DOWNLOAD Sharp AR-M316 (serv.man10) Service Manual ↓ Size: 14.14 MB | Pages: 127 in PDF or view online for FREE

AR-M256/M257/M258/M316/M317/M318/5625/5631  SIMULATION 8 - 47

With the RSPF or the OC cover open, put a black background chart on
the OC glass (the RSPF glass surface is included for the RSPF stan-
dard model), and press the [START] key. 

If the adjustment is executed normally, the adjustment value is dis-
played and saved in the EEPROM. If an error occurs, “ERR” is dis-
played and the value is not saved in the EEPROM.

If the adjustment is not performed because of abnormality, “---” is dis-
played. 

During execution of the adjustment, the operation cannot be inter-
rupted.

Used to enter the number of SW to be changed.

The bit to be changed is specified by 10-key. (The current value is high-
lighted.)

When [START] key is pressed, the entered value is set.

Press the [START] key, and the LSU test is performed.
Used to set the LSU to ON state and check that the sync signal
(HSYNC/) is outputted or not.
After operation for 30 sec, the result is displayed. (Interruption cannot
be made for 5 sec after starting the operation.)

Pressing the [START] key performs shading, and displays the result
(center pixel).

Lift the RSPF unit to the fully open position, and press the [START] key.
[ ] indicates the order number of the pixel of the white sheet for RSPF 
exposure correction in the RSPF position.
If the adjustment is normally completed, “COMPLETE” is displayed 
and data are written into the EEPROM.
In case of an abnormality, “ERROR” is displayed and no data is written 
into the EEPROM.
The RSPF white correction start pixel = Displayed pixel position – 34

53-8

Adjustment

Used to adjust the RSPF scan position of the mirror 
unit automatically. For the RSPF scan position 
automatic adjustment, the mirror unit is shifted to 
11mm before the RSPF glass cover edge, and is 
operated automatically to scan images by the unit of 1 
step, detecting the position up to the glass cover 
automatically.
(Adjustment value)
Default: 50, Adjustment range: 1 - 99
Adjustment unit: 1 = about 0.127mm

55-1

Setting

Used to set the soft switch.

Operation

 
 
 
 
 

SIMULATION 55-1 

61-1

Operation test/check

Used to check the LSU (polygon motor) operation.
Check speed can select 145mm/s or 122mm/s 
individually.

LSU

Operation

63-1

Adjustment/setting/operation data output/check 
(display/print)

Used to check the result of shading correction. 
(The shading correction data are displayed.)

Scanner (Exposure)

Operation

63-7

Adjustment

Used to adjust the RSPF white correction start pixel 
position automatically.
This adjustment is performed after the lens unit is 
replaced.

Scanner

Operation

 
 
 
 
 
 

SIMULATION 61-1 

AR-M256/M257/M258/M316/M317/M318/5625/5631  SIMULATION 8 - 48

If the simulation is executed with the RSPF unit closed, an error will 
result.

1.

Select the print item with the 10-key. 

2.

Press the [START] key.
The display is shifted to the copy menu. 

3.

Select the paper feed tray and the print density. 

4.

Press the [START] key.
Copying is started.

During execution of the print test, the [CUSTOM SETTINGS] key and
the [INTERRUPTION] key are invalid. 

* If the IMC board is not installed, the key inputs cannot be made.

Press the keys displayed on the LCD sequentially. 

Adjust the touch panel coordinates. 

When the point of “+” on the LCD is pressed, it turns gray. Press all the
four points of “+.”

Check the touch panel coordinates.

Press the keys displayed on the LCD sequentially.

When the touch panel is pressed, the X-coordinate and the Y-coordi-
nate (dot conversion values) are displayed.

Check the key input of the operation panel.
Press the keys displayed on the LCD sequentially.

After completion of all key entries, “COMPLETE” is displayed.

1.

Enter the soft SW number to be selected with the 10-key. 

2.

Check and change the setting content of the selected soft SW. 

3.

Press the [START] key to save the set content. 

The FAX-related soft SW is displayed on the LCD, and changing can
be made by monitoring it.

