Sharp AR-M550 (serv.man15) Service Manual ▷ View online
AR-M550/M620 SIMULATION 8 - 93
Operation/Procedure
1) Select YES/NO of data transfer.
2) Press [START] key.
Operation/Procedure
1) Enter the number corresponding to the information (item) to be
printed with 10-key.
2) Press [START] key.
Operation/Procedure
1) Enter the number corresponding to the volume with 10-key.
2) Press [START] key.
Selection of 1, 2, and 3 can be made during execution.
66-20
Purpose
Data transfer
Function
(Purpose)
(Purpose)
Used to read the back-up data by SIM 66-19 to the
SRAM. (Only when FAX is installed)
SRAM. (Only when FAX is installed)
Section
FAX
Item
Data
1
YES
Backup is executed.
2
NO
Backup is not executed.
66-21
Purpose
Adjustment/Setup/Operation data output/Check
(Display/Print)
(Display/Print)
Function
(Purpose)
(Purpose)
Used to print information related to FAX (various
registrations, communication management, file
management, system error protocol). (Only when FAX
is installed)
registrations, communication management, file
management, system error protocol). (Only when FAX
is installed)
Section
FAX
Item
Data
1
REGISTERED
Various registration information
2
MANAGEMENT
Communication management
information
information
3
FILE MANAGEMENT
File management information
4
SYSTEM ERROR
System error information
5
PROTOCOL
Protocol information
SIMULATION 66-19
ADDRESS DATA BACK UP. (WRITE TO FLASH ROM)
ARE YOU SURE?
1. YES
2. NO
SIMULATION 66-19
ADDRESS DATA BACK UP. (WRITE TO FLASH ROM) EXECUTING...
1
1
Press [START] key.
After completion of backup
SIMULATION 66-20
ADDRESS DATA BACK UP. (READ FROM FLASH ROM)
ARE YOU SURE?
1. YES
2. NO
SIMULATION 66-20
ADDRESS DATA BACK UP. (READ FROM FLASH ROM) EXECUTING...
1
1
Press [START] key.
After completion of read
66-22
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to adjust the handset volume. (Only when the
FAX is installed.)
FAX is installed.)
Section
FAX
Item
Operation
1
MIN
Small
2
MIDDLE
Medium
3
MAX
Large
Same display
Select 3 and press [START] key.
SIMULATION 66-21
FAX INFORMATION PRINT OUT. SELECT 1-5, AND PRESS START.
1. REGISTERED 2. MANAGEMENT
3. FILE MANAGEMENT 4. SYSTEM ERROR
5. PROTOCOL
(When 1)
SIMULATION 66-21
FAX INFORMATION PRINT OUT. EXECUTING···
1. REGISTERED
If there is no print data,
the display returns to the
original state without printing.
the display returns to the
original state without printing.
Select other than 0 and
press [START] key.
press [START] key.
After completion of backup
SIMULATION 66-22
HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.
1. MIN
2. MIDDLE
3. MAX
2
SIMULATION 66-22
HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.
EXECUTING···.
1. MIN
2. MIDDLE
3. MAX
2
Press [CUSTOM SETTINGS] key.
Press [START] key.
SIMULATION 66-22
HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.
EXECUTING···.
1. MIN
2. MIDDLE
3. MAX
3
SIMULATION 66-22
HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.
1. MIN
2. MIDDLE
3. MAX
3
Press [CUSTOM SETTINGS] key.
AR-M550/M620 SIMULATION 8 - 94
Operation/Procedure
1) Turn OFF the power.
2) Remove the protect pin.
3) Turn ON the power.
4) Enter the SIM 66-23 mode.
5) Press [START] key.
During operation, "EXECUTING" is displayed. When the operation is
completed normally, "COMPLETE" is displayed.
completed normally, "COMPLETE" is displayed.
If an error occurs, "FAIL" is displayed.
6) Turn OFF the power, and attach the protect pin.
Operation/Procedure
1) Select YES/NO of data clear.
2) Press [START] key.
Operation/Procedure
1) Enter the Modem dial-in FAX number (1 - 9, 0, *, #) with 10-key.
2) Press [START] key.
Operation/Procedure
1) Enter the Modem dial-in FAX number (1 - 9, 0, *, #) with 10-key.
2) Press [START] key.
