Sharp AR-FX12 (serv.man7) Service Manual ▷ View online
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-17
<List of set values>
<List of set values>
66-11
Purpose
Operation test, check
Function (Content)
Used to check the output operation of FAX G3
mode 300BPS.
(Used to check the MODEM operation.)
Send level Max.
(Only when FAX is installed.)
mode 300BPS.
(Used to check the MODEM operation.)
Send level Max.
(Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure A signal of 300bps is outputted. (Level Max.)
Enter a number during execution to change the
kind of signal.
Press START to start sending a voice message.
Press CUSTOM SETTINGS to terminate.
kind of signal.
Press START to start sending a voice message.
Press CUSTOM SETTINGS to terminate.
1
NO SIGNAL
No signal
2
11111
3
11110
4
00000
5
010101
6
00001
SIMULATION 66-11
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111
3.11110
4.00000
5.010101
6.00001
1
SIMULATION 66-11
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111
3.11110
4.00000
5.010101
6.00001
1
SIMULATION 66-11
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111
3.11110
4.00000
5.010101
6.00001
3
Press [CUSTOM SETTINGS] key.
Select 3 and press [START] key.
Same
display
Press [START] key.
Press [CUSTOM SETTINGS] key.
66-12
Purpose
Setup
Function (Content)
Used to check the output operation of FAX G3
mode 300BPS.
(Used to check the MODEM operation.)
Signals are sent in the send level set with the
soft switch. (Only when FAX is installed.)
mode 300BPS.
(Used to check the MODEM operation.)
Signals are sent in the send level set with the
soft switch. (Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure A signal of 300bps is outputted.
(Send level is set with soft SW.)
Enter a number during execution to change the
kind of signal.
Press CUSTOM SETTINGS to terminate.
Enter a number during execution to change the
kind of signal.
Press CUSTOM SETTINGS to terminate.
1
NO SIGNAL
No signal
2
11111
3
11110
4
00000
5
010101
6
00001
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111
3.11110
4.00000
5.010101
6.00001
1
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111
3.11110
4.00000
5.010101
6.00001
1
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111
3.11110
4.00000
5.010101
6.00001
2
Press [CUSTOM SETTINGS] key.
Select 2 and press [START] key.
Same
display
Press [START] key.
Press [CUSTOM SETTINGS] key.
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 17 ページ ２００４年１２月１５日 水曜日 午後２時２１分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-18
<List of set values>
*
Dial is send with the setup value of +29ms.
<List of set values>
*
Dial is send with the setup value of +9ms.
66-13
Purpose
Setup
Function (Content)
Used to enter (set) the number for the FAX dial
signal output test. (The dial number signal set
with this simulation is outputted in the dial signal
output test with SIM 66-14~16)
(Only when FAX is installed.)
signal output test. (The dial number signal set
with this simulation is outputted in the dial signal
output test with SIM 66-14~16)
(Only when FAX is installed.)
Section
FAX
Item
Data
Operation/Procedure The dial test number is set.
Enter a number with 10 digit key pad, * key, and
# key.
The upper limit is 20 digits.
Press CLEAR to return to the initial state.
Press START to register.
# key.
The upper limit is 20 digits.
Press CLEAR to return to the initial state.
Press START to register.
66-14
Purpose
Setup
Function (Content)
Used to set the make time in the FAX pulse dial
mode (10PPS) and to test the dial signal output.
(The dial number signal set with SIM 66-13 is
outputted.)
Used to check dialing troubles and the operation.
(Only when FAX is installed.)
mode (10PPS) and to test the dial signal output.
(The dial number signal set with SIM 66-13 is
outputted.)
Used to check dialing troubles and the operation.
(Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure The dial test is performed. (10PPS output)
The make time is set. (Set range : 0-15)
When CUSTOM SETTING is pressed, the
execution is terminated.
When CUSTOM SETTING is pressed, the
execution is terminated.
0
Execution
1
Dial pulse make time setup (0 - 15)
SIMULATION 66-13
DIAL TEST NUMBER SETTING.
INPUT NUMBER AND PRESS START.
DIAL TEST NUMBER SETTING.
INPUT NUMBER AND PRESS START.
0123456789*#01234567
0-9:[0-9], *:[*], #:[ ]
#
SIMULATION 66-14
DIAL TEST(10PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1.MAKE TIME
DIAL TEST(10PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1.MAKE TIME
1
SIMULATION 66-14
DIAL TEST(10PPS). SELECT 0-15, AND PRESS START.
[1.MAKE TIME]
DIAL TEST(10PPS). SELECT 0-15, AND PRESS START.
[1.MAKE TIME]
7
7
; [ ms]
+29
SIMULATION 66-14
DIAL TEST(10PPS). EXECUTING...
1.MAKE TIME
DIAL TEST(10PPS). EXECUTING...
1.MAKE TIME
7
; [ ms]
+29
Select 1 and press [START] key.
Press [CUSTOM SETTINGS] key
or [START] key.
or [START] key.
Select 0 and
press [START] key.
press [START] key.
Press [CUSTOM SETTINGS] key.