Note: Executable only when the FAX is installed.

64-1

Operation test/check

Used to check the operation of the printer function 
(auto print operation).

Printer

Operation

Item

Content

Setting 

range

Default

1

2 BY 4 
MODE

Self print is made in 2 by 4 mode 
(printing 2 lines and not printing 
4 lines). Since scanning is not 
performed, when the original is 
set on the RSPF, this cannot be 
performed. 
* Duplex print cannot be made.

1-2

1

2

LATTICE 
PRINT

Lattice print (1cm, 1dot width 
WLT, A3 print (A3 main scan, 
WLT sub scan)) is performed.
* Duplex print can be made. 

65-1

Adjustment

Used to adjust the touch panel (LCD display section) 
detection position.

Operation (Display, Operation)

65-2

Adjustment/Setting/Operation data output check 
(Display, Print)

Used to check the touch panel (LCD display section) 
detection position adjustment result. 

Operation (Display, Operation)

65-5

Adjustment/Setting/Operation data output check 
(Display, Print)

Used to check the key inputs of the operation panel.

Operation (screen/operation)

66-1

Setting

Used to change and check the FAX-related soft SW.

FAX

AR-M256/M257/M258/M316/M317/M318/5625/5631  SIMULATION 8 - 49

1.

Enter the country code with the 10-key, and press the [START] key. 

2.

When “1: (YES)” is selected, the soft SW corresponding to the
country code is cleared. When “2: (NO)” is selected, the simulation
is canceled.

Country code

The codes other than the above are accepted as Japan.

Note: Executable only when the FAX is installed.

Press the [START] key.

Read/write can be checked for FAX PWB memory.

The check result is displayed separately for each memory.

1.

Memory to be checked

2.

Detailed procedure

Interruption cannot be made during operation.

Note: Executable only when the FAX is installed.

Select the signal number with the 10-key, and press the [START] key.
The signal is sent to the line and the machine speaker. (Sending the
signal is continued until the [CUSTOM SETTINGS] key is pressed.)

By entering the signal number and pressing the [START] key during
execution, the signal kind can be changed.

66-2

Adjustment

Used to clear the FAX-related soft SW. 
(Except for the FAX adjustment values)

FAX

Japan

: 00000000

U.S.A.

: 10110101

Australia

: 00001001

U.K.

: 10110100

France

: 00111101

Germany

: 00000100

Sweden

: 10100101

New Zealand : 01111110

China

: 00100110

Singapore

: 10011100

Taiwan

: 11111110

India

: 01010011

Malaysia

: 01101100

Hong Kong

: 01010000

Middle east

: 11111101

SouthAfrica

: 10011111

Spain

: 10100000

Portugal

: 10001011

Russia

: 10111000

Denmark

: 00110001

Norway

: 10000010

Switzerland

: 10100110

Italy

: 01011001

Belgium

: 00001111

Luxembourg : 01101001

Netherlands : 01111011

Finland

: 00111100

 

1

 

0 0 0 0 1 0 0 1

1 2 3 4 5 6 7 8

66-3

Operation test/check

FAX PWB memory check

FAX

Operation

DRAM

SRAM

Flash ROM

Program area

SUM check only

Memory area

Option memory

The memory size follows the 
automatically detected value.

PAGE

MODEM

1

“55H” is written to all the addresses of each memory, and the 
address data are read in sequence to check that they were 
properly written.

2

“AAH” is written to all the addresses of each memory, and the 
address data are read in sequence to check that they were 
properly written.

3

“00H” is written to all the addresses of each memory, and the 
address data are read in sequence to check that they were 
properly written.

4

Perform checks 1 - 3 sequentially. If there is no abnormality, it is 
“OK.” If there is any abnormality, “NG” is notified to the error 
address.

5

The check result is saved. New result is overwrited with each 
check.

66-4

Operation test/check

Signal send mode (Signal send level: Max.)

