Sharp MX-2614N / MX-3114N (serv.man8) Service Manual ▷ View online
MX-3114N Remote operation panel function Enable setting 25 – 1
MX-3114N
Service Manual
[25] Remote operation panel function Enable setting
1. General
To use the remote operation panel function, the password for the
remote operation panel function must be entered on the password
input menu displayed on the VNC boot screen. Note that, therefore,
the password must be set in advance to use the remote operation
panel function.
remote operation panel function must be entered on the password
input menu displayed on the VNC boot screen. Note that, therefore,
the password must be set in advance to use the remote operation
panel function.
Let the user make the password, and use SIM26-78 to set it.
After installation of an option, upgrade all the firmware's to the lat-
est versions.
est versions.
2. Remote operation panel function
password setting procedures
1)
Enter the SIM26-78 mode.
2)
Enter the password with 10-key. (Within 5 - 8 digits)
The entered password is displayed on the column of "NEW."
To modify the entered password, use clear key to delete the
password digit by digit.
To modify the entered password, use clear key to delete the
password digit by digit.
3)
Press [SET] key, and the password is set.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
523(3$66:25'6(77,1*
35(6(17˖
ǂǂ1(:˖
ǂǂ1(:˖
6(7
MX-3114N Setting, Adjustments, Operation check 26 – 1
MX-3114N
Service Manual
[26] Setting, Adjustments, Operation check
1. Firmware version check and version
up
After installation of all the options to the machine, use SIM22-5 to
check the version of each firmware. If it is not the latest version,
upgrade it to the latest one.
check the version of each firmware. If it is not the latest version,
upgrade it to the latest one.
2. Function and operation check
Check that the following operations are normal.
Check item list
Equipped condition
Key-in (operation panel)
Display (operation panel)
Paper feed
operation
operation
Hand feed
Main unit paper
tray
tray
Desk unit paper
feed tray
feed tray
With the desk unit installed
Paper size detection
Originals size
detection
detection
Original table
mode
mode
RSPF mode
RSPF operation /
two sided copy
two sided copy
S-S mode
D-S mode
S-D mode
D-D mode
Bookbinding operation
When the finisher is installed
Stapling operation
When the finisher is installed
Grouping operation
When the finisher is installed
Sorting operation
When the finisher is installed
Paper exit operation
When the exit tray unit (MX-TR12/
TR13) is installed
TR13) is installed
MX-3114N Setup and adjustment data recording 27 – 1
MX-3114N
Service Manual
[27] Setup and adjustment data recording
Print the various setup data and the adjustment data (list) with
SIM22-6 and keep the data.
SIM22-6 and keep the data.
• In case of a memory trouble, if the data are not kept, all the
adjustments must be made again.
• If the data are kept, the setup values and the adjustment values
can be entered without adjustments, shortening the servicing
time.
time.
MX-3114N Necessary works before moving the machine 28 – 1
MX-3114N
Service Manual
[28] Necessary works before moving the machine
1)
If the following options are installed, remove all of them from
the machine.
the machine.
• Large capacity tray
• Finisher
• Paper pass unit
• Saddle finisher
2)
Remove the following consumable parts from the machine.
• Paper
• Toner cartridges
• Development cartridge
3)
Lock the following sections.
• Scanner (Optical section)
• Paper cassette lift plate
Since the hard disk drive is built in the machine, use care not to
exert vibrations or shocks to the machine when in transit.
exert vibrations or shocks to the machine when in transit.
Click on the first or last page to see other MX-2614N / MX-3114N (serv.man8) service manuals if exist.