66-15
Purpose
Setup
Function (Content)
Used to set the make time in the FAX pulse dial
mode (20PPS) and to test the dial signal output.
(The dial number signal set with SIM 66-13 is
outputted.)
Used to check dialing troubles and the operation.
(Only when FAX is installed.)
mode (20PPS) and to test the dial signal output.
(The dial number signal set with SIM 66-13 is
outputted.)
Used to check dialing troubles and the operation.
(Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure The dial test is performed. (20PPS output)
The make time is set. (Set range : 0-15)
When CUSTOM SETTINGS is pressed, the
execution is terminated.
When CUSTOM SETTINGS is pressed, the
execution is terminated.
0
Execution
1
Dial pulse make time setup (0 - 15)
SIMULATION 66-15
DIAL TEST(20PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1.MAKE TIME
DIAL TEST(20PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1.MAKE TIME
1
SIMULATION 66-15
DIAL TEST(20PPS). SELECT 0-15, AND PRESS START.
[1.MAKE TIME]
DIAL TEST(20PPS). SELECT 0-15, AND PRESS START.
[1.MAKE TIME]
7
7
; [ ms]
+9
SIMULATION 66-15
DIAL TEST(20PPS). EXECUTING...
1.MAKE TIME
DIAL TEST(20PPS). EXECUTING...
1.MAKE TIME
7
; [ ms]
+9
Select 1 and press [START] key.
Press [CUSTOM SETTINGS] key
or [START] key.
or [START] key.
Select 0 and
press [START] key.
press [START] key.
Press [CUSTOM SETTINGS] key.
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 18 ページ ２００４年１２月１５日 水曜日 午後２時２１分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-19
*
For the set value, refer to the soft SW specifications.
<List of set values>
For the set values, refer to the soft SW specifications.
<DTMF signal>
<DTMF signal>
66-16
Purpose
Setup
Function (Content)
Used to test the dial signal (DTMF) output in the
FAX tone dial mode. (The dial number signal set
with SIM 66-13 is outputted.)
The send level can be set to an optional level.
Used to check dialing troubles and the operation.
FAX tone dial mode. (The dial number signal set
with SIM 66-13 is outputted.)
The send level can be set to an optional level.
Used to check dialing troubles and the operation.
Section
FAX
Item
Operation
Operation/Procedure The dial test is performed. (DTMF signal output)
1) The level (dB) setup is made.
(Set range: 0 - 15dB)
2) The difference between high group and low
group is set. (Set range: 0 - 15)
3) When CUSTOM SETTING is pressed,
the execution is terminated.
0
Execution
1
HIGH
High group level
2
HIGH-LOW
High group - low group
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-2, AND PRESS START.
0. EXECUTE
1.HIGH
DIAL TEST(DTMF). SELECT 0-2, AND PRESS START.
0. EXECUTE
1.HIGH
(dB)
2.
1
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
1.HIGH (dB)
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
1.HIGH (dB)
7
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
2.
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
2.
7
7
7
HIGH-LOW
7
7
HIGH-LOW
HIGH-LOW
SIMULATION 66-16
DIAL TEST(DTMF). EXECUTING...
1.HIGH
DIAL TEST(DTMF). EXECUTING...
1.HIGH
(dB)
2.
Select 1 or 2 and press [START] key. Press [CUSTOM SETTINGS] key
or [START] key.
Select 0 and
press [START] key.
press [START] key.
Press [CUSTOM SETTINGS] key.
(When 1 is selected)
(When 2 is selected)
(When 0 is selected)
66-17
Purpose
Setup
Function (Content)
Used to test the dial signal (DTMF) output in the
Fax tone dial mode. Send level Max.
Used to check the dial IC operation.
(Only when FAX is installed.)
Fax tone dial mode. Send level Max.
Used to check the dial IC operation.
(Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure The DTMF signal output is checked.
(Output level 0)
When CUSTOM SETTING is pressed,
the execution is terminated.
When CUSTOM SETTING is pressed,
the execution is terminated.
1 - 9, 0, *, #
66-18
Purpose
Setup
Function (Content)
Used to test the dial signal (DTMF) output in the
Fax tone dial mode.
The send level set with the soft switch is
outputted.
Used to check the dial IC operation.
(Only when FAX is installed.)
Fax tone dial mode.
The send level set with the soft switch is
outputted.
Used to check the dial IC operation.
(Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure The DTMF signal output is checked.
(Output level is set with soft SW.)
When CUSTOM SETTING is pressed,
the execution is terminated.
When CUSTOM SETTING is pressed,
the execution is terminated.
1 - 9, 0, *, #
SIMULATION 66-17
DTMF SIGNAL OUTPUT.(LEVEL MAX) INPUT 0
DTMF SIGNAL OUTPUT.(LEVEL MAX) INPUT 0
9,* ,#, AND PRESS START.
1
SIMULATION 66-17
DTMF SIGNAL OUTPUT.(LEVEL MAX) EXECUTING...
DTMF SIGNAL OUTPUT.(LEVEL MAX) EXECUTING...
