DOWNLOAD Sharp AR-M550 (serv.man15) Service Manual ↓ Size: 905.4 KB | Pages: 98 in PDF or view online for FREE

AR-M550/M620  SIMULATION  8 - 73

4) Press [START] key.

NOTE: When [P] key is pressed after entering the adjustment value in

this simulation, the adjustment value is set. When [START] key
is pressed, the adjustment value is set and copying is per-
formed.

(Select the scan mode to be adjusted.)

1) Enter the number corresponding to the scan mode to be adjusted

with 10-key.  (Select one of 3 - 5.)

2) Press [START] key.

(Scan off-center position adjustment)

1) Enter the scan image position adjustment value with 10-key.

2) Press [P] key or [START] key. 

When [START] key is pressed, the adjustment value is set and
copying is performed. 

Check the off-center of the printed image. 

Repeat the above procedures until a satisfactory result is obtained. 

(UNIT: 0.1mm/step  When the adjustment value is increased, the print
image is shifted to the front direction.)

(Copy condition setting in this simulation)

∗

To select paper (paper feed tray), perform the following procedures.

1) Enter 0 with 10-key. 

2) Press [START] key. (The mode is changed to the paper feed tray

selection mode.)

3) Enter the number corresponding to the paper feed tray to be used

with 10-key. (Select one of 1 - 6)

4) Press [START] key. (The paper feed tray is selected.)

When the total of the above set value and 10 is entered, the mode is
changed to the duplex print mode.

∗

To set the copy magnification ratio, perform the following procedure.

1) Enter 2 with 10-key.

2) Press [START] key. 

3) Enter the copy magnification ratio with 10-key.

4) Press [START] key.

NOTE: When [P] key is pressed after entering the adjustment value in

this simulation, the adjustment value is set. When [START] key
is pressed, the adjustment value is set and copying is per-
formed.

Set range

25 - 400 (%)

Select 0, and 
press [START] key.

Press [START] key, or 
press [CUSTOM SETTINGS] key.

50-12

Adjustment

Used to adjust the scan image off-center position. 
(Adjusted separately for each scan mode.)

Picture quality

Image position

Item

Set range

Default

0 TRAY SELECT

Paper feed tray 
selection

1 - 5

–

1 COPY START

Copy START (Default)

–

–

2 MAGNIFICATION Print magnification ratio

25 - 400%

100

(Resist adjustment value)

3 PLATEN

OC mode adjustment

0 - 99

50

4 SPF SIDE1

SPF front surface 
adjustment

5 SPF SIDE2

SPF back surface 
adjustment

50

2

Select 1, 
and press 
[START] key. 

Select other than 0 - 2, and 
press [START] key.

Press [CUSTOM SETTINGS] key. 

Press [START] key. 

Press [CUSTOM SETTINGS] key, 
or terminate copying.

SIMULATION 50-10

PRINT OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS

START.

0.TRAY SELECT 

1

   1.COPY START

2.MAGNIFICATION 

100

(ADJUSTMENT DATA)

3.TRAY1 

50

 4.TRAY2 

50

 5.TRAY3 

50

6.TRAY4 

50

 7.BPT  

50

  8.LCC   

50

 9. ADU   

50

SIMULATION 50-10

PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.

SIMULATION 50-10

PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND

PRESS START.

2.TRAY1

1

SIMULATION 50-10

PRINT OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS

START.

(FEED TRAY)

   1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

   5.BPT   6.LCC

   (ABOVE+10: DUPLEX MODE)

Normal display

NOW COPYING.

ERROR display

Door open

DOOR OPEN.

Jam

JAM

Paper empty

PAPER EMPTY.

1

TRAY1

TRAY1

2

TRAY2

TRAY2

3

TRAY3

TRAY3

4

TRAY4

TRAY4

5

BPT

Manual feed

6

LCC

Side LCC

Set range

25 - 400 (%)

AR-M550/M620  SIMULATION  8 - 74

(Select the scan mode to be adjusted.)

1) Enter the number corresponding to the adjustment item with 10-

key. 

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key.

(Shift for the adjustment value change: 1.0mm/step)

(Select the scan mode to be adjusted.)

