND
Staple near end sensor
STPSPRM
Staple self-priming sensor
STPTRPAP
Staple tray paper empty sensor
UDWNLMUT
Lift tray lower limit upper sensor
UPCVR
Upper cover open/close sensor
UPEX
Shift paper exit (Lift tray paper exit) sensor
UPLMUTSW
Lift tray upper switch
UTNRH
Tray near home detection sensor
UTRPH
Lift tray paper surface sensor
No,/Display item
Content
BDLTRS
Bundle transport sensor
BLTHPS
Release home position sensor
ENDSHP
Rear edge stopper home position sensor
ENDSTRS
Rear edge stopper transport sensor
ENT
Inlet sensor
EXGPLTHP
Paper exit guide plate open/close home position
sensor
sensor
FDRSW
Door open/close sensor
FLDCMHP
Folding cam home position sensor
FLDEX
Half folding paper exit sensor
FLDPLTHP
Folding blade home position sensor
No,/Display item
Content
MX-4070V SIMULATION 6 – 11
1K finisher punch unit
3K finisher
3K saddle finisher
HITHP
Flapper home position sensor
JOGHPS
Jogger home position sensor
LDWNLMUT
Lift tray lower limit lower sensor
LMDLT
Intermediate feeder left sensor
LPRSRLHP
Bundle transport lower pressure release home
position sensor
position sensor
PRFEX
Proof paper exit sensor
PRFTRYFL
Proof tray full sensor
RMDLT
Intermediate feeder right sensor
SDLFLLL
Half folding tray full lower sensor
SDLFLLU
Half folding tray full upper sensor
SFTROLHP
Shift home position sensor
SSSTPCHP
Saddle stitch staple clincher home position sensor
STMHP
Staple shift home position detection
STPDRRHP
Staple driver home position sensor
STPNEND
Staple near end sensor
STPSPRM
Staple self-priming sensor
STPTRPAP
Staple tray paper empty sensor
STTKSH
Staple retracting sensor
UDWNLMUT
Lift tray lower limit upper sensor
UPCVR
Upper cover open/close sensor
UPEX
Shift paper exit (Lift tray paper exit) sensor
UPLMUTSW
Lift tray upper limit switch
UPRSRLHP
Bundle transport upper pressure release home
position sensor
position sensor
UTNRH
Tray near home detection sensor
UTRPH
Lift tray paper surface sensor
No,/Display item
Content
PAPPOS
Horizontal registration detection sensor
PAPPOSHP
Horizontal registration detection shift home position
sensor
sensor
PNCHENC
Punch rear position sensor
PNCHHP
Punch home position sensor
PNCHHPFL
Punch hopper full sensor
PNCHMVHP
Punch shift home position sensor
PSLTDSW1
Punch selection DIP SW1
PSLTDSW2
Punch selection DIP SW2
No,/Display item
Content
FN1DDS
DIP SW1 detection sensor
FN1DO
Paper exit paper surface detection sensor 1
FN1DPS
Push SW1 detection sensor
FN2DDS
DIP SW2 detection sensor
FN2DO
Paper exit paper surface detection sensor 2
FN2DPS
Push SW2 detection sensor
FN3DDS
DIP SW3 detection sensor
FN4DDS
DIP SW4 detection sensor
FNAMS
Manual staple operation SW
FNB
Buffer sensor
FNDCP
Punch connection detection signal
FNDCS
Saddle connection detection signal
FNDES
Staple empty detection sensor
FNDFET
Escape tray full detection sensor
FNDOCFD
Front door open/close detection sensor
FNDOGPN
Alignment unit paddle lift paper surface detection
sensor
sensor
FNDOHS
Staple cuing detection sensor
FNDPMS
Manual staple paper detection sensor
FNDPOPT
Process tray paper surface sensor
FNE
Entry port sensor
FNEE
Escape paper exit sensor
FNFMTLC
Load tray full (Large coated paper full) sensor
FNFMTLS
Load tray middle (Large coated paper full) sensor
FNFMTSS
Load tray lower limit (Small coated paper full)
sensor
sensor
FNHPAR
Rear edge assist home position sensor
