Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man6) Service Manual ▷ View online
MX-4070V SIMULATION 6 – 6
44-37
Used to set the development bias correction
level in the continuous printing operation
level in the continuous printing operation
44-43
Used to display the identification information
of the developing unit
of the developing unit
44-62
Used to set the process control execution
conditions
conditions
46-1
Used to adjust the copy density in the copy
mode
mode
46-2
Used to adjust the copy density in the copy
mode
mode
46-4
Used to adjust the density in the image send
mode
mode
46-5
Used to adjust the density in the image send
mode
mode
46-8
Used to adjust the image send mode color
balance RGB
balance RGB
46-9
Used to adjust the scan image density
3
46-10
Used to adjust the copy color balance and the
gamma (for each color copy mode)
gamma (for each color copy mode)
46-16
Used to adjust the monochrome copy density
and the gamma (for each monochrome copy
mode)
and the gamma (for each monochrome copy
mode)
46-19
Used to set the operating conditions for the
density scanning (exposure) of monochrome
auto copy mode documents
density scanning (exposure) of monochrome
auto copy mode documents
46-21
Copy color balance adjustment (manual
adjustment)
adjustment)
1-3
5
46-23
Used to set the density correction of copy high
density section (high density tone gap
supported)
density section (high density tone gap
supported)
46-24
Copy color balance adjustment (auto
adjustment)
adjustment)
5
46-25
Used to adjust the copy color balance (single
color copy mode)
color copy mode)
46-26
Used to reset the single color mode color
balance set value to the default
balance set value to the default
46-27
Used to adjust the gamma/density of copy
images, text and line image edges
images, text and line image edges
46-30
Used to adjust the resolution in the sub
scanning direction in the copy mode
scanning direction in the copy mode
46-32
Used to adjust the document background
density reproducibility in the monochrome
auto copy mode
density reproducibility in the monochrome
auto copy mode
46-36
Used to adjust the colors in the two color copy
mode
mode
46-37
Used to adjust the reproduction capability of
monochrome mode color
monochrome mode color
46-38
Used to adjust the black component amount
in the color copy mode
in the color copy mode
46-39
Used to adjust the sharpness of FAX send
images
images
46-40
Used to adjust the FAX send image density
(Collective adjustment of all the modes)
(Collective adjustment of all the modes)
46-41
Used to adjust the FAX send image density
(Normal)
(Normal)
46-42
Used to adjust the FAX send image density
(Fine)
(Fine)
46-43
Used to adjust the FAX send image density
(Super fine)
(Super fine)
46-44
Used to adjust the FAX send image density
(Ultra fine)
(Ultra fine)
46-45
Used to adjust the FAX send image density
(600dpi)
(600dpi)
46-46
Used to adjust the FAX send image density
(RGB RIP)
(RGB RIP)
46-47
Used to set the compression rate of copy and
scan images (JPEG)
scan images (JPEG)
46-48
Used to set the copy output resolution of copy
mode
mode
Sim
No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
46-51
Used to adjust the gamma for the copy mode
heavy paper mode and the image process
mode
heavy paper mode and the image process
mode
46-52
Used to set the gamma default for the copy
mode heavy paper and the image process
mode
mode heavy paper and the image process
mode
1-3
46-54
Used to perform the engine halftone
automatic density adjustment (dither)
automatic density adjustment (dither)
1-3
46-55
Used to adjust the drop out color in the image
send mode (monochrome manual text mode)
send mode (monochrome manual text mode)
46-58
Used to set the copy mode pseudo resolution
(smoothing process)
(smoothing process)
46-60
Used to adjust the sharpness in the copy/scan
mode
mode
46-61
Used to adjust the area separation recognition
level
level
46-62
Used to set the operating condition of the ACS
the area separation the background image
process and the auto exposure mode
the area separation the background image
process and the auto exposure mode
46-63
Used to adjust the density in the copy low
density section
density section
46-65
Used to set the color correction table
46-66
Used to adjust the reproduction capability of
watermarks in the copy/printer mode
watermarks in the copy/printer mode
46-68
Used to adjust the auto resolution judgement
(For MX-xx60/xx70 series)
(For MX-xx60/xx70 series)
46-74
Copy color balance adjustment (Auto
adjustment)/printer color balance adjustment
(Auto adjustment)
adjustment)/printer color balance adjustment
(Auto adjustment)
1-1
-5
2-2
-3
1-2
-3
46-90
Used to set the process operation of high
compression PDF images
compression PDF images
46-91
Used to adjust the reproduction capability of
black text
black text
48-1
Used to adjust the scan image magnification
ratio (in the main scanning direction and the
sub scanning direction)
ratio (in the main scanning direction and the
sub scanning direction)
1-1
48-5
Used to correct the scan image magnification
ratio (in the sub scanning direction)
ratio (in the sub scanning direction)
1-1
48-6
Used to adjust the rotation speed of each
motor
motor
49-1
Used to perform the firmware update
4
5
49-3
Used to update the operation manual
4
5
49-5
Used to perform the watermarks update
4
5
49-6
Used to perform the OCR update