1) Enter the number corresponding to the paper feed tray to be

adjusted with 10-key.  (Select one of 2 - 12.)

Select 2, and 
press [START] key.

Press [START] key, or 
press [CUSTOM SETTINGS] key.

50-27

Adjustment

Used to adjust the image loss of the scan image in the 
FAX/scan mode.

Picture quality

Item

Set range

Default

FAX send

1

OC (LEAD_EDGE)

OC lead edge

0 - 10

(Unit 1mm)

3 

(3mm)

2

OC (FRONT/REAR)

OC side

3

OC (TRAIL_EDGE)

OC rear edge

4

SPF (LEAD_EDGE)

SPF lead edge

5

SPF (FRONT/REAR) SPF side

6

SPF (TRAIL_EDGE)

SPF rear edge

7

CIS (LEAD_EDGE)

CIS lead edge

8

CIS (FRONT/REAR)

CIS side

9

CIS (TRAIL_EDGE)

CIS rear edge

50

1

2

Select 1, 
and press 
[START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key, 
or terminate copying.

Select 0, and press [START] key.

Press [START] key or 
press [CUSTOM SETTINGS] key.

SIMULATION 50-12

ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS

START.

0.TRAY SELECT 

1

   1.COPY START

2.MAGNIFICATION 

100

(ADJUSTMENT DATA)

3.PLATEN 

50

 4.SPF SIDE1 

50

 5.SPF SIDE2 

50

SIMULATION 50-12

ORIGINAL OFF-CENTER ADJUSTMENT. NOW COPYING.

SIMULATION 50-12

ORIGINAL OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND

PRESS START.

3.PLATEN

SIMULATION 50-12

ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS

START.

(FEED TRAY)

   1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

   5.BPT   6.LCC

   (ABOVE+10: DUPLEX MODE)

Select other than 0 - 2, and press [START] key.

100

SIMULATION 50-12

ORIGINAL OFF-CENTER ADJUSTMENT.

(MAGNIFICATION)

  INPUT 25-400(%)

Scanner mode

10

OC (LEAD_EDGE)

OC lead edge

0 - 10

(Unit 1mm)

0 

(0mm)

11

OC (FRONT/REAR)

OC side

12

OC (TRAIL_EDGE)

OC rear edge

13

SPF (LEAD_EDGE)

SPF lead edge

14

SPF (FRONT/REAR) SPF side

15

SPF (TRAIL_EDGE)

SPF rear edge

16

CIS (LEAD_EDGE)

CIS lead edge

17

CIS (FRONT/REAR)

CIS side

18

CIS (TRAIL_EDGE)

CIS rear edge

Press [START] key.

Press [CUSTOM SETTINGS] key.

51-2

Adjustment

Used to adjust the contact pressure of paper on the 
resist roller of each section (each paper feed, duplex 
feed and SPF paper feed of the copier). (This 
adjustment is required when the print image position 
variations are considerably great or when paper jams 
occur frequently.)

Paper transport (Discharge/Switchback/Transport)

Operation

Item

Set 

range

Default

0

TRAY SELECT

Paper feed tray selection 
(1 - 5)

–

–

1

PRINT START

Print start (Default)

–

–

2

TRAY1

Tray 1 adjustment value

0 - 99

46

3

TRAY2

Tray 2 adjustment value

4

TRAY3

Tray 3 adjustment value

5

TRAY4

Tray 4 adjustment value

6

BPT

Manual feed tray resist 
adjustment value

45

7

LCC

Side LCC resist adjustment 
value

8

ADU

ADU resist adjustment value

–

43

9

SPF (TOP)

SPF resist adjustment value 
(Top speed)

–

–

Item

Set range

Default

1

SIMULATION 50-27

ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND

PRESS START.

