Sharp AR-M316 (serv.man10) Service Manual ▷ View online
AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 27
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the PS expansion kit soft key with the 10-
key and press the [START] key, and the collating result is displayed
with OK or NG.
key and press the [START] key, and the collating result is displayed
with OK or NG.
After canceling the simulation, if OK, the PS expansion kit function is
enable; if NG, the PS expansion kit function is disabled.
enable; if NG, the PS expansion kit function is disabled.
This setting must be reset after the simulation cancel.
Note: Executable only when the PCL/PS3 is installed.
Operation/procedure
Input the set value with the 10-key and press the [START] key.
Note: Setup is allowed only for Japan and UK.
Operation/procedure
Select the display language (language code) with the 10-key according
to the table below, and press the [START] key.
to the table below, and press the [START] key.
This setup varies in connection with SIM 26-6 (Destination setup).
Operation/procedure
Input the set value with the 10-key and press the [START] key.
This setup varies in connection with SIM 26-6 (Destination setup).
Operation/procedure
Enter the set value with 10-key, and press [START] key.
26-14
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to input the Software Key for the PS extention kit.
Section
Printer
Item
Specifications
26-18
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set enable/disable of toner save operation.
Item
Specifications
Operation mode (Common)
Item
Content
Setting
range
Default
0
OFF
Disable
0-1
0
1
ON
Enable
26-22
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the specification (language display) for the
destination.
destination.
Item
Specifications
Item
Language
code
ASIC
expression
Remarks
0
JAPANESE
ja
6A 61
1
ENG.US
en
65 6E
2
ENG.UK
gb
67 62
3
FRENCH
fr
66 72
4
GERMAN
de
64 65
5
ITALY
it
69 74
6
DUTCH
nl
6E 6C
7
SWEDISH
sv
73 76
8
SPANISH
es
65 73
9
PORTUGUESE
pt
70 74
10 TURKISH
tr
74
72
11 GREEK
el
65 6C
12 POLISH
pl
70 6C
13 HUNGARIAN
hu
68 75
14 CZECH
cs
63 73
15 RUSSIAN
ru
72 75
16 FINNISH
fi
66 69
17 NORWEGIAN
no
6E 6F
18 DANISH
da
64 61
19 CHINESE
zh
7A 68
20 TAIWANESE
tw
74 77
Traditional Chinese
supported locally
supported locally
21 SLOVAK
sk
73 6B
22 HEBREW
he
68 65
Supported locally
23
BRAZILIAN
PORTUGUESE
PORTUGUESE
pb
70 62
24 ARABIC
ar
61 72
26-30
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set ON/OFF of the heater lamp slow-up control
conforming to the CE mark control.
conforming to the CE mark control.
Item
Specifications
Operation mode (Common)
Item
Default
Japan, SEC, SECL, SCA, SEF, Taiwan
Others
0
OFF
0
1
1
ON
26-35
Purpose
Setup
Function
(Purpose)
(Purpose)
Used to set whether the same continuous troubles are
displayed as one trouble or the series of troubles with
SIM 22-4 when the same troubles occur continuously.
displayed as one trouble or the series of troubles with
SIM 22-4 when the same troubles occur continuously.
Item
Specifications
Item
Content
Default
0
ONCE
When two or more troubles occur, only one is
registered.
registered.
0
1
ANY
All the troubles occurred are registered.
Item
Language
code
ASIC
expression
Remarks
SIMULATION 26-22
AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 28
Operation/procedure
Input the set value with the 10-key and press the [START] key.
Note: Executable only with SRU (AR models).
Operation/procedure
Enter the set value with the 10-key, and press the [START] key.
Operation/procedure
When this setting is made, the image output direction in the staple
mode and that in the normal mode become the same. Therefore, the
user who uses printed paper (logo, house style, etc) need not change
the original direction in the staple mode. (When the finisher is used,
images are rotated 180 degrees in the staple mode.)
mode and that in the normal mode become the same. Therefore, the
user who uses printed paper (logo, house style, etc) need not change
the original direction in the staple mode. (When the finisher is used,
images are rotated 180 degrees in the staple mode.)
Enter the set value with the 10-key, and press the [START] key.
Note: Executable only when the finisher is installed.
Operation/procedure
Enter the set value with the 10-key, and press the [START] key.
Operation/procedure
Input the set value with the 10-key and press the [START] key.
• AR-M256/M257/M258/M316/M317/M318
• AR-5625/5631
26-36
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set whether the machine is stopped or not
when the maintenance counter life is expired.
when the maintenance counter life is expired.
