Sharp MX-2614N / MX-3114N (serv.man8) Service Manual ▷ View online
MX-3114N MX-FN17 (FINISHER) 13 – 2
B. External fixture removal
1)
Open the front cabinet, and remove the front cabinet upper.
2)
Remove the paper exit cover.
3)
Remove the paper exit tray.
4)
Remove the left cabinet.
5)
Remove the left cabinet upper.
C. Packed items attachment
1)
Attach the safety cover to the attachment, and fix it with the
screw (M3 x 6 S tight, with flange).
screw (M3 x 6 S tight, with flange).
2)
Attach the attachment.
2
1
1
2
1
2
1
2
MX-3114N MX-FN17 (FINISHER) 13 – 3
3)
Hold the rib of the paper exit shifter with the fixing guide, fit it to
the notch in the attachment, and fix it with the screw (M4 x 10
S tight).
the notch in the attachment, and fix it with the screw (M4 x 10
S tight).
4)
Cut the front cabinet upper.
5)
Attach the front cabinet upper.
6)
Attach the blind bottom plate and fix it with the screw (M3 x 6 S
tight, with flange).
tight, with flange).
7)
Attach the path guide and fix it with the screw (M3 x 6 S tight,
with flange).
with flange).
8)
Attach the front rail guide and fix it with the screw (M4 x 7 S
tight, M3 x 6 S tight, with flange).
tight, M3 x 6 S tight, with flange).
9)
Attach the punch F cover and fix it with the screw (M3 x 6 S
tight).
tight).
1
2
1
2
1
2
1
2
3
MX-3114N MX-FN17 (FINISHER) 13 – 4
10) Insert the open/close cover into the fulcrum shaft, and fix it with
the clip.
11) Attach the fulcrum cover and fix it with the screw (M3 x 6 S
tight).
12) Attach the protection sheet to the bottom of the operation
panel.
D. External fixture attachment
1)
Remove the left cabinet upper rear from the left cabinet upper.
2)
Attach the left cabinet upper.
3)
Attach the left cabinet.
4)
Attach the take-up roller and fix it with the screw (M4 x 7 S
tight).
tight).
1
2
3
1
2
Edge reference
0 - 3mm
0 - 3mm
R end reference
0 - 3mm
0 - 3mm
1
2
1
2
1
2
MX-3114N MX-FN17 (FINISHER) 13 – 5
E. Finisher attachment
1)
Remove the package supporting plate from the finisher.
2)
Pull out the rail on the R side of the finisher. Check to confirm
that the slide roller is in the rail groove, and insert the finisher
and insert the rail on the R side into the attachment plate pin.
that the slide roller is in the rail groove, and insert the finisher
and insert the rail on the R side into the attachment plate pin.
3)
Fix the rail on the R side with the screw (M4 x 7 S tight).
When attaching the rail on the R side, lift it slightly so that
there is no clearance between the rail on the R side and the
machine frame.
there is no clearance between the rail on the R side and the
machine frame.
4)
Attach the left rear cover, and fix it with the screw (M4 x 7 S
tight).
tight).
Check to confirm that the I/F cable is in the concave section in
the left rear cover.
the left rear cover.
F. Connector connection
1)
Remove the protection material and the fixing tape from the
connector.
connector.
2)
Remove the connector cover of the machine.
3)
Connect the connector of the finisher to the machine, fix it with
the screw.
the screw.
2
1
1
1
2
3
1
2
1
2
2
1
2
1
2
1
2
Click on the first or last page to see other MX-2614N / MX-3114N (serv.man8) service manuals if exist.