DOWNLOAD Sharp MX-2614N / MX-3114N (serv.man8) Service Manual ↓ Size: 31.51 MB | Pages: 95 in PDF or view online for FREE

MX-3114N  MX-2314N/2614N/3114N (MAIN UNIT)  2 – 6

4)

Move the PTC cleaning rod back and forth a few times to clean
the PTC wire.

After completion of cleaning, insert the cleaning rod completely
to the bottom.

5)

Return the LSU cleaning rod to the front cabinet so that the felt
faces upward. Fit the boss, and fix it with three pawls.

6)

Close the front cabinet.

1)

Press the [SYSTEM SETTINGS] key.

2)

Touch the [Paper Tray Settings] key.

3)

Touch the [Paper Tray Settings] key to configure the settings.
These settings specify the paper type, paper size, and func-
tions allowed for each paper tray. When the [Tray Settings] key
is touched, a list appears showing the trays and the current
settings.

4)

Touch the [Change] key in the above screen to change the set-
tings. The following settings can be configured.

1)

Pull out the paper tray.

Gently pull the tray out until it stops.

If paper remains in the tray, remove it.

2)

Adjust the guide plates A and B by squeezing their lock levers
and sliding them to match the vertical and horizontal dimen-
sions of the paper to be loaded.

The guide plates A and B are slidable. Slide each guide plate
while squeezing its lock lever.

Type

Select the type of paper that is loaded in the tray. 
The paper types that can be selected vary by paper 
tray.

Size

Select the paper size from the list. The paper sizes 
that can be selected vary by tray. The sizes that 
can be selected may also be restricted by the paper 
type selected above. 
If the desired size does not appear in the list, select 
[Custom Size] and directly enter the size (only for 
the bypass tray).

Feeding Approved 
Job

Select the modes that can be used. If there is a 
function that you do not wish to be used with the 
selected tray, disable the function. When the "Type" 
is other than plain paper, recycled paper, colored 
paper, or a user type, [Fax] and [Internet Fax] 
cannot be selected.

A

B

MX-3114N  MX-2314N/2614N/3114N (MAIN UNIT)  2 – 7

Use simulation 26-6 to set the machines destination.

After completion of destination settings, change the set values to
customize the following settings.

Execute the following items.

*1: When a printer option is installed, be sure to execute the above
item.

This adjustment performs the print engine image distortion adjust-
ment, the OPC drum phase adjustment, and the color registration
adjustment simultaneously.

1)

Enter SIM50-22 mode.

26

6

Used to set the destination.

26

3

Used to set the auditor specification mode.

5

Used to set the count mode of the total counter and 
the maintenance counter.

18

Used to set YES/NO of the toner save mode (Only 
in UK and Japan versions)
* For other destination versions, this setup is 

made by the user program.

52

Used to set YES/NO of counting when non-print 
paper is passed through each counter.

53

Used to set YES/NO of user calibration permission.

65

Used to set the limit number of sheets for stapling.

1

Print engine image distortion adjustment (Manual 
adjustment) / OPC drum phase adjustment 
(Automatic adjustment) / Color registration 
adjustment (Automatic adjustment)

50-22

2

Copy color balance and density check

3

Printer color balance/density check

64-5/67-25

4 

*1

Copy/Printer color balance and density adjustment 
(Automatic adjustment)

46-74

EXECUTE

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872$'-8670(172)5(*,675$7,21 '580326,7,21

12:(;(&87,1*

(;(&87(

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872$'-8670(172)5(*,675$7,21 '580326,7,21

35(66>(&(;87(@7267$57

(55257211(5(037<

(;(&87(

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872$'-8670(172)5(*,675$7,21 '580326,7,21

0$,1)0$,1568%6.(:3+$6(

&/1*

0/1*

</1*

$//B527$7(/2.

(;(&87(

Adjustment completed

Abnormal end

MX-3114N  MX-2314N/2614N/3114N (MAIN UNIT)  2 – 8

2)

Press [EXECUTE] key.

[EXECUTE] key is highlighted and the image registration auto-
matic adjustment is started. (It takes about 15 sec to complete
the adjustment.)

3)

When the adjustment is completed, [EXECUTE] key returns to
the normal display, and the value of the adjustment result is
displayed.

The current skew level for each color is displayed on the
SKEW display section.

4)

Write down the displayed skew level. 
(Meaning of the skew level value and the adjustment proce-
dure)

* If "OK" is displayed for all items of SKEW ALL_ROTATE, C, 

M, and Y, there is no need to perform the adjustment.

* When "R" is displayed at the head of the value, turn the LSU 

skew adjustment screw clockwise.

* When "L" is displayed at the head of the value, turn the LSU 

skew adjustment screw counterclockwise.

* The turning amount of the adjustment screw corresponds to 

each adjustment value. "ALL_ROTATE" indicates the num-
ber of rotations, and C, M, and Y indicate numbers of clicks.

The display value is rounded at the decimal point.

* "ALL_ROTATES" shows the number of rotations of adjust-

ments for all the adjustment screws. "C, M, and Y(SKEW)" 
shows the number of adjustment click steps for each adjust-
ment screw of C, M, and Y.

Contents in (    )

MIAN, SUB: Difference from the previous adjustment value of
image registration.

Example: 

If 105 for this time and 103 for the previous time, 
it is displayed as 105.0 (+2.0).