49-10
Used to perform the ACU update
50-1
Copy image position, image loss adjustment
1-1
50-5
Used to adjust the print lead edge image
position
position
1-1
50-6
Used to adjust the copy image position and
the image loss (SPF mode)
the image loss (SPF mode)
1-1
50-10
Used to adjust print image position
1-2
2-1
1-1
50-12
Used to perform the scan image off center
position adjustment
position adjustment
1-1
50-20
Image registration adjustment (Main scanning
direction)
direction)
1-2
50-22
Used to adjust the image registration (Main
scan direction, sub scan direction)
scan direction, sub scan direction)
1-1
2-1
1-1
-2
50-23
Used to set the registration for temperature
adjustment
adjustment
50-24
Used to display the detail data of SIM 44-2,
50-20, 21 and 22
50-20, 21 and 22
50-27
Used to perform the image loss adjustment of
scanned images in the FAX or image send
mode
scanned images in the FAX or image send
mode
50-28
Used to automatically adjust the image loss,
void area, image off center and image
magnification ratio
void area, image off center and image
magnification ratio
Sim
No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
MX-4070V SIMULATION 6 – 7
51-1
Used to adjust the ON/OFF timing of the
secondary transport voltage
secondary transport voltage
51-2
Used to adjust the contact pressure
(deflection amount) on paper by the main unit
and the SPF resist roller
(deflection amount) on paper by the main unit
and the SPF resist roller
53-6
Used to adjust the detection level of the SPF
document width
document width
3
53-7
Used to adjust the SPF document size width
sensor
sensor
53-8
Used to adjust the document lead edge
reference and the SPF mode document scan
position
reference and the SPF mode document scan
position
3
53-9
SPF dirt detection setting
53-10
SPF dirt detection execution
55-1
Used to set the specification of the engine
control operations (SOFT SW)
control operations (SOFT SW)
55-2
Used to set the specifications of the scanner
control operation (SOFT SW)
control operation (SOFT SW)
55-3
Used to set the specifications of the controller
operation (SOFT SW)
operation (SOFT SW)
55-10
Used to set the special stamp text for Taiwan
56-1
Used to transport data between HDD - MFP
PWB SRAM/EEPROM
PWB SRAM/EEPROM
56-2
Used to backup the data in the EEPROM and
HDD to the USB memory
HDD to the USB memory
56-3
Used to backup the document filing data to
the USB memory
the USB memory
56-4
Used to backup the JOB log data to the USB
memory
memory
56-5
Used to import the SIM22-6 data to a USB
memory in the text format
memory in the text format
56-6
Used to output the JAM/trouble data
56-7
Used to export system log data to the USB
memory
memory
56-8
Used to perform ICC profile update
56-15
MFP EEPROM data restore
56-99
Used to export system log data to the USB
memory
memory
3-4
1-5
9-4
60-1
Used to check the memory operations (read/
write) of the SCU-MFP PWB
write) of the SCU-MFP PWB
61-1
Used to check the LSU polygon motor rotation
and laser detection
and laser detection
61-3
Used to set the laser power
61-4
Used to print the print image skew adjustment
pattern
pattern
61-11
Used to correct the laser power automatically
2-3
1-2
-3
61-12
Laser power manual correction
61-13
Used to clear the laser power correction value
2-3
1-3
61-14
Used to set the laser power correction
1-3
62-1
Used to format the HDD
62-2
Used to check read/write of the HDD (partial)
62-3
Used to check read/write of the HDD (all
areas)
areas)
62-6
Used to perform the self diagnostics of the
HDD
HDD
62-7
Used to print the HDD self diagnostics error
log
log
62-8
Used to format the HDD
62-10
Used to clear the job completion list data
62-11
Used to delete the document filing data
62-12
Used to set Enable/Disable of auto format in a
HDD trouble
HDD trouble
62-13
Used to format the HDD (Operation manual
watermark data only)
watermark data only)
62-14
Used to delete the document filing
management data
management data
62-20
Used to check the status display of HDD
Sim
No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
63-1
Used to display the shading correction result
63-2
Used to perform shading
1-5
3
63-3
Used to perform scanner (CCD) color balance
and gamma auto adjustment
and gamma auto adjustment
1-5
2-3
3
63-4
Used to display the scanner test chart patch
density
density
63-5
Used to perform the scanner (CCD) color
balance and gamma default setting
balance and gamma default setting
2-3
3
63-7
Used to register the service target of the copy
mode auto color balance adjustment
mode auto color balance adjustment
5
63-8
Used to set the default of the service target of
the copy mode auto color balance adjustment
the copy mode auto color balance adjustment
5
63-11
Used to set the target color balance of the
copy mode auto color balance adjustment
copy mode auto color balance adjustment
5
64-1
Test print (self print) (color mode)
64-2
Test print (self print) (monochrome mode)
8
64-4
Printer test print (self print)
64-5
Printer test print (self print) (PCL)
1-4
64-6
Printer test print (self print) (PS)
65-1
Used to adjust the touch panel (LCD display
section) detection coodinates
section) detection coodinates
7
65-2
Used to display the touch panel (LCD display
section) detection coodinates
section) detection coodinates
65-5
Used to check the operation panel key input
66-1
Used to display the image send-related soft