1
Press [START] key.
Press [CUSTOM SETTINGS] key.
SIMULATION 66-18
DTMF SIGNAL OUTPUT.(SOFT SW) INPUT 0
DTMF SIGNAL OUTPUT.(SOFT SW) INPUT 0
9,* ,#, AND PRESS START.
1
SIMULATION 66-18
DTMF SIGNAL OUTPUT.(SOFT SW) EXECUTING...
DTMF SIGNAL OUTPUT.(SOFT SW) EXECUTING...
1
Press [START] key.
Press [CUSTOM SETTINGS] key.
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 19 ページ ２００４年１２月１５日 水曜日 午後２時２１分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-20
<Set values>
<Set value>
<List of set values>
66-19
Purpose
Setup
Function (Content)
Used to backup the Address data
(Set values of rapid key dialing) into the flash
Memory (AR-MM9).
(When FAX is installed and FAX extended
memory is installed.)
(Set values of rapid key dialing) into the flash
Memory (AR-MM9).
(When FAX is installed and FAX extended
memory is installed.)
Section
FAX
Item
Operation
Operation/Procedure Address data is backed up into Flash ROM.
Contents of backup data
•One-touch
•FTP expansion
•Group expansion
•Group expansion
•Program
•User index
•Standard sender
•Standard sender
•I-FAX sender registration
•Polling allow number
•Memory box
•Memory box
•Sender's name
•FAX sender
•Subject
•Subject
•File name
•FAX receive select table
•iFAX receive YES/NO
•iFAX receive YES/NO
The data other than the above are not backed
up.
up.
1
Backup executed
2
No backup
66-20
Purpose
Setup
Function (Content)
Used to restore the backup data (SIM 66-19) to
Address data. (When FAX is installed and FAX
extended memory is installed.)
Address data. (When FAX is installed and FAX
extended memory is installed.)
Section
FAX
Item
Operation
Operation/Procedure Address data backed up with SIM 66-19 are read
from the option Flash ROM and written into the
machine.
However, data backed up in the Tiger series
cannot be restored to the machine. If an option
Flash ROM backed up in the Tiger series is
installed, the data in the option Flash ROM are
deleted.
machine.
However, data backed up in the Tiger series
cannot be restored to the machine. If an option
Flash ROM backed up in the Tiger series is
installed, the data in the option Flash ROM are
deleted.
1
1
Press [START] key.
After completion of backup
SIMULATION 66-19
ADDRESS DATA BACK UP. (WRITE TO FLASH ROM)
ARE YOU SURE?
1. YES
2. NO
ADDRESS DATA BACK UP. (WRITE TO FLASH ROM)
ARE YOU SURE?
1. YES
2. NO
SIMULATION 66-19
ADDRESS DATA BACK UP. (WRITE TO FLASH ROM) EXECUTING...
ADDRESS DATA BACK UP. (WRITE TO FLASH ROM) EXECUTING...
1
Read/Write executed
2
Read/Write not executed
66-21
Purpose
Adjustment, setup, operation data output, check
(display, print)
(display, print)
Function (Content)
Used to print the FAX information (registrations,
communication management, file management,
system errors). (Only when FAX is installed.)
communication management, file management,
system errors). (Only when FAX is installed.)
Section
FAX
Item
Data
Operation/Procedure Information related to FAX is printed.
1) Enter the number corresponding to the
information(item) to be printed with 10-key.
2) Press [start] key.
1
REGISTERED
Various registered information
2
MANAGEMENT
Communication management information
3
FILE
MANAGEMENT
MANAGEMENT
File management information
4
SYSTEM ERROR System error information
5
PROTOCOL
Protocol information
1
1
Press [START] key.
After completion of reading
SIMULATION 66-20
ADDRESS DATA (READ FROM FLASH ROM)
ARE YOU SURE ?
1. YES
2. NO
ADDRESS DATA (READ FROM FLASH ROM)
ARE YOU SURE ?
1. YES
2. NO
SIMULATION 66-20
ADDRESS DATA BACK UP. (READ FROM FLASH ROM) EXECUTING...
ADDRESS DATA BACK UP. (READ FROM FLASH ROM) EXECUTING...
0
SIMULATION 66-21
FAX INFORMATION PRINT OUT.EXECUTING...
1. REGISTERED
FAX INFORMATION PRINT OUT.EXECUTING...
1. REGISTERED
SIMULATION 66-21
FAX INFORMATION PRINT OUT. SELECT 1-5, AND PRESS START.
1.REGISTERED
FAX INFORMATION PRINT OUT. SELECT 1-5, AND PRESS START.
1.REGISTERED
2.MANAGEMENT
3.FILE MANAGEMENT
4.SYSTEM ERROR
5.PROTOCOL
Select other than 0 and
press [START] key.
press [START] key.
If there is no print data,
the display returns to the
original state without printing.
the display returns to the
original state without printing.
After completion of printing
(When 1)
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 20 ページ ２００４年１２月１５日 水曜日 午後２時２１分
Click on the first or last page to see other AR-FX12 (serv.man7) service manuals if exist.