Operation/Procedure
1) Enter the voice warp transfer number (1 - 9, 0, *, #) with 10-key.
2) Press [START] key.
66-23
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to download the FAX program. (Only when FAX
is installed)
Not used in the market. (For development)
is installed)
Not used in the market. (For development)
Section
FAX
Item
Press [START] key.
After failing of writing
66-24
Purpose
Clear
Function
(Purpose)
(Purpose)
Used to clear the FAST memory data. (Only when FAX
is installed)
is installed)
Section
FAX
Item
Data
1
YES
FAST memory data is cleared.
2
NO
Not cleared.
SIMULATION 66-23
FAX PROGRAM DOWNLOAD.
EJECT PROTECT PIN, AND PRESS START.
SIMULATION 66-23
FAX PROGRAM DOWNLOAD. EXECUTING···
SIMULATION 66-23
FAX PROGRAM DOWNLOAD.
COMPLETE
POWER OFF, AND SET PROTECT PIN
After completion of writing
SIMULATION 66-23
FAX PROGRAM DOWNLOAD.
FAIL
CHECK PROTECT PIN
66-25
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to register the FAX number for Modem dial-in.
(Only when FAX is installed)
Not used in the market. (For development)
(Only when FAX is installed)
Not used in the market. (For development)
Section
FAX
Item
Data
66-26
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to register external telephone numbers for
Modem dial-in. (Only when FAX is installed)
Not used in the market. (For development)
Modem dial-in. (Only when FAX is installed)
Not used in the market. (For development)
Section
FAX
Item
Data
66-27
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to register the transfer number for voice warp.
(Only when FAX is installed)
Not used in the market. (For development)
(Only when FAX is installed)
Not used in the market. (For development)
Section
FAX
Item
Data
SIMULATION 66-24
FAST MEMORY DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
SIMULATION 66-25
M-D-IN FAX NUMBER SETTING. 0-9:[0-9],*:[*],#:[#]
INPUT NUMBER AND PRESS START.
0123456789*#01234567
SIMULATION 66-26
M-D-IN EXTEL NUMBER SETTING. 0-9:[0-9],*:[*],#:[#]
INPUT NUMBER AND PRESS START.
0123456789*#01234567
SIMULATION 66-27
V-WP TRANSMIT NUMBER SETTING. 0-9:[0-9],*:[*],#:[#]
INPUT NUMBER AND PRESS START.
0123456789*#01234567
AR-M550/M620 SIMULATION 8 - 95
Operation/Procedure
1) Enter the number corresponding to the registration number with
10-key.
2) Use the handset to record a voice message. (Max. 6sec)
3) Onhook the handset. (End)
There are following five kinds of recording.
When [CUSTOMSETTING] key is pressed, recording is interrupted.
Operation/Procedure
1) Select YES/NO of data clear.
2) Press [START] key.
Operation/Procedure
The TEL/LIU state is displayed.
When the state is changed, it is highlighted.
Operation/Procedure
1) Enter the number corresponding to the check item with 10-key.
2) Press [START] key.
66-28
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to record voice messages. (Only when FAX is
installed.)
installed.)
Section
FAX
Item
Data
1
MESSAGE1
Recording No. 1
2
MESSAGE2
Recording No. 2
3
MESSAGE3
Recording No. 3
4
MESSAGE4
Recording No. 4
5
MESSAGE5
Recording No. 5
SIMULATION 66-28
VOICE RECORD. SELECT 1-5, AND PRESS START.
1.MESSAGE1 2.MESSAGE2 3.MESSAGE3
4.MESSAGE4 5.MESSAGE5
1
SIMULATION 66-28
VOICE RECORD.
PICKUP HANDSET.
1
SIMULATION 66-28
VOICE RECORD.
VOICE RECORDING...
1
SIMULATION 66-28
VOICE RECORD.
VOICE DATA TRANS...
1
Select 1 and press [START] key.
Press
[CUSTOM
SETTINGS] key.
[CUSTOM
SETTINGS] key.
Handset offhook
Completion of recording
6sec passed or handset onhook
66-29
Purpose
Clear
Function
(Purpose)
(Purpose)
Used to clear data related to an address book (one-
touch registration, program registration/expansion,
relay memory box registration, each table content).
touch registration, program registration/expansion,
relay memory box registration, each table content).