FNHPCSLS
Staple-free stapling clinch home position sensor
FNHPDSS
Staple drive home position sensor
No,/Display item
Content
FNHPFECE
Escape/saddle transport switch flapper home
position sensor
position sensor
FNHPFR
Rear edge falling home position sensor
FNHPGJFN
Alignment unit front alignment plate lift home
position sensor
position sensor
FNHPGJRN
Alignment unit rear alignment plate lift home
position sensor
position sensor
FNHPGKS
Take-up knurling lift home position sensor
FNHPGPN
Alignment unit paddle lift home position sensor
FNHPJF
Front edge alignment plate home position sensor
FNHPJFN
Alignment unit front alignment plate home position
sensor
sensor
FNHPJR
Rear edge alignment plate home position sensor
FNHPJRN
Alignment unit rear alignment plate home position
sensor
sensor
FNHPMSS
Staple shift home position sensor
FNHPMT
Load tray home position sensor
FNHPP
Paddle home position sensor
FNHPRPN
Alignment unit paddle rotation home position
sensor
sensor
FNHPS
Oscillation home position sensor
FNHPTF
Front edge tongue home position sensor
FNHPTR
Rear edge tongue home position sensor
FNMCSLS
Staple-free stapling motor clock sensor
FNOCFD
Front door open/close switch
FNSSS
Staple safety switch
FNTBP
Preprocessing timing sensor
FNULMT
Load tray upper limit sensor
No,/Display item
Content
FN1DDS
DIP SW1 detection sensor
FN1DO
Paper exit paper surface detection sensor 1
FN1DPS
Push SW1 detection sensor
FN2DDS
DIP SW2 detection sensor
FN2DO
Paper exit paper surface detection sensor 2
FN2DPS
Push SW2 detection sensor
FN3DDS
DIP SW3 detection sensor
FN4DDS
DIP SW4 detection sensor
FNAMS
Manual staple operation SW
FNB
Buffer sensor
FNDCP
Punch connection detection signal
FNDCS
Saddle connection detection signal
FNDES
Staple empty detection sensor
FNDFET
Escape tray full detection sensor
FNDOCFD
Front door open/close detection sensor
FNDOGPN
Alignment unit paddle lift paper surface detection
sensor
sensor
FNDOHS
Staple cuing detection sensor
FNDPMS
Manual staple paper detection sensor
FNDPOPT
Process tray paper surface sensor
FNE
Entry port sensor
FNEE
Escape paper exit sensor
FNFMTLC
Load tray full (Large coated paper full) sensor
FNFMTLS
Load tray middle (Large coated paper full) sensor
FNFMTSS
Load tray lower limit (Small coated paper full)
sensor
sensor
FNHPAR
Rear edge assist home position sensor
FNHPCSLS
Staple-free stapling clinch home position sensor
FNHPDSS
Staple drive home position sensor
FNHPFECE
Escape/saddle transport switch flapper home
position sensor
position sensor
FNHPFR
Rear edge falling home position sensor
FNHPGJFN
Alignment unit front alignment plate lift home
position sensor
position sensor
FNHPGJRN
Alignment unit rear alignment plate lift home
position sensor
position sensor
FNHPGKS
Take-up knurling lift home position sensor
FNHPGPN
Alignment unit paddle lift home position sensor
FNHPJF
Front edge alignment plate home position sensor
FNHPJFN
Alignment unit front alignment plate home position
sensor
sensor
No,/Display item
Content
MX-4070V SIMULATION 6 – 12
3K finisher punch unit
Paper pass unit
3-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the load in
the finisher and the control circuit.
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1) Select the item to be operation checked with the touch panel
1) Select the item to be operation checked with the touch panel
key.
2) Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
When [EXECUTE] key is pressed, the operation is terminated.
Inner finisher
1K finisher
1K Saddle finisher
1K Finisher punch unit
3K Finisher
FNHPJR
Rear edge alignment plate home position sensor
FNHPJRN
Alignment unit rear alignment plate home position
sensor
sensor
FNHPMSS
Staple shift home position sensor
FNHPMT
Load tray home position sensor
FNHPP
Paddle home position sensor
FNHPRPN
Alignment unit paddle rotation home position
sensor
sensor
FNHPS
Oscillation home position sensor
FNHPTF
Front edge tongue home position sensor
FNHPTR
Rear edge tongue home position sensor
FNMCSLS
Staple-free stapling motor clock sensor
FNOCFD
Front door open/close switch
FNSSS
Staple safety switch
FNTBP
Preprocessing timing sensor
FNULMT
Load tray upper limit sensor
FSDU
Saddle unit detection sensor
FSE
Saddle unit entry port sensor
FSEB
Saddle unit folding bundle paper exit sensor
FSEPB
Saddle unit folding bundle loading paper empty
sensor
sensor
FSESFS
Saddle unit staple front staple empty sensor
FSESRS
Saddle unit staple rear staple empty sensor
FSHPDSS
Saddle unit staple drive home position sensor
FSHPEL
Saddle unit switch lever home position sensor
FSHPG
Saddle unit gripper home position sensor
FSHPJ
Saddle unit alignment plate home position sensor
FSHPP
Saddle unit paddle home position sensor
FSHPSR
Saddle unit rear edge stopper home position
sensor
sensor
FSHPT
Saddle unit pushing home position sensor
FSMCE
Saddle unit paper exit motor clock sensor
FSMCF
Saddle unit folding motor clock sensor
FSPV
Saddle unit vertical path sensor
No,/Display item
Content
FC1DR
Punch horizontal registration detection sensor 1
FC2DR
Punch horizontal registration detection sensor 2
FC3DR
Punch horizontal registration detection sensor 3
FC4DR
Punch horizontal registration detection sensor 4
FC5DR
Punch horizontal registration detection sensor 5
FCDFWP
Punch dust full detection sensor
FCEP
Punch hole encoder sensor
FCHPP
Punch hole home position sensor
FCHPR
Punch horizontal registration home position sensor
No,/Display item
Content
PDOS1
Relay cover open/close detection 1
PDOS2
Relay cover open/close detection 2
PDPPD1
Relay transport detection 1
PDPPD2
Relay transport detection 2
No,/Display item
Content
No,/Display item
Content
FNM1
Transport motor
FNM10
Paddle motor
FNM2
Roller motor
FNM3
Front alignment motor
FNM4
Rear alignment motor
FNM5
Assist motor
FNM6
Tray shift motor
FNM7
Staple shift motor
FNM9
eco staple motor
FNSL
Rear edge falling motor
FNSTPLIF
Staple motor
No,/Display item
Content
BLT_M
Release motor
ENTRS_M
Entry port transport motor
EXGPLT_M
Paper exit guide plate open/close motor
EXTRS_M
Paper exit transport/Flapping, drawing roller motor
JCTG_S
Branch solenoid
JOG_M
Jogger motor
PSN_M
Flapping motor
SFT_M
Shift motor
STPMOV_M
Staple motor
STPMV_M
Staple shift motor
TRYLFT_M
Tray lift motor
UPTRS_M
Proof transport motor
No,/Display item
Content
BLT_M
Release motor
ENDS_M
Rear edge stopper motor
ENTRS_M
Entry port transport motor
EXGPLT_M
Paper exit guide plate open/close motor
EXTRS_M
