Sharp MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man10) Service Manual ▷ View online
MX-3640N
MX-PC12/XB16 (PLASMACLUSTER ION GENERATOR/MOUNTING KIT) 28 – 2
3) Turn the adjuster to be grounded.
B.
Fix the Support mounting blacket.
1) Cut off the rear cabinet with the knife, etc.
2) Remove the screw at the rear side of the machine.
Then, fix the step screw A (Packed items No.8 M4) and
the step screw B (Packed items No.9 M4) temporarily.
the step screw B (Packed items No.9 M4) temporarily.
3) Attache the RS-232C cable (Packed items No.3) with the
Support mounting blacket unit.
Fit the edge of the tape of RS-232C cable with the edge
of the lib part.
of the lib part.
4) Fix the Support blacket unit with the step screws.
When PCI unit is removed from the machine, the part which
is cut at step 1) is exposed. When the cut part is exposed, fix
the rear cabinet cover which is served as the service parts
not to be exposed.
Rear cabinet cover : GFTA-0026FCZ1
Fixing screw : XHBS730P06000
is cut at step 1) is exposed. When the cut part is exposed, fix
the rear cabinet cover which is served as the service parts
not to be exposed.
Rear cabinet cover : GFTA-0026FCZ1
Fixing screw : XHBS730P06000
C.
Fix the Power box unit.
1) Remove the screw at the rear side of the machine. Con-
nect the cable of the power box unit with the machine.
2) Put the cable of the pow er box unit through the support
mounting blacket unit. Fix the power box unit with the
step screw C (Packed items No.10 M4).
step screw C (Packed items No.10 M4).
2
1
2
1
2
1
2
1
2
2
2
1
MX-3640N
MX-PC12/XB16 (PLASMACLUSTER ION GENERATOR/MOUNTING KIT) 28 – 3
D.
Fix the PCI unit.
1) Put the PCI bottom cover through the support mounting
blacket unit. Fix the support mounting plate to the sup-
port mounting blacket unit with the screws (Packed items
No. 11 M4 x 45).
port mounting blacket unit with the screws (Packed items
No. 11 M4 x 45).
2) Fix the PCI main unit to the sup port mounting blacket
unit with the coin screw (Pakced items No.12 M4).
E.
Adjust the tilt of PCI main unit.
1) Fix the coin screw (Pakced items No.12 M4) for adj ust-
ing the tilt of the PCI main unit to the bottom of the PCI
main unit.
main unit.
2) Adjust the tilt of the PCI main unit by tightening or loos-
ening the coin screw.
3) Fix the PCI bottom cover to the PCI main unit after finish-
ing the adjustment.
F.
Connect the RS-232C cable.
1) Remove the cap and connect the RS-232C cable with
the machine.
G.
Connect the cable of the Power box unit.
1) Remove the rear cover of the PCI unit.
2) Fix the snap band of the power unit box cable to the PCI
main unit with th e screw (Packed items No.4 M4 x 8).
Connect the Power unit box cable to with the machi ne.
Then, fix the ferrite core to the power unit box cable.
Connect the Power unit box cable to with the machi ne.
Then, fix the ferrite core to the power unit box cable.
1
2
2
3
1
2
A
B
A
B
1
2
2
1
2
3
4
1
MX-3640N
MX-PC12/XB16 (PLASMACLUSTER ION GENERATOR/MOUNTING KIT) 28 – 4
3) Fix the PCI rear cover.
4) Fix the harness cover (Packed items No.6) with winding
the RS-232C cable and the power box unit cable to the
support mounting blacket unit.
support mounting blacket unit.
H.
Turn ON the power of the main unit
1) Connect the RS-232C cable with the machine.
2) Connect the power plug of the machine to the power
outlet, and turn ON the main power switch and the
operation panel power switch.
operation panel power switch.
3)
Enter the SIM26-6 [A] mode for the PCI setting and enter the set
value with 1 or 2 to activate the PCI unit.
value with 1 or 2 to activate the PCI unit.
2
1
MX-3640N Remote operation panel function Enable setting 29 – 1
MX-3640N
Service Manual
[29] Remote operation panel function Enable setting
1. General
To use the remote operation panel function, the password for the
remote operation panel function must be entered on the password
input menu displayed on the VNC boot screen. Note that, therefore,
the password must be set in advance to use the remote operation
panel function.
Let the user make the password, and use SIM26-78 to set it.
Let the user make the password, and use SIM26-78 to set it.
After installation of an option, upgrade all the firmware's to the lat-
est versions.
2. Remote operation panel function
password setting procedures
1) Enter the SIM26-78 mode.
2) Enter the password with 10-key. (Within 5 - 8 digits)
The entered password is displayed on the column of " NEW."
To modify the ente red password, use clear key to delete the
password digit by digit.
3) Press [SET] key, and the password is set.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
523(3$66:25'6(77,1*
35(6(17˖
ǂǂ1(:˖
ǂǂ1(:˖
6(7
Click on the first or last page to see other MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man10) service manuals if exist.