FAX

Operation

Item

Send signal

Send level

Selection 

menu

1

NO SIGNAL Signal not sent

None

2

33.6 V34

–

–

3

31.2 V34

–

–

4

28.8 V34

–

–

1

AR-M256/M257/M258/M316/M317/M318/5625/5631  SIMULATION 8 - 50

Note: Executable only when the FAX is installed.

Select the signal number with the 10-key, and press the [START] key. 

By setting the signal number, signals are sent to the line and the
machine speaker. (Sending signals is continued until interruption com-
mand is made (by pressing [CUSTOM SETTINGS] key.)

By entering the signal number and pressing the [START] key during
execution, the signal kind can be changed.

Note: Executable only when the FAX is installed.

5

26.4 V34

–

–

6

24.0 V34

–

–

7

16.0 V34

–

–

8

19.2 V34

–

–

9

16.8 V34

–

–

10 14.4 V34

–

–

11 12.0 V34

–

–

12 9.6 V34

–

–

13 7.2 V34

–

–

14 4.8 V34

–

–

15 2.4 V34

–

–

16 14.4 V33

–

–

17 12.0 V33

–

–

18 14.4 V17

–

–

19 12.0 V17

–

–

20 9.6 V17

–

–

21 7.2 V17

–

–

22 9.6 V29

–

–

23 7.2 V29

–

–

24 4.8 V27t

–

–

25 2.4 V27t

–

–

26 0.3 FLG

7EH Flag signal

Yes

27 CED2100

Tone signal

Yes

28 CNG1100
29 0.3 V21

30 ANSam

31 RINGER

Pseudo-ringer sound
([ON HOOK] key ON)

None

32 No MSG

Voice message (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
sound composition IC volume to 0.

33 No RBT

Ring back tone (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
G/A volume to 0.

34 DP MAKE

Dial pulse (make)

1: 0dB
2: Soft SW

Maintain the make state with keeping 
the condition to be able to send to the 
dial pulse line.

35 DP BRK

Dial pulse (break)

1: 0dB
2: Soft SW

Maintain the break state with keeping 
the condition to be able to send to the 
dial pulse line.

Item

Send signal

Send level

Selection 

menu

 

1

66-5

Operation test/check

Signal send mode (Signal send level soft SW setting)

FAX

Operation

Signal number

Send signal

Send level

Selection 

menu

1 NO SIGNAL Signal not sent

None

2 33.6 V34

33.6 V34

–

3 31.2 V34

31.2 V34

–

4 28.8 V34

28.8 V34

–

5 26.4 V34

26.4 V34

–

6 24.0 V34

24.0 V34

–

7 16.0 V34

16.0 V34

–

8 19.2 V34

19.2 V34

–

9 16.8 V34

16.8 V34

–

10 14.4 V34

14.4 V34

–

11 12.0 V34

12.0 V34

–

12 9.6 V34

9.6 V34

–

13 7.2 V34

7.2 V34

–

14 4.8 V34

4.8 V34

–

15 2.4 V34

2.4 V34

–

16 14.4 V33

14.4 V33

–

17 12.0 V33

12.0 V33

–

18 14.4 V17

14.4 V17

–

19 12.0 V17

12.0 V17

–

20 9.6 V17

9.6 V17

–

21 7.2 V17

7.2 V17

–

22 9.6 V29

9.6 V29

–

23 7.2 V29

7.2 V29

–

24 4.8 V27t

4.8 V27t

–

25 2.4 V27t

2.4 V27t

–

26 0.3 FLG

7EH Flag signal

Yes

27 CED2100

Tone signal

Yes

28 CNG1100

29 0.3 V21

30 ANSam

31 RINGER

Pseudo-ringer sound
([ON HOOK] key ON)

None

32 No MSG

Voice message (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
sound composition IC volume to 0.

33 No RBT

Ring back tone (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
G/A volume to 0.

34 DP MAKE

Dial pulse (make)

1: 0dB
2: Soft SW

Maintain the make state with keeping 
the condition to be able to send to the 
dial pulse line.

35 DP BRK

Dial pulse (break)

1: 0dB
2: Soft SW

Maintain the break state with keeping 
the condition to be able to send to the 
dial pulse line.