[FAX]

1.OC(LEAD_EDGE)  

0 

2.OC(FRONT/REAR)  

0 

3.OC(TRAIL_EDGE)  

0

4.SPF(LEAD_EDGE) 

0 

5.SPF(FRONT/REAR) 

0 

6.SPF(TRAIL_EDGE) 

0

7.CIS(LEAD_EDGE) 

0 

8.CIS(FRONT/REAR) 

0

 9.CIS(TRAIL_EDGE) 

0

[SCN]

10.OC(LEAD_EDGE)  

0 

11.OC(FRONT/REAR)  

0

 12.OC(TRAIL_EDGE)  

0

13.SPF(LEAD_EDGE) 

0 

14.SPF(FRONT/REAR) 

0

 15.SPF(TRAIL_EDGE) 

0

16.CIS(LEAD_EDGE) 

0 

17.CIS(FRONT/REAR) 

0

 18.CIS(TRAIL_EDGE) 

0

0

SIMULATION 50-27

ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND

PRESS START.

1.OC(LEAD_EDGE)

AR-M550/M620  SIMULATION  8 - 75

2) Press [START] key.

(Resist adjustment)

1) Enter the resist adjustment value with 10-key.

2) Press [START] key. 

When [START] key is pressed, the adjustment value is set and
paper feed and copying are performed.

(Copy condition setting in this simulation)

∗

To select paper (paper feed tray), perform the following procedures.

1) Enter 0 with 10-key. 

2) Press [START] key. (The mode is changed to the paper feed tray

selection mode.)

3) Enter the number corresponding to the paper feed tray to be used

with 10-key. 

4) Press [START] key. (The paper feed tray is selected.)

When the total of the above set value (1 - 6) and 10 is entered, the
mode is changed to the duplex print mode.

NOTE: When [P] key is pressed after entering the adjustment value in

this simulation, the adjustment value is set. When [START] key
is pressed, the adjustment value is set and copying is per-
formed.

1) Set the SPF paper feed guide to the max. position.

2) Select "MAX. POSITION" with 10-key. 

3) Press [START] key. 

The max. width detection level is recognized.

4) Press [CSUTOM SETTING] key. 

5) Set the SPF paper feed guide to A4R size position.

6) Select POSITION 1 with 10-key. 

7) Press [START] key.

The A4R width detection level is recognized.

8) Press [CSUTOM SETTING] key. 

9) Set the SPF paper feed guide to A5 size position.

10)  Select POSITION 2 with 10-key. 

11)  Press [START] key.

The A5 width detection level is recognized.

12) Press [CSUTOM SETTING] key.

13) Set the SPF paper feed guide to the min. position.

14) Select "MIN. POSITION" with 10-key. 

15) Press [START] key. 

The min. width detection level is recognized.

If the above procedures are not completed normally, ERROR is dis-
played. When completed normally, COMPLETE is displayed.

10 SPF (HIGH)

SPF resist adjustment value 
(High speed)

0 - 99

50

11 SPF (LOW)

SPF resist adjustment value 
(Low speed)

12 SPF FEED 

(TOP)

SPF paper fed resist 
adjustment value (Top speed)

–

–

13 SPF FEED 

(HIGH)

SPF paper feed resist 
adjustment value (High 
speed)

–

–

14 SPF FEED 

(LOW)

SPF paper feed resist 
adjustment (Low speed)

–

–

Normal display

NOW PRINTING.

ERROR display

Door open

DOOR OPEN.

Jam

JAM

Paper empty

PAPER EMPTY.

1

TRAY1

TRAY1

2

TRAY2

TRAY2

3

TRAY3

TRAY3

4

TRAY4

TRAY4

5

BPT

Manual feed

6

LCC

LCC

Item

Set 

range

Default

Select 0, and 
press [START] key.

Press [START] key, or 
press [CUSTOM SETTINGS] key.

53-6

Adjustment

Used to adjust the DSPF width detection level.

Operation

50

1

SIMULATION 51-2

RESIST TIMING ADJUSTMENT. SELECT 0-14, AND PRESS START.

0.TRAY SELECT 

1

   1.PRINT START

2.TRAY1 

50

 3.TRAY2 

50

 4.TRAY3 

50

5.TRAY4 

50

 6.BPT 

50

   7.LCC 

50

8.ADU   

50

 9.SPF(TOP) 

50

 10.SPF(HIGH) 

50

11.SPF(LOW) 

50

        12.SPF FEED(TOP) 

50

13.SPF FEED(HIGH) 

50

  14.SPF FEED(LOW) 

50

SIMULATION 51-2

RESIST TIMING ADJUSTMENT. NOW PRINTING.