SKEW, ALL_ROTATE: Judgment of the LSU skew adjustment
result. OK or NG.

PHASE: OPC drum phase adjustment value of the previous
time

MAIN F

C

Registration adjustment value main scanning 
direction (Cyan laser writing position F side)

1.0 - 199.0

100

M

Registration adjustment value main scanning 
direction (Magenta laser writing position F side)

1.0 - 199.0

100

Y

Registration adjustment value main scanning 
direction (Yellow laser writing position F side)

1.0 - 199.0

100

MAIN R

C

Registration adjustment value main scanning 
direction (Cyan laser writing position R side)

1.0 - 199.0

100

M

Registration adjustment value main scanning 
direction (Magenta laser writing position R side)

1.0 - 199.0

100

Y

Registration adjustment value main scanning 
direction (Yellow laser writing position R side)

1.0 - 199.0

100

SUB

C

Registration adjustment value sub scanning direction 
(Cyan drum 

 Black drum)

1.0 - 199.0

100

M

Registration adjustment value sub scanning direction 
(Magenta drum 

 Black drum)

1.0 - 199.0

100

Y

Registration adjustment value sub scanning direction 
(Yellow drum 

 Black drum)

1.0 - 199.0

100

SKEW

C

Print skew amount calculation result (Cyan)

-99.9 - 99.9

0

If the value is positive (+), "L" is displayed at the head of the 
value. If negative (–), "R" is displayed.
If the value is in the range of –2.1 - +2.1, "(OK)" is displayed at 
the bottom of the value. In the other cases, "(NG)" is displayed.

M

Print skew amount calculation result (Magenta)

-99.9 - 99.9

0

Y

Print skew amount calculation result (Yellow)

-99.9 - 99.9

0

ALL_

ROTATE

Print skew amount calculation result (Overall)

-99.9 - 99.9

0

If the value is positive (+), "L" is displayed at the head of the 
value. If negative (–), "R" is displayed.
If the value is in the range of –1.6 - +1.6, "(OK)" is displayed at 
the bottom of the value. In the other cases, "(NG)" is displayed.

PHASE

OPC drum phase adjustment value

1 - 8

1

MX-3114N  MX-2314N/2614N/3114N (MAIN UNIT)  2 – 9

5)

If the display of ALL_ROTATE is NG, turn all the LSU skew
adjustment screws to adjust, and perform the procedures 2) to
4).

Repeat the procedures 2) to 5) until the display of
ALL_ROTATE becomes OK. If the display of ALL_ROTATE is
OK, go to the procedure 6).

For the adjustment, remove the front cover and the waste
toner box, and turn the skew adjustment screw.

6)

Repeat the procedures 2) to 4) again, and check to confirm
that C, M, and Y (SKEW) are OK.

If any of them is NG, turn the LSU skew adjustment screw of
the corresponding color to adjust.

When the adjustment is made by turning the LSU skew adjustment
screw of K, the states of C, M and Y (SKEW) are changed. Execute
SIM50-22 to check to confirm that C, M, and Y (SKEW) are OK.

When an abnormality occurs, "ERROR" is displayed.

In this case, check each drive section and the process section.

Before checking the copy color balance and density, be sure to
execute the following jobs.

* Execute the high density image correction (Process correction)

forcibly. (SIM 44-6)

* Execute the half-tone image correction forcibly. (SIM 44-26)

Make a copy of the gray test chart (UKOG-0162FCZZ) and a copy
of the servicing color test chart (UKOG-0326FCZZ/UKOG-
0326FC11), and check that they are proper.

a. Note for execution of the color balance and density check in the
color copy mode

To check the copy color balance and density, use the gray test
chart (UKOG-0162FCZZ) and the servicing color test chart
(UKOG-0326FCZZ/UKOG-0326FC11). Set the copy density
level to "3" in the Text/Printed Photo mode (Manual), and make a
copy.

At that time, all the color balance adjustments in the user adjust-
ment mode must be set to the default (center).

In addition, be sure to use the specified paper for color.

b. Note for checking the monochrome copy mode density

To check the density, use the gray test chart (UKOG-0162FCZZ).
Set the copy density level to "Manual 3" in the Text/Printed Photo
mode (Manual).

In addition, all the color balance adjustments in the user adjust-
ment mode must be set to the default (center).

[Check with the gray test chart (UKOG-0162FCZZ)]

In the copy density check with the gray test chart, check to insure
the following conditions.

For the color (gray) balance, use the servicing color test chart
(UKOG-0326FCZZ/UKOG-0326FC11) to check.

[Check with the servicing color test chart (UKOG-0326FCZZ/
UKOG-0326FC11)]

In the copy color balance check with the servicing color test chart,
check to insure the following conditions.

1

2

3

4

5

6

7

8

9

10

W

SHARP GRAY CHART

SHARP gray chart

Patch 1 is
slightly copied.

Patch 2 is copied.

(Color copy)

1

2

3

4

5

6

7

8

9

10

W

SHARP GRAY CHART

SHARP gray chart

Patch 1 is not copied.

Patch 2 is
slightly copied.

Patch 3 is copied.

(

py)

Serviceman chart (Color patch section)

The densities of patches 1 - 6 of
each color are properly balanced.

Patch 7 is slightly
copied or not copied.

(Color copy)