Sharp MX-2614N / MX-3114N (serv.man8) Service Manual ▷ View online
MX-3114N Dehumidifying heater 3 – 11
(3)
Rear cabinet and right rear cabinet removal
1)
Remove the rear cabinet and the right rear cabinet.
(4)
Heater harness attachment
1)
Attach the snap band of the heater harness to the frame.
Fix the earth wire to the frame with a screw (M4 x 8).
Fix the earth wire to the frame with a screw (M4 x 8).
(5)
Heater harness 2 attachment
1)
Remove the mounting plate.
2)
Remove the connector cover.
3)
Attach the edge saddle. Attach the heater harness 2, and pass
it through the edge saddle.
Pass the earth wire through the edge saddle, and fix it with a
screw (M4 x 8).
it through the edge saddle.
Pass the earth wire through the edge saddle, and fix it with a
screw (M4 x 8).
4)
Attach the connector cover.
5)
Attach the mounting plate.
1
1
1
1
2
3
1
2
1
1
1
2
2
1
1
3
2
1
2
2
2
2
1
MX-3114N Dehumidifying heater 3 – 12
6)
Attach the clamp to the 1CS drive unit.
Pass the heater harness 2 through the clamp, and attach the
snap band to the 2CS drive unit.
Connect the heater harness and the heater harness 2.
Pass the heater harness 2 through the clamp, and attach the
snap band to the 2CS drive unit.
Connect the heater harness and the heater harness 2.
(6)
Paper feed tray removal
1)
Pull out the paper feed tray, and lift it to remove.
(7)
Tray 2 heater unit attachment
1)
Pass the harness of the heater unit for the tray 2 through the
hole in the frame. Attach the heater unit for the tray 2 to the
frame, and fix it with a screw (M3 x 6).
hole in the frame. Attach the heater unit for the tray 2 to the
frame, and fix it with a screw (M3 x 6).
2)
Attach the clamp to the frame. Connect the harness of the
heater unit for the tray 2 to the heater harness, and pass it
through the clamp.
heater unit for the tray 2 to the heater harness, and pass it
through the clamp.
3)
Attach the high temperature caution label to the paper feed
tray 2.
tray 2.
(8)
Tray 3/4 heater unit attachment
1)
Pass the harness of the heater unit for the tray 3/4 through the
hole in the frame. Attach the heater unit for the tray 2 to the
frame, and fix it with a screw (M3 x 6).
hole in the frame. Attach the heater unit for the tray 2 to the
frame, and fix it with a screw (M3 x 6).
2
1
1
2
2
2
2
1
MX-3114N Dehumidifying heater 3 – 13
2)
Attach the clamp to the frame. Connect the harness of the
heater unit for the tray 3/4 to the frame, and pass it through the
clamp.
heater unit for the tray 3/4 to the frame, and pass it through the
clamp.
3)
Attach the high temperature caution label to the frame.
(9)
Connector connection
1)
Remove the rear cabinet cover of the machine.
2)
Connect the heater harness to the machine harness.
3)
Attach the rear cabinet cover of the machine.
(10) Right rear cabinet and rear cabinet attachment
1)
Attach the right rear cabinet and the rear cabinet.
(11) Paper feed tray attachment
1)
Attach the paper feed tray.
E. Operation check after installation
1)
Turn on the dehumidifier heater switch.
2)
Measure the resistance value between the earth terminal and
the AC terminal (L side), and between the earth terminal and
AC terminal (N side) with the circuit tester, and confirm they
are not short-circuited.
the AC terminal (L side), and between the earth terminal and
AC terminal (N side) with the circuit tester, and confirm they
are not short-circuited.
3)
When not using the dehumidifier heater after checking, turn off
the dehumidifier heater switch.
the dehumidifier heater switch.
1
2
2
1
3
3
3
3
2
1
MX-3114N MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 – 1
MX-3114N
Service Manual
[4] MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER
DRAWER)
1. Unpacking
If the connector is removed first, it may be damaged during the
installation procedures. Therefore, keep it packed while un-box-
ing. and unpack it only when connecting the connector to the
machine.
installation procedures. Therefore, keep it packed while un-box-
ing. and unpack it only when connecting the connector to the
machine.
A. Packed items check
2. Installation
Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
A. Adjuster attachment
1)
Turn each adjuster to fix the desk unit.
B. Main unit and desk unit connection
1)
Put the main unit on the desk unit.
Use man power of four persons or more to lift the main unit.
Place the main unit on the desk unit slowly by fitting the exter-
nal lines. Check to insure that the positioning pin on the top of
the desk unit is securely engaged in the positioning groove of
the main unit.
nal lines. Check to insure that the positioning pin on the top of
the desk unit is securely engaged in the positioning groove of
the main unit.
2)
Remove the tray 1 and the tray 2.
No.
Name
Quantity
1
Desk unit
1
2
Fixing screws (M3 x 8)
4
3
Connection cover
2
1
3
2
Click on the first or last page to see other MX-2614N / MX-3114N (serv.man8) service manuals if exist.