Item
Operation
Item
Content
Default
0
STOP
Stop
1
1
NON STOP
Non stop
26-41
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set ON/OFF of the automatic magnification
ratio selection (AMS) when setting the binding function.
ratio selection (AMS) when setting the binding function.
Item
Operation
Item
Content
Default
0
OFF
AMS is not set automatically.
1 (SUK, SEF,
SEEG, SEEG2)
0 (Others)
1
ON
AMS is set automatically.
26-46
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set whether to meet with the output direction of
images regardless of the mode when installing the
finisher.
images regardless of the mode when installing the
finisher.
Item
Operation
Item
Content
Default
0
OFF
No setting (The output image direction is
changed in the staple mode of the finisher.)
changed in the staple mode of the finisher.)
0
1
ON
Setting (The output image direction is the
same regardless of stapling or not.)
same regardless of stapling or not.)
26-50
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set ON/OFF of the black and white reversion
function.
function.
Item
Operation
Item
Content
Default
0
ON
Enable
1 (SUK)
0 (Others)
1
OFF
Disable
26-57
Purpose
Setting
Function (Purpose)
Used to set the model code.
Item
Operation
Item
Default
1
AR-M256
1
2
AR-M257
3
AR-M258
4
AR-M317
5
AR-M316
6
AR-M318
7
AR-267FP
8
AR-317FP
9
AR-267FG
10
AR-317FG
11
AR-267S
12
AR-317G
13
AR-267G
14
AR-317S
Item
Default
1
AR-5625
1
2
AR-5631
SIMULATION 26-57
SIMULATION 26-57
AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 29
Operation/procedure
Input the set value with the 10-key and press the [START] key.
This setup varies in connection with SIM 26-6 (Destination setup).
Operation/procedure
Select the short time setup or the long time setup of the pre-heat time
and the auto power shut off time with the 10-key, and press the
[START] key.
and the auto power shut off time with the 10-key, and press the
[START] key.
Note: When the sub code 71 is entered to display the setting menu,the
default values are always displayed. (However,the default time is
not always set.)
not always set.)
Operation/procedure
Input the set value with the 10-key and press the [START] key.
Operation/procedure
Input the set value with the 10-key and press the [START] key.
Operation/procedure
1.
The currently set number is displayed on the PRESENT column.
2.
Enter the new tag number (Max. 8 digits) with the 10-key.
The entered number is displayed on the NEW column.
The entered number is displayed on the NEW column.
3.
Press the [START] key.
The set value is stored and “PRESENT” is revised.
The set value is stored and “PRESENT” is revised.
Operation/procedure
The active sensors and detectors are highlighted.
26-60
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set enable/disable of the FAX mode key when
FAX is not installed. (When FAX is installed, the FAX
mode is enabled regardless of this setup.)
FAX is not installed. (When FAX is installed, the FAX
mode is enabled regardless of this setup.)
Item
Operation
Item
Content
Default
JAPAN, SEC,
SECL, SUK, SCA
Others
0
ON
Effective (The message with
FAX uninstalled is displayed.)
FAX uninstalled is displayed.)
0
1
1
OFF
Disable (Error Beep)
26-71
Purpose
Setting
Function
(Purpose)
(Purpose)
In the power save time setting, the pre-heat (pre-heat
mode setting) and the auto power shut off time can be
set to the short time setup (pre-heat: 1 min, auto power
shut off: 4 min) and the long time setup (pre-heat:
5min, auto power shut off: 30min).
mode setting) and the auto power shut off time can be
set to the short time setup (pre-heat: 1 min, auto power
shut off: 4 min) and the long time setup (pre-heat:
5min, auto power shut off: 30min).
Item
Content
Default
1
Preheat: 1min, auto power shut off: 4min
2
2
Preheat: 5min, auto power shut off: 30min
26-72
Purpose
Setting
Function
(Purpose)
(Purpose)
The letterhead support is set.
When “Letterhead paper setting” is selected, the set
value of SIM 26-46 (Image output direction setting) is
set to “Setting Enable” accordingly.
When “Letterhead paper setting” is selected, the set
value of SIM 26-46 (Image output direction setting) is
set to “Setting Enable” accordingly.
Item
Content
Default
Item
0
OFF
Letterhead paper is not set.
0-1
0
1
ON
Letterhead paper is set.
SIMULATION 26-72
27
27-1
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set PC/MODEM communication trouble
(U7-00) detection Yes/No.
(U7-00) detection Yes/No.