Paper exit transport/Flapping, drawing roller motor
FLDPLT_M
Folding blade motor
FLTRS_M
Folding transport motor
GDLED
Guide LED
JCTG_S
Branch solenoid
JOG_M
Jogger motor
LPRSRL_M
Bundle transport lower pressure release motor
PSN_M
Flapping motor
SFT_M
Shift motor
STPMOV_M
Staple motor
STPMV_M
Staple shift motor
TRYLFT_M
Tray lift motor
UBTRS_M
Bundle transport upper motor
UPRSRL_M
Bundle transport upper pressure release/
Reference fence evacuation motor
Reference fence evacuation motor
UPTRS_M
Proof transport motor
No,/Display item
Content
PNCH_M
Punch motor
PNCHMV_M
Punch shift motor
STSMOV_M
Punch horizontal registration detection shift motor
No,/Display item
Content
FNCDP
Paddle drive clutch
FNCDRUS
Oscillation lower roller drive clutch
FNCEDCE
Escape transport drive switch clutch
FNMAR
Rear edge assist motor
FNMB
Buffer motor
FNMDJFN
Alignment unit front alignment plate drive motor
FNMDJRN
Alignment unit rear alignment plate drive motor
FNMDT
Tongue drive motor
FNME
Discharge motor
FNMEC
Entry port transport motor
FNMFECES
Escape/Saddle transport switch flapper motor
MX-4070V SIMULATION 6 – 13
3K Saddle finisher
3K finisher punch unit
Paper pass unit
3-10
Purpose
Adjustment
Function (Purpose)
Used to adjust the finisher.
Section
Finisher
Operation/Procedure
1) Select an adjustment target item with scroll key on the touch
1) Select an adjustment target item with scroll key on the touch
panel.
2) Enter the set value with 10-key.
3) Press [OK] key. (The set value is saved.)
3) Press [OK] key. (The set value is saved.)
Inner finisher
1K Finisher/1K Saddle finisher
FNMFR
Rear edge falling motor
FNMGJFN
Alignment unit front alignment plate lift motor
FNMGJRN
Alignment unit rear alignment plate lift motor
FNMGMT
Load paper tray lift motor
FNMGPN
Alignment unit paddle lift motor
FNMGRS
Take-up switch roller lift motor
FNMJF
Front alignment motor
FNMJR
Rear alignment motor
FNMMSS
Staple horizontal shift motor
FNMRPN
Alignment unit paddle rotation motor
FNMS
Oscillation motor
FNMSLS
Staple-free staple motor
FNMSS
Staple motor
No,/Display item
Content
FNCDP
Paddle drive clutch
FNCDRUS
Oscillation lower roller drive clutch
FNCEDCE
Escape transport drive switch clutch
FNMAR
Rear edge assist motor
FNMB
Buffer motor
FNMDJFN
Alignment unit front alignment plate drive motor
FNMDJRN
Alignment unit rear alignment plate drive motor
FNMDT
Tongue drive motor
FNME
Discharge motor
FNMEC
Entry port transport motor
FNMFECES
Escape/Saddle transport switch flapper motor
FNMFR
Rear edge falling motor
FNMGJFN
Alignment unit front alignment plate lift motor
FNMGJRN
Alignment unit rear alignment plate lift motor
FNMGMT
Load paper tray lift motor
FNMGPN
Alignment unit paddle lift motor
FNMGRS
Take-up switch roller lift motor
FNMJF
Front alignment motor
FNMJR
Rear alignment motor
FNMMSS
Staple horizontal shift motor
FNMRPN
Alignment unit paddle rotation motor
FNMS
Oscillation motor
FNMSLS
Staple-free staple motor
FNMSS
Staple motor
FSMC
Saddle transport motor
FSMDLE
Saddle switch lever drive motor
FSME
Saddle discharge motor
FSMF
Saddle folding motor
FSMG
Saddle gripper motor
FSMJ
