AR-PE2 (serv.man8). ARPX3 Parts Guide — Sharp Copying Equipment Parts Guide (repair manual)

Model
AR-PE2 (serv.man8)
Pages
8
Size
575.07 KB
Type
PDF
Document
Parts Guide
Brand
Device
Copying Equipment / ARPX3 Parts Guide
File
ar-pe2-sm8.pdf
Date

View Sharp AR-PE2 (serv.man8) Parts Guide online

CONTENTS
SHARP CORPORATION
Parts marked with “
” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SERVICE MANUAL
CODE: 00ZARPX3//A1E
PRINTER I/F KIT
AR-PE2
AR-PX3
MODEL
AR-PX4
[1] OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[2] SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
PARTS GUIDE
– 1 –
[1] OUTLINE
This unit is used to connect the printer controller with the scanner and
the printer section in the AR-C160.
1. Unit composition
This unit is composed of the following major parts:
AR-PE2
• Controller
• I/F card
• Connection cable
AR-PX3/PX4
• Power supply unit
2. Outline of operations
(Printer mode)
Each color image data of 8bit of Y/M/C/K outputted from the print con-
troller.
(Scanner mode)
Each color image data of R/G/B scanned by the scanner is inputted to
the printer I/F card.
(Circuit system)
High-speed data transmission/reception is performed between the en-
gine and the print controller.
[2] SETUP
Necessary tools: Screwdriver
1. Unpacking
(Parts list)
AR-PE2
AR-PX3/PX4
2. Parts assembly
1) Remove the operation unit.
Left side
Right side
2) Remove the left and right upper cabinet.
3) Remove the ICU PWB shield plate.
4) Remove the CCD flat cable connector.
No.
Part name
Quantity
1
Controller
1
2
I/F card
1
3
Flat cable
1
4
Wake up harness
1
No.
Part name
Quantity
1
Power supply unit
1
2
Screw (M4)
8
3
Caution label (Only EU)
1
FOR USE WITH COMPATIBLE SHARP COPIERS.
SEE SHARP COPIER INSTALLATION MANUAL TO DETERMINE SUITABILITY.
AR-PE2/PX3/PX4 Installation Manual
– 2 –
5) Open the scanner (reading) unit and fix it with the hold shaft.
6) Remove the interface cabinet.
7) Remove the cover plate on rear cabinet.
Removed screw is used for attach the printer I/F card.
8) Connect engine side I/F cable.
9) Attach the printer I/F card with the accessory screw, and connect
the wake up signal harness and clock harness.
10) Attach the printer power supply unit, and connect printer PS cable.
Wake up signal harness
Clock harness
– 3 –
11) Remove the top cover of the printer controller and attach the
printer controller.
12) Connect controller side I/F cable and DC cable.
13) Attach the top cover of the printer controller.
14) Install all the parts that were removed to their original positions.
15) Attach the caution label to the cabinet. (Only EU version)
3. Setting
1) Turn on the power of the unit.
2) Enter the simulation 26-1 mode.
3) Press "PRN: AR-PE2" button. (Communication between the unit
and the printer controller is allowed.)
4) Cancel the simulation mode.
Page of 8
Display

Download Sharp AR-PE2 (serv.man8) Parts Guide

Here you can view online or download Sharp AR-PE2 (serv.man8) Parts Guide in pdf. This Parts Guide can help you recover, restore, fix, disassemble and repair Sharp AR-PE2 (serv.man8) Copying Equipment. Information contained in Sharp AR-PE2 (serv.man8) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).