SW (2-150) on the LCD to allow changing the
soft SW while checking with the LCD
SW (2-150) on the LCD to allow changing the
soft SW while checking with the LCD
2-3
66-2
Used to enter a country code and set the
default value for the country code
default value for the country code
66-3
Used to check read/write of the EEPROM and
the SDRAM on the MODEM controller and
display the result
the SDRAM on the MODEM controller and
display the result
66-4
Used to send the selected signals to the line
and the main unit speaker (send level: max)
and the main unit speaker (send level: max)
66-5
Used to send the selected signal to the line
and the main unit speaker (send level: soft
SW setting)
and the main unit speaker (send level: soft
SW setting)
66-6
Used to print the confidential registration
check table (BOX No, BOX name, passcode
check table (BOX No, BOX name, passcode
66-7
Used to output all image data saved in the
image memory
image memory
66-8
Used to send the selected sound message to
the line and the speaker (send level: max)
the line and the speaker (send level: max)
66-9
Used to send the selected sound message to
the line and the speaker (send level: soft SW
setting)
the line and the speaker (send level: soft SW
setting)
66-10
Used to clear the FAX and image send image
data
data
66-11
Used to send the selected signal at 300bps to
the line and the speaker (send level: max)
the line and the speaker (send level: max)
66-12
Used to send the selected signal at 300bps to
the line and the speaker (send level: soft SW
setting)
the line and the speaker (send level: soft SW
setting)
66-13
Used to register dial number for Sim66-14/15/
16 dial test
16 dial test
66-14
Used to execute the dial pulse (10pps) send
test and to adjust the make time
test and to adjust the make time
66-15
Used to execute the dial pulse (20pps) send
test and to adjust the make time
test and to adjust the make time
66-16
Used to execute the DTMF signal send test
and to adjust the send level
and to adjust the send level
66-17
Used to send the DTMF signal to the line and
the speaker (send level: max)
the speaker (send level: max)
66-18
Used to send the DTMF signal to the line and
the speaker (send level: soft SW setting)
the speaker (send level: soft SW setting)
66-21
Used to print the selected items (system error,
protocol monitor)
protocol monitor)
Sim
No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
MX-4070V SIMULATION 6 – 8
66-22
Used to set the handset sound volume (Japan
model only)
model only)
66-29
Used to initialize the telephone book data
66-30
Used to display the TEL/LIU status change,
the display is highlighted by status change
the display is highlighted by status change
66-31
Used to set ON/OFF the port for output to
TEL/LIU
TEL/LIU
66-32
Used to check the fixed data received from
the line and to display the result
the line and to display the result
66-33
Used to execute detection of various signals
with the line connected and to display the
detection result. When a signal is detected the
display is highlighted
with the line connected and to display the
detection result. When a signal is detected the
display is highlighted
66-36
Used to check send and receive data from the
MODEM controller to the MFP controller or
the data line or the command line individually
MODEM controller to the MFP controller or
the data line or the command line individually
66-39
Used to check and change the destination
setting saved in EEPROM of the FAX BOX
setting saved in EEPROM of the FAX BOX
66-42
Used to rewrite the program to power control
installed in the FAX BOX
installed in the FAX BOX
66-43
Used to write the adjustment value into the
power control installed in the FAX BOX
power control installed in the FAX BOX
66-61
Used to display the image send-related soft
SW (151-250) on the LCD to allow changing
the soft SW while checking with the LCD
SW (151-250) on the LCD to allow changing
the soft SW while checking with the LCD
66-62
Used to import the FAX receive data into a
USB memory in PDF file type
USB memory in PDF file type
67-17
Printer reset
67-24
Printer color balance adjustment (Auto
adjustment)
adjustment)
6
67-25
Printer color balance adjustment (Manual
adjustment)
adjustment)
1-4
6
67-26
Used to set the target color balance of the
printer mode auto color balance adjustment
printer mode auto color balance adjustment
6
67-27
Used to set the service target of the printer
mode auto color balance adjustment
mode auto color balance adjustment
6
67-28
Used to set the default of the service target of
the printer mode auto color adjustment
the printer mode auto color adjustment
6
67-31
Used to clear the printer calibration value
67-33
Used to change the gamma of the printer
screen
screen
67-34
Used to set the density correction in the
printer high density section
printer high density section
67-36
Used to adjust the density in the low density
section
section
67-41
Used to set 2 color print
67-42
Used to set 2 color print color density
67-43
Used to adjust 2 color mode color balance
67-52
Used to set the default of the gamma of the
printer screen
printer screen
1-3
67-54
Printer color balance adjustment
1-3
Sim
No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
MX-4070V SIMULATION 6 – 9
5. Details of simulation
1
1-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the scanner
(reading) unit and the control circuit.