SIMULATION 51-2

RESIST TIMING ADJUSTMENT. INPUT VALUE 0-99, AND PRESS

START.

1.TRAY1

Select 1, 
and press
 [START] key.

Select other than 0 - 1, and 
press [START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key, 
or terminate copying.

1

SIMULATION 51-2

RESIST TIMING ADJUSTMENT. SELECT 1-15, AND PRESS START.

(FEED TRAY)

   1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

   5.BPT   6.LCC

   (ABOVE+10: DUPLEX MODE)

AR-M550/M620  SIMULATION  8 - 76

1) Enter the number corresponding to the set item with 10-key.

2) Press [START] key. 

3) Enter the set value with 10key.

4) Press [START] key.

1) Select 2 with 10-key.

2) Press [START] key. 

3) Enter the adjustment value with 10key. (1 count: 0.1mm)

4) Press [START] key.

This simulation is used to change and check the engine soft SW. Set
this setting to the default.

There is no need to change this setting in the market.

Select 4, and press [START] key.

Press [CUSTOM SETTINGS] 
key.

53-7

Adjustment/Setup/Operation data output/Check 
(Display/Print)

Used to enter the SPF width detection adjustment 
value.

DSPF

Operation

Item

Set range

Default

1

MAX. POSITION

Max. width

0 - 1023

66

2

POSITION 1

Adjustment position 1

456

3

POSITION 2

Adjustment position 2

713

4

MIN. POSITION

Min. width

791

Press [START] key.

Press [CUSTOM SETTINGS] key.

1

Select 2, and press [START] key.

Select 3, and press [START] key.

Press [CUSTOM SETTINGS] key.

Press [CUSTOM SETTINGS] key.

Press [CUSTOM SETTINGS] key.

SIMULATION 53-6

SPF TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START.

1.MAX.POSITION

2.POSITION 1

3.POSITION 2

4.MIN.POSITION

SIMULATION 53-6

SPF TRAY ADJUSTMENT.

MAX.POSITION ... COMPLETE (or “ERROR”)

SIMULATION 53-6

SPF TRAY ADJUSTMENT.

POSITION 1 ... COMPLETE (or “ERROR”)

SIMULATION 53-6

SPF TRAY ADJUSTMENT.

POSITION 2 ... COMPLETE (or “ERROR”)

Select 1, and 
press [START] key.

SIMULATION 53-6

SPF TRAY ADJUSTMENT.

MIN.POSITION ... COMPLETE (or “ERROR”)

1

SIMULATION 53-7

SPF TRAY ADJUSTMENT(MANUAL). SELECT 1-4, AND PRESS

START.

1.MAX.POSITION:   

66

2.POSITION 1  :  

456

3.POSITION 2  :  

713

4.MIN.POSITION:  

791

66

SIMULATION 53-7

SPF TRAY ADJUSTMENT(MANUAL). INPUT VALUE 0-1023, AND

PRESS START.

1.MAX.POSITION

53-8

Adjustment

Used to adjust the document scan start position. (Used 
to adjust the scanner scan position in the SPF mode 
front scan.)

Item

Set 

range

Default

2

MANUAL

Manual feed adjustment (Direct 
entry of a number)

1 - 60

32

Select 2, and 
press [START] key. 

Press [START] key, or 
press [CUSTOM SETTINGS] key.

55-1

Setting

Used to set the specifications of the engine control 
operations. (PCU PWB)

Operation Specifications

Press [START] key.

Press [CUSTOM SETTINGS] key or [START] key.

SIMULATION 53-8

SPF SCANNING POSITION ADJUSTMENT. PRESS START.

2.MANUAL   

25

25

SIMULATION 53-8

SPF SCANNING POSITION ADJUSTMENT. INPUT VALUE 1-35, AND

PRESS START.

2.MANUAL

1

SIMULATION 55-1

ENGINNE SOFT SW. SETTING. SELECT 1-16, AND PRESS START.

1 2 3 4 5 6 7 8

0 0 0 0 1 0 0 1

SIMULATION 55-1

ENGINNE SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS

START.

    SOFT SW-1: