Sharp AR-PN1 Service Manual ▷ View online
AR-FN7/PN1 UNPACKING AND INSTALLATION-5
4) Remove the upper cover.
<1>Remove three fixing screws of the upper cover, and remove the
<1>Remove three fixing screws of the upper cover, and remove the
upper cover.
<2>Disengage four pawls of the removed upper cover, and separate it
into upper and lower portions, and reuse the upper portion.
5) Install the punch unit.
<1>Insert two bosses of the punch unit into the boss holes of the finisher,
and fix the unit with three fixing screws.
Note: Use one fixing screw which is packed together and two fixing
screws which were removed in procedure 4).
6) Connect the punch unit harness to the finisher PWB.
<1>Remove the clamp which is fixing the harness. Wire the harness A
<1>Remove the clamp which is fixing the harness. Wire the harness A
(purple) and harness B (orange) as shown in the figure, and fix them
with the clamp.
7) Install the covers which were removed.
<1>Hang two pawls of the upper cover on the unit and fix it with three
<1>Hang two pawls of the upper cover on the unit and fix it with three
fixing screws.
<2>Pass the interface harness of the rear cabinet, and fix with three
screws.
Upper cover
Fixing screw
Fixing screw
Upper cover
Fixing screw
Fixing screw
Boss
Boss
Boss hole
Boss hole
Punch unit
Fixing screw
(Items packed together)
Harness A (purple)
Harness A (purple)
Harness B (orange)
Harness B (orange)
Clamp
Clamp
1
Upper cover
Fixing screw
Fixing screw
Fixing screw
2
Rear cabinet
Interface harness
Interface harness
removing port
Fixing screw
Fixing screw
+ ! #$! %&'(
AR-FN7/PN1 UNPACKING AND INSTALLATION-6
<3>Install the front cabinet to the original position, push the staple unit
into the machine, and fix it with four fixing screws.
*
When installing, insert the projection (B) of the lock release lever into
the latch arm hole (C).
*
After installation, release the latch and move the lever to check that it
slides smoothly.
*
If it does not move smoothly, disengage the pawl on the lower side of
the release lever with a screwdriver (-) and remove the lever. Then
the release lever with a screwdriver (-) and remove the lever. Then
insert is again.
<4>Install the jam process dial, and close the front cover.
8) Install the right front cover of the finisher.
<1>Install the front cover with four fixing screws.
<1>Install the front cover with four fixing screws.
<2>Install the stand cover with three fixing screws, and install the sub
cover with one fixing screw.
9) Attach the dust box label to the upper cover.
<1>Attach the dust box cover to the position shown in the figure below.
10) Connect the connector to the paper feed desk, and connect the AC
cord of the power unit to the printer.
<1>Connect the connector of the interface harness of the finisher to the
paper feed desk, and tighten the connector fixing screw.
<2>Connect the AC cord of the power unit to the inlet connector of the
printer as shown in the figure.
11) Turn on the main switch of the printer.
<1>Insert the power plug of the printer to the power outlet.
<2>Turn on the main switch of the printer.
3
Staple unit
Front cabinet
Fixing screw
Fixing screw
Latch arm
Pawl (D)
Lock release lever (A)
Projection (B)
Jam process dial
Front cover
Fixing screw
Fixing screw
Stand cover
Sub cover
Fixing screw
Fixing screw
Fixing screw
Fixing screw
AC cord
Connector
Fixing screw
"ON"
, ! #$! %&'(
COPYRIGHT © 2001 CANON INC.
2001 2001 2001 2001
CANON SADDLE FINISHER G1 REV.0 MAR. 2001
CHAPTER 2
OUTLINE OF OPERATION
#ChapterCover.p65
3/28/01, 12:05 PM
2
2-1
COPYRIGHT © 2001 CANON INC.
2000 2000 2000 2000
CANON SADDLE FINISHER G1 REV.0 MAR. 2001
CHAPTER 2 OUTLINE OF OPERATION
1 Basic Operations
1.1 Specifications
The finisher serves to deliver sheets coming from its host machine. The mode of delivery
may be non-sort stack, job offset*, or staple delivery.
The saddle unit built into the finisher is used to fold a stack of sheets coming from the fin-
isher unit in half for delivery.
All these operations are controlled by various commands sent by the host machine in ad-
dition to the commands from the finisher controller PCB.
The puncher unit (option) is designed for installation to the pickup assembly of the fin-
isher, and is used to punch holes in sheets coming from the host machine.
The above operations are controlled with various commands from the finisher controller
PCB as well as the commands from the punch controller PCB.
Puncher unit drive
system (puncher unit;
option)
system (puncher unit;
option)
Alignment drive system
Stapler drive system
Delivery drive system
Feed drive system
Tray drive system
Saddle unit
drive system
Control system
F02-101-01
The position of delivery is shifted to the front/rear for each stack to assist
sorting.
sorting.
Chap02.p65
3/28/01, 12:07 PM
1
Click on the first or last page to see other AR-PN1 service manuals if exist.