Saddle alignment motor
FSMS
Saddle staple motor
FSMSR
Saddle rear edge stopper motor
No,/Display item
Content
FCMR
Punch horizontal registration motor
FCP
Punch hole motor
No,/Display item
Content
PDPTM
Relay unit transport motor
No,/Display item
Content
Item/Display
Content
Setting
range
Default
value
A
ALIGNMENT
Alignment position
adjustment
adjustment
50 - 150
100
B
ALIGNMENT
CENTER
CENTER
Alignment position center
adjustment
adjustment
90 - 110
100
C
STAPLE
FRONT
FRONT
Stapling position
adjustment (one position in
front)
adjustment (one position in
front)
50 - 150
100
D
STAPLE REAR
Stapling position
adjustment (one position at
the rear)
adjustment (one position at
the rear)
50 - 150
100
E
STAPLE BOTH
Stapling position
adjustment (staple pitch of
two positions binding)
adjustment (staple pitch of
two positions binding)
50 - 150
100
F
MANUAL
STAPLE
POSITION
STAPLE
POSITION
Manual stapling position
adjustment 80
adjustment 80
-
120
100
G
STAPLELESS
STAPLE Y
STAPLE Y
Staple-free stapling
position adjustment (Y :
Main scanning direction)
position adjustment (Y :
Main scanning direction)
70 - 130
100
H
STAPLELESS
STAPLE X
STAPLE X
Staple-free stapling
position adjustment (X :
Sub scanning direction)
position adjustment (X :
Sub scanning direction)
85 - 115
100
I
STAPLELESS
STAPLE
PRESSURE
STAPLE
PRESSURE
Staple-free stapling
welding pressure
adjustment (Motor rotation)
welding pressure
adjustment (Motor rotation)
85 - 115
100
J
BELT
PRESSURE
PRESSURE
Return belt pressure
adjustment
adjustment
90 - 110
100
K
MANUAL
STAPLE TIME
STAPLE TIME
Manual staple time out
setting
setting
1 - 5
2
L
MANUAL
STAPLE
PULLOUT
TIME
STAPLE
PULLOUT
TIME
Manual staple pull out time
out setting
out setting
0 - 10
0
M
PUNCH X
Punch hole position
adjustment (X : Sub
scanning direction)
adjustment (X : Sub
scanning direction)
80 - 120
100
Item/Display
Content
Setting
range
Default
value
A
STAPLE
POSITION
POSITION
Stapling position
adjustment
adjustment
93 - 107
100
B
JOGGER(A3)
Jogger position adjustment
A3
A3
97 - 103
100
C
JOGGER(B4)
Jogger position adjustment
B4
B4
97 - 103
100
D
JOGGER(A4-
R)
R)
Jogger position adjustment
A4-R
A4-R
97 - 103
100
E
JOGGER(A4)
Jogger position adjustment
A4
A4
97 - 103
100
F
JOGGER(B5-
R)
R)
Jogger position adjustment
B5-R
B5-R
97 - 103
100
G
JOGGER(B5)
Jogger position adjustment
B5
B5
97 - 103
100
H
JOGGER(11 x
17)
17)
Jogger position adjustment
11 x 17
11 x 17
97 - 103
100
I
JOGGER(8.5 x
14)
14)
Jogger position adjustment
8.5 x 14
8.5 x 14
97 - 103
100
J
JOGGER(8.5 x
11R)
11R)
Jogger position adjustment
8.5 x 11R
8.5 x 11R
97 - 103
100
K
JOGGER(8.5 x
11)
11)
Jogger position adjustment
8.5 x 11
8.5 x 11
97 - 103
100
L
JOGGER(12 x
18)
18)
Jogger position adjustment
12 x 18
12 x 18
97 - 103
100
M
JOGGER(8KR)
Jogger position adjustment
8K
8K
97 - 103
100
N
JOGGER(16K-
R)
R)
Jogger position adjustment
16K-R
16K-R
97 - 103
100
O
JOGGER(16K)
Jogger position adjustment
16K
16K
97 - 103
100
P
JOGGER(OTH
ER)
ER)
Jogger position adjustment
Other
Other
97 - 103
100
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man6) service manuals if exist.