Section
FAX, Network scanner
Item
Data
1
YES
Address book data is cleared.
2
NO
Not cleared.
66-30
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the change in the TEL/LIU status.
Section
FAX
Item
Operation
HS1
Polarity reverse signal
HS2
Polarity reverse signal
RHS
Handset hook SW
EXHS
External telephone hook SW
66-31
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the relay operation.
Section
FAX
Item
Operation
SIMULATION 66-29
ADDRESS DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
1
SIMULATION 66-30
TEL/LIU SENSOR CHECK.
HS1 HS2
RHS
EXHS
1 0 0 0 1 1 0 0
1 2 3 4 5 6 7 8
SIMULATION 66-31
TEL/LIU SETTING.
INPUT 0-1, AND PRESS START.
1.
MPXA
2. CION 3. MR 4. EC
5.
S.
6.
CML
7. DP 8.
AR-M550/M620 SIMULATION 8 - 96
Operation/Procedure
When check is completed normally, "OK" is displayed. In case of an
error, "NG" is displayed.
error, "NG" is displayed.
(Display message)
Operation/Procedure
The detected signal is highlighted.
Operation/Procedure
Communication test is performed to measure the time (ms).
Send is made under the following conditions.
Operation/Procedure
1) Select YES/NO of Modem program reload.
2) Press [START] key.
When reload is completed normally, "OK" is displayed. In case of an
error, "CHECK SUM" is displayed.
error, "CHECK SUM" is displayed.
The result of Modem reload is displayed.
Operation/Procedure
1) Enter the number corresponding to the check mode with 10-key.
2) Press [START] key.
When check is completed normally, "OK" is displayed. Incase of an
error, "NG" is displayed.
error, "NG" is displayed.
When check is "repeat," the operation is continued until the result is
NG or [CUSTOM SETTINGS] key is pressed.
NG or [CUSTOM SETTINGS] key is pressed.
66-32
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the receive data (fixed data) from the
line.
line.
Section
FAX
Item
Operation
CHECKING
Checking
OK
Checking completed (OK)
NG
Checking completed (NG)
66-33
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the signal (BUSY TONE/CNG/CED/
FNET/DTMF) detection.
FNET/DTMF) detection.
Section
FAX
Item
Operation
66-34
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to measure the communication time of test
image data.
image data.
Section
FAX
Item
Operation
Communication means
Memory send
Image quality
Normal text
Density
Light
ECM
ON
Sender record
OFF
SIMULATION 66-32
RECEIVED DATA CHECK.
CHECKING···.(OK or NG)
SIMULATION 66-33
SIGNAL DETECT CHECK.
BUSY TONE
CNG
CED FNET DTMF
SIMULATION 66-34
COMMUNICATION TIME DISPLAY.
* * * * * ms
66-35
Purpose
Setting
Function
(Purpose)
(Purpose)
Modem program reloading (Only when FAX is
installed)
Not used in the market. (For development)
installed)
Not used in the market. (For development)
Section
FAX
Item
Data
1
YES
Modem block reload is cleared.
2
NO
Not reloaded.
COMPLETE
Reload completed
81
Check sum error
82
Write error
83
Delete error
84
Verify error
NG
Due to loader NG
Press [START] key.
After completion of reloading
66-36
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check interface between MFPC controller and
MDMC. (Check of the data line or the command line)
MDMC. (Check of the data line or the command line)
Section
FAX
Item
Operation
1
MFPC
←
MDMC
Date line once only
2
MFPC
→
MDMC
Date line once only
3
MFPC
←
MDMC
Data line repeat
4
MFPC
→
MDMC
Data line repeat
5
MFPC
←
MDMC
Command line once only
6
MFPC
→
MDMC
Command line once only
7
MFPC
←
MDMC
Command line repeat
8
MFPC
→
MDMC
Command line repeat
SIMULATION 66-35
MODEM PROGRAM RELOAD.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 66-35
MODEM PROGRAM RELOAD.
EXECITOMG···
LOADER··· xxxxx
MODEM···· xxxxx
SIMULATION 66-35
MODEM PROGRAM RELOAD.
LOADER···OK
MODEM····COMPLETE
Click on the first or last page to see other AR-M550 (serv.man15) service manuals if exist.