Section
Communication (RIC/MODEM)
Item
Specifications
Operation mode (Common)
Item
Content
Default
0
OFF
In case of the communication trouble, U7-00 is
not displayed.
not displayed.
0
1
ON
In case of the communication trouble, U7-00 is
displayed.
displayed.
27-5
Purpose
Setting
Function (Purpose)
Used to set the tag number.
Item
Data
30
30-1
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to display the sensor status attached to the
machine.
machine.
Section
Others
Item
Operation
PPD1H
PS paper detection 1 sensor
PPD1L
PS paper detection 2 sensor
PPD2
Fusing paper sensor
POD1
1st paper exit paper out sensor
DVCH
Developing cartridge detection sensor
DRST
Drum intial detection sensor
DSWR1
Interlock switch (side door)
SFTHP
Shifter home position sensor
POD2
2nd paper exit paper out sensor
AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 30
Operation/procedure
The active sensors and detectors are highlighted.
Width detection size of the manual feed tray (one of them is displayed.)
A4/A3, LT/WLT, B5/B4, INV/LTR, A5/A4R, B5R, POSTCARD, EXTRA,
8K/16K
8K/16K
(At detection, highlighted)
Operation/procedure
The active sensors and detectors are highlighted.
Width detection size of the manual feed tray (one of them is displayed.)
A4/A3, LT/WLT, B5/B4, INV/LTR, A5/A4R, B5R, POSTCARD, EXTRA,
8K/16K
8K/16K
Operation/procedure
The adjustment method is of the 4-point system. Set the guide to Max.
(A3/WLetter) position, A4R/Letter R position, A5R/Invoice R position,
and Min. position for adjustment.
(A3/WLetter) position, A4R/Letter R position, A5R/Invoice R position,
and Min. position for adjustment.
1) Set A3/W Letter and fit the guide, then press the [START] key.
2) Set A4R/LetterR and fit the guide, then press the [START] key.
3) Set to A5R/INVOICE R and fit the guide, then press the [START] key.
4) Narrow the guide at minimum, press the [START] key.
5) Set the paper detection width (+), and press the [START] key.
6) Set the paper detection width (–), and press the [START] key.
If “FAILED” is displayed in procedure 1), 2), 3), or 4), it is NG of adjust-
ment. Repeat the adjustment.
ment. Repeat the adjustment.
Operation/procedure
The AD conversion value of manual feed width detection is displayed.
TOPF
2nd paper exit full detection sensor
DSWR0
2nd paper exit cover open/close detection sensor
LOEMP
1st paper exit empty detection sensor
DUP2
Reverse path paper sensor
30-2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to display the status of the sensors attached to
the standard cassette and the manual feed tray. (Use
SIM 4-2 for the option cassettes.)
The sensor of an uninstalled cassette is not displayed.
the standard cassette and the manual feed tray. (Use
SIM 4-2 for the option cassettes.)
The sensor of an uninstalled cassette is not displayed.
Section
Paper feed
Item
Operation
PED1
1st cassette paper empty sensor
LUD1
1st cassette paper upper limit detection sensor
CD1
1st cassette empty sensor
PED2
2nd cassette paper empty sensor
LUD2
2nd cassette paper upper limit detection sensor
CD2
2nd cassette empty sensor
PFD2
2nd cassette paper pass sensor
DSWR2
2nd cassette right door detection sensor
MPED
Manual tray paper empty detection
MPLS1
Manual tray length detection 1
MPLS2
Manual tray length detection 2
MPLD1
Manual feed paper length detection 1
MPLD2
Manual feed paper length detection 2
40
40-1
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the sensor of the machine manual feed
tray.
tray.
Section
Paper feed
Item
Operation
MPLS1
Manual tray length detection 1
MPLS2
Manual tray length detection 2
MPLD1
Manual feed paper length detection 1
MPLD2
Manual feed paper length detection 2
40-2
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the manual paper feed tray paper width
detector detection level.
detector detection level.
Section
Paper feed
Item
Operation
Middle position adjustment L
Yes
MID-L ADJ.ON
No
MID-L ADJ.OFF
Middle position adjustment S
Yes
NID-S ADJ.ON
No
MID-S ADJ.OFF
AB series
Inch series
40-3
Purpose
Adjustment
Function
(Purpose)
(Purpose)
The AD conversion value of manual feed width
detection is displayed.
detection is displayed.
Section
Paper feed
Item
Operation
Click on the first or last page to see other AR-M316 (serv.man10) service manuals if exist.