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1) Select the operation speed with the touch panel key.
2) Press [EXECUTE] key.
1) Select the operation speed with the touch panel key.
2) Press [EXECUTE] key.
Scanning is once performed at the speed corresponding to the
scan resolution (operation speed).
scan resolution (operation speed).
RSPF
DSPF
1-2
Purpose
Operation test/check
Function (Purpose)
Used to check the sensors in the scanner
(reading) section and the related circuits.
(reading) section and the related circuits.
Section
Scanner (reading)
Operation/Procedure
The operating status of the sensor is displayed.
When "MHPS" is highlighted, the scanner unit is in the home posi-
tion.
The operating status of the sensor is displayed.
When "MHPS" is highlighted, the scanner unit is in the home posi-
tion.
1-5
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the scanner
(reading) unit and the control circuit.
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1) Select the operation speed with the touch panel key.
2) Press [EXECUTE] key.
1) Select the operation speed with the touch panel key.
2) Press [EXECUTE] key.
Scanning is repeated at the speed corresponding to the scan
resolution (operation speed).
When [EXECUTE] key is pressed, the operation is terminated.
resolution (operation speed).
When [EXECUTE] key is pressed, the operation is terminated.
RSPF
DSPF
2
2-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the auto-
matic document feeder and the control cir-
cuit.
matic document feeder and the control cir-
cuit.
Section
SPF
Operation/Procedure
1)
1)
Select the operation mode and the speed with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The RSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).
When [EXECUTE] key is pressed, the operation is terminated.
The RSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).
When [EXECUTE] key is pressed, the operation is terminated.
RSPF
DSPF
2-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the sen-
sors and the detectors in the automatic
document feeder section and the control
circuits.
sors and the detectors in the automatic
document feeder section and the control
circuits.
Section
Automatic document feeder
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI (372mm/s)
300DPI (372mm/s)
400DPI
400DPI (297mm/s)
600DPI
600DPI (198mm/s)
1200DPI
1200DPI (99mm/s)
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI (372mm/s)
300DPI (372mm/s)
400DPI
400DPI (372mm/s)
600DPI
600DPI (264.0mm/s)
1200DPI
1200DPI (132mm/s)
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI (372mm/s)
300DPI (372mm/
s)
s)
400DPI
400DPI (297mm/s)
600DPI
600DPI (198mm/s)
1200DPI
1200DPI (99mm/s)
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI (372mm/s)
300DPI (372mm/
s)
s)
400DPI
400DPI (372mm/s)
600DPI
600DPI (264.0mm/s)
1200DPI
1200DPI (132mm/s)
Item/Display
Operation mode
Default value
SPF SCAN
(SINGLE)
(SINGLE)
300DPI
300DPI(396.0mm/s)
300DPI
(396.0mm/s)
(396.0mm/s)
400DPI
400DPI(297.0mm/s)
600DPI
600DPI(198.0mm/s)
SPF SCAN
(DOUBLE)
(DOUBLE)
300DPI
300DPI(396.0mm/s)
300DPI
(396.0mm/s)
(396.0mm/s)
400DPI
400DPI(297.0mm/s)
600DPI
600DPI(198.0mm/s)
Item/Display
Operation mode
Default value
SPF SCAN
(SINGLE)
(SINGLE)
300DPI
300DPI(496.0mm/s)
300DPI
(496.0mm/s)
(496.0mm/s)
400DPI
400DPI(396.0mm/s)
600DPI
600DPI(264.0mm/s)
SPF SCAN
(DOUBLE)
(DOUBLE)
300DPI
300DPI(496.0mm/s)
300DPI
(496.0mm/s)
(496.0mm/s)
400DPI
400DPI(396.0mm/s)
600DPI
600DPI(264.0mm/s)
Display
Content
SPED
Document sensor
SPPD1
Document transport sensor 1
SPLS1
Paper size detector 1
SPLS2
Paper size detector 2
SOCD
SPF open/close sensor
SPPD2
Document transport sensor 2
SPPD3
Document transport sensor 3
SPPD4
Document transport sensor 4
SCOV
SPF cover open/close detector
SSET
SPF installation detection
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man6) service manuals if exist.