Sharp MX-2614N / MX-3114N (serv.man8) Service Manual ▷ View online
MX-3114N AR-SU1 (STAMP UNIT) 11 – 2
4)
Install the sensor cover.
5)
Close the OC mat.
C. RSPF unit attachment
1)
Attach the RSPF unit to the main unit.
2)
Attach the harness guide, and connect the connector.
Place the harness of the scanner home position sensor at the
back of the guide and the RSPF harness. Check to confirm
that the connector of the scanner home position sensor is
securely connected.
back of the guide and the RSPF harness. Check to confirm
that the connector of the scanner home position sensor is
securely connected.
D. Finish stamp cartridge attachment
1)
Open the left cover, and open the document tray.
2)
Attach the finish stamp cartridge.
E. Turn ON the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
F. Installation check
1)
Use SIM22-10 to check to confirm that the finish stamp (AR-
SU1) is recognized.
SU1) is recognized.
1
3
3
2
2
2
1
MX-3114N MX-FX11 (FACSIMILE EXPANSION KIT) 12 – 1
MX-3114N
Service Manual
[12] MX-FX11 (FACSIMILE EXPANSION KIT)
1. Unpacking
A. Packed items check
*: Brazil, South Africa only
2. Installation
Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
A. FAX unit installation
1)
Remove the two screws on the rear cabinet of the main unit.
Attach the step screw (M3) (included in the package) to one of
the removed screw positions.
Attach the step screw (M3) (included in the package) to one of
the removed screw positions.
2)
Hang the Fax unit on the step screw. Fix the Fax unit with the
screws which were removed in the step 1).
screws which were removed in the step 1).
B. Left cabinet and shield plate removal
1)
Remove the left cabinet.
2)
Remove the shield plate.
No.
Name
Quantity
1
Fax unit
1
2
Line cable
1
3
Ferrite core
2
4
Step screw (M3)
1
5
M3 screw
1(2*)
6
Binding band
1*
7
Step screw (M4)
1
8
Line cable
1
2
1
4
3
5
6
8
U.K
France
Germany
Australia
For other destinations
7
2
1
1
2
1
2
1
1
2
2
1
1
MX-3114N MX-FX11 (FACSIMILE EXPANSION KIT) 12 – 2
C. I/F cable connection
1)
Connect the I/F cable to the MFP controller PWB, and fix the
binding band (and FG line (Taiwan, Brazil, South Africa)) with
the M3 screw included in the package.
binding band (and FG line (Taiwan, Brazil, South Africa)) with
the M3 screw included in the package.
Check to confirm that it is securely connected.
(Except Taiwan, Brazil, South Africa)
(Taiwan, Brazil, South Africa)
D. Shield plate and left cabinet attachment
1)
Attach the shield plate.
2)
Attach the left cabinet.
E. Turn ON the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
F. Destination setting
1)
Enter the SIM26-6 mode.
2)
Check to confirm that the destination setting of the machine
matches the specifications of the FAX destination. If not, the
FAX may not function properly.
matches the specifications of the FAX destination. If not, the
FAX may not function properly.
G. Clear theFAX related software switches
1)
Enter the SIM66-2 mode.
2)
Press DEST CODE button.
3)
Take a note of the corresponding destination code.
4)
Press BACK button to return to the code entry mode.
5)
Enter the destination code taken in procedure 3), and press
SET button.
SET button.
6)
Press EXECUTE and YES buttons.
H. Line cable connection
1)
Connect the line cable on the line to the modular jack indicated
as “LINE.”
as “LINE.”
When connecting the line cable (to LINE or TEL), wind the line
cable two turns or one turn around the included ferrite core as
shown in the figure, and connect to the modular jack which is
marked with “LINE.”
cable two turns or one turn around the included ferrite core as
shown in the figure, and connect to the modular jack which is
marked with “LINE.”
After connection, perform the setting of “External telephone con-
nection” of the system setting (administrator).
nection” of the system setting (administrator).
2
1
2
1
1
2
2
1
2
Except Taiwan, Brazil,
South Africa
South Africa
Taiwan, Brazil,
South Africa
South Africa
About
10 cm
10 cm
2 turns
About
10 cm
10 cm
1 turn
MX-3114N MX-FN17 (FINISHER) 13 – 1
MX-3114N
Service Manual
[13] MX-FN17 (FINISHER)
1. Unpacking
A. Packed items check
2. Installation
Check to confirm that the firmware version is later than below.
If the version is older, upgrade the firmware.
If the version is older, upgrade the firmware.
Firmware version: 01.07.03.00
Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
A. Paper holding arm and paper exit full detection
actuator removal
1)
Remove the paper holding arm.
The paper holding arm must be removed together with the
paper holding arm holder. Since the paper holding arm is easy
to remove alone, be careful not to leave the paper holding arm
holder unremoved.
paper holding arm holder. Since the paper holding arm is easy
to remove alone, be careful not to leave the paper holding arm
holder unremoved.
2)
Remove the paper exit full detection actuator.
No.
Name
Quantity
1
Finisher
1
2
Attachment
1
3
Blinding bottom plate
1
4
Front rail guide
1
5
Path guide
1
6
Open/Close cover
1
7
Left rear cover
1
8
Punch F cover
1
9
Fulcrum upper cover
1
10
Take-up roller
1
11
Screw (M4 x 10 S tight)
1
12
Screw (M3 x 6 S tight, with flange)
4
13
Screw (M4 x 7 S tight)
5
14
Screw (M3 x 6 S tight)
3
15
Clip
1
16
Fulcrum shaft
1
17
Staple position label (For the scanner)
1
18
Staple position label (For the RSPF)
1
19
Safety cover
1
20
Protection sheet
1
11
12
13
14
15
16
17
18
19
20
2
1
4
3
5
8
9
10
6
7
Click on the first or last page to see other MX-2614N / MX-3114N (serv.man8) service manuals if exist.