DOWNLOAD Sharp AR-M35 / AR-M450 (serv.man32) Service Manual ↓ Size: 883.86 KB | Pages: 38 in PDF or view online for FREE

Originals set in the automatic document feeder will be automatically fed and copied sequentially.

The automatic document feeder will simultaneously scan both sides of originals when two-sided to one-sided or two-
sided to two-sided copying is being done.

A stack of up to 50 original sheets (30 original sheets*

1 

for 8-1/2" x 14" (B4) or larger)  of the same size paper can be

set in the document feeder tray provided the stack height is within the limit shown below.
A stack of up to 30 mixed size originals can be set if the width of the originals is the same and the stack height is within
the limit shown below. In this case, however, stapling and duplex will not function and some special functions may not
give the expected result.
*1 For paper heavier than 28 lbs. (105 

g

/m

2

), only a stack of up to 15 sheets can be set. Setting 16 or more sheets may

cause incorrect scanning of original and scanned image may become expanded compared with original itself.

●

Use originals within the specified size and weight ranges. Use of originals out of the specified range may cause
an original misfeed.

●

Before loading originals into the document feeder tray, be sure to remove any staples or paper clips.

●

If originals have damp spots from correction fluid, ink or glue from pasteups, be sure they are dried before they
are fed. If not, the interior of the document feeder or the document glass may be soiled.

●

To prevent incorrect original size detection, original misfeeds or smudges on copies, use the following as a guide
for feeding originals.

Transparency film, tracing paper, carbon paper, thermal paper or originals printed with thermal transfer ink
ribbon should not be fed through the document feeder. Originals to be fed through the feeder should not be
damaged, crumpled or folded or have loosely pasted paper on them or cutouts in them. Originals with multiple
punched holes other than two-hole or three-hole punched paper may not feed correctly.

●

When using originals with two or three holes, place them so that the punched edge is at a position other than the
feed slot.

■

■

■

■

■

■

■

■

■

■

14 lbs. or 

50

g

/m

2

2

2

34 lbs. or 

128

g

/m

2

Original size: 

(148 x 210 mm) 

5-1/2" x 8-1/2"

or A5

11" x 17"

or A3

(297 x 420 mm)

Weight (thickness):

g

/m  

... Weight of a sheet of paper of 1 m

3/16" or 5.0 mm 
or less

1/4" or 6.5 mm 
or less

Total aggregate thickness must not exceed 1/4" or 
6.5 mm (for 14 to 21 lbs. or 50 to 80 

g

/m

2

 paper).

Total aggregate thickness must not exceed 3/16" or 
5.0 mm (for 21 to 34 lbs. or 80 to 128 

g

/m

2

 paper).

Hole positions

Hole positions

Hole 
positions

■

■

■

■

■

Original size detector

NOTE
Do not place any objects under the original size
detector, because they may damage it or the original
size may not be detected properly.

●

Set an original by aligning its corner with the tip of the
scale ( ) mark at the left rear corner of the glass as
shown in the illustrations.

■

■

■

■

■

Set the originals all the way
into the feed slot. Do not
exceed the maximum
height line marked on the
original guide.

or B4

Original scale

mark

Original scale

mark

8

1

2

/ x

11 or A4

8

1

2

/ x

11R or A4R

8

1

2

/ x

14

11x17 or A3

or B4

5

1

2

/

8

1

2

/

x

or A5

■

■

■

■

■

Descriptions of functions that follow in this manual assume that originals are oriented as shown.

Document feeder tray

Document glass

■

■

■

■

■

If the orientation of the originals and copy paper are different, the original image will be automatically rotated 90°
and copied. (When an image is rotated, a message will be displayed.) When enlargement of originals larger than 8-
1/2" x 11" or A4 is selected, rotation cannot be done.

●

Orientation of original

Orientation of paper

Copy after rotation

Face down

Face down

Place originals in the document feeder tray or on
the document glass so that the top of the original
is positioned to the rear side of the machine. If
not, staples will be incorrectly positioned and
some special features may not give the expected
result.

Top

Top

Top

Bottom

Bottom

Bottom

Top

Bottom

This section describes the normal copying procedure.

■

■

■

■

■

A4

A4

A3

A4

A4R

2.
3.
4.

ORIGINAL

The one-sided to one-
sided mode is selected
when no icon for a two-
sided mode appears in the
dashed area on the display.
If the 1-sided to 1-sided
copy mode is already
selected, steps 3 to 5 are
not needed.

2-SIDED COPY

OUTPUT

The [1-sided to 1-sided] key
will be highlighted.

OK

Ensure that paper of the same size as the
originals is automatically selected. (

✼

Note)

COPY RATIO

PAPER SELECT

The selected tray will be
highlighted or the message
“LOAD xxxxxx PAPER.” will
appear. If the message ap-
pears, load paper in a pa-
per tray or the bypass tray
with paper of the required
size. Even if the message
above is displayed, copy-
ing can be performed onto
the currently selected pa-
per.

(

✼

Note)  The following requirements must be satisfied.

●

Originals of a standard size (11" x 17", 8-1/2" x 14", 8-1/2"
x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2", A3, B4, A4, A4R or A5)
are set and the auto paper select function is enabled.

TRANSPA

A4

1

X

A3

2.

3.

PLAIN

PLAIN

If originals of a size other
than the sizes above are to
be copied, manually select
the desired paper size.

Original

Copy