Sharp AR-FX12 (serv.man7) Service Manual ▷ View online
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-33
17
6
Not used
0
0
0
7,8 Coding capacity in send/
receive
(Reflected on DIS/DCS/
DTC)
(Other than V.34)
(Reflected on DIS/DCS/
DTC)
(Other than V.34)
Used to set coding capacity to transmit to the other party machine in
a communication of other than V.34.
a communication of other than V.34.
0
0
0
JBIG/MMR/
MR/MH
MR/MH
0
0
0
18 1-4 Not used
0
0
0
1
1
1
0
0
0
0
0
0
5
PIN code conformity
Used to set whether the dial number display of FAX is limited to 16
digits or not. When this item is set to "1: Support," the FAX number
display by the resend key is limited to 16 digits. The display of
completion of the job status is also limited to 16 digits.
digits or not. When this item is set to "1: Support," the FAX number
display by the resend key is limited to 16 digits. The display of
completion of the job status is also limited to 16 digits.
0
0
0
Not conform
6-8 Not used
0
0
0
0
0
0
1
1
1
19 1-7 Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
8
Machine booting when
1300Hz is detected in
the nighttime FAX mode
1300Hz is detected in
the nighttime FAX mode
Used to set whether the machine is booted or not by detection of
1300Hz signal from the line in the nighttime FAX mode. (This serves
as the MDMC PWB jumper in Tiger series.)
When this is changed to "Booted," the machine may be booted by
noises on the line. Check the singles on the line.
1300Hz signal from the line in the nighttime FAX mode. (This serves
as the MDMC PWB jumper in Tiger series.)
When this is changed to "Booted," the machine may be booted by
noises on the line. Check the singles on the line.
0
0
0
Not booting
20
1
CSI send
Used to set whether CSI send is performed or not.
The CSI signal includes the sender's number.
The CSI signal includes the sender's number.
0
0
0
Send
2
DIS reception
confirmation in G3
transmission
confirmation in G3
transmission
Used to set whether DIS reception is conformed or not in G3 mode
transmission (valid only in other than V.34).
This is valid only when communication is made in other than V.34.
transmission (valid only in other than V.34).
This is valid only when communication is made in other than V.34.
0
0
0
0
3,4 Timer setup between
flag and address
(V.21-FSK)
(V.21-FSK)
Used to set the timer between Flag and address when receiving FSK
signal in a communication other than V.34.
signal in a communication other than V.34.
0
0
0
6sec
0
0
0
5
Not used
0
0
0
6
Countermeasures
against echo in
reception
(CED tone send interval)
against echo in
reception
(CED tone send interval)
Used to set the time interval (sec) from sending CED or ANSam to
sending FSK signal of DIS.
sending FSK signal of DIS.
If either SW20-6 or SW2-7 is YES, disconnection of the line after
completion of communication is delayed for 1.5sec.
completion of communication is delayed for 1.5sec.
0
0
0
75msec
SW
No.
Bit
No.
Item
Switch selection and function
EU
Au
Asia
Initial value
Key
operator
Bit No.
7
8
JBIG/MMR/MR/MH
0
0
MMR/MR/MH
0
1
MR/MH
1
0
MH
1
1
1: Conform
0: Not conform
1: Booting
0: Not booting
1: CSI signal not send
0: CSI signal send
1: Reception of DIS
is checked twice.
0: Reception of NSF/DIS is
checked once, reception
without NSF is checked
twice.
without NSF is checked
twice.
Bit No.
3
4
6sec
0
0
15sec
0
1
30sec
1
0
120sec
1
1
1: 500msec
0: 75msec
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 33 ページ ２００４年１２月１５日 水曜日 午後２時２１分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-34
20
7
Countermeasures
against echo in
transmission
(Used to set the hold
time from DIS reception
to signal sending.)
against echo in
transmission
(Used to set the hold
time from DIS reception
to signal sending.)
Used to set the time interval (sec) from DIS reception to DCS signal
sending.
This is valid only in the mode other than V.34.
sending.
This is valid only in the mode other than V.34.
0
0
0
200msec
8
Not used
0
0
0
21 1-3 Setup of call time in auto
transmission
(T0 timer setup)
(T0 timer setup)
Used to set the time (sec) of calling when the other party does not
receive the call in automatic transmission.
The set range is 30 - 75sec in the increment of 15sec by binary input
of N into "(15sec x N) + 30sec." The set range of N is 0 ~ 7. When set
to a value outside the set range, the initial value of the destination is
applied to.
receive the call in automatic transmission.
The set range is 30 - 75sec in the increment of 15sec by binary input
of N into "(15sec x N) + 30sec." The set range of N is 0 ~ 7. When set
to a value outside the set range, the initial value of the destination is
applied to.
0
0
0
45sec
Send
setup
setup
0
0
0
1
1
1
4-7 T1 timer setup
Used to set the time (sec) for connection of line when the other party
does not respond in FAX communication.
The set range is 30 - 105sec in the increment of 5sec by binary input
of N into "(5sec x N) + 30sec." N is set in the range of 0 - 15. T1 timer
is the timer for the time from recognition of FAX CED or DCS) by the
other party after connection of line. The ITU-T standard is 35 ± 5sec.
does not respond in FAX communication.
The set range is 30 - 105sec in the increment of 5sec by binary input
of N into "(5sec x N) + 30sec." N is set in the range of 0 - 15. T1 timer
is the timer for the time from recognition of FAX CED or DCS) by the
other party after connection of line. The ITU-T standard is 35 ± 5sec.
0
0
0
40sec
0
0
0
1
1
1
0
0
0
8
Not used
0
0
0
22 1-4 Not used
0
0
0
0
0
0
0
0
0
0
0
0
5,6 T4 timer setup at auto
mode
(+1.5sec for manual)
(+1.5sec for manual)
Used to set the timer up to respond and receive.
Timer for DCS signal to respond and receive.
For the ITU-T standard, 3sec ± 15%.
Timer for DCS signal to respond and receive.
For the ITU-T standard, 3sec ± 15%.
0
0
0
3sec
0
0
0
7,8 Not used
0
0
0
0
0
0
23
1
EOL detection timer
Used to set the detection timer (sec) of EOL (End Of Line) in Phase C
reception of G3 mode.
reception of G3 mode.
If an error occurs in EOL detection, it is processed as EOL not
detected.
detected.
0
0
0
13sec
2-6 Not used
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
7,8 RTN send line error rate Used to set the threshold value for judgment of RTN sending in G3
reception. The threshold value is of STD conversion. The half of this
value is used for judgment of RTP sending.
value is used for judgment of RTP sending.
When, for example, FINE is received, the threshold value is doubled.
1
1
1
60 lines
0
0
0
24
1
DCS-TCF interval time
Used to set the time interval (sec) from DCS sending to TCF signal
sending.
sending.
The ITU-T standard is 75 ± 20ms.
0
0
0
75msec
SW
No.
Bit
No.
Item
Switch selection and function
EU
Au
Asia
Initial value
Key
operator
1: 500msec
0: 200msec
Bit No.
5
6
3sec
0
0
4sec
0
1
5sec
1
0
6sec
1
1
1: 25sec
0: 13sec
Bit No.
7
8
6 liens
0
0
12 lines
0
1
60 lines
1
0
120 lines
1
1
1: 150msec
0: 75msec
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 34 ページ ２００４年１２月１５日 水曜日 午後２時２１分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-35
24
2
EQM judgment
threshold value
when confirming TCF
reception
threshold value
when confirming TCF
reception
Used to set whether the threshold value (FTT) is set severely or
loosely for EQM judgment in confirmation of TCF reception.
loosely for EQM judgment in confirmation of TCF reception.
If set loosely, TCF is easy to return CFR, but apt to cause an error in
PIX (Phase C).
PIX (Phase C).
0
0
0
Severely
3
Judgment method in
confirmation of TCF
reception
confirmation of TCF
reception
Used to set the judgment method of FTT in confirmation of TCF
reception.
reception.
0
0
0
0
4
Not used
0
0
0
5
Simplified ACR function
0
0
0
Function OFF
6
CED signal send
Used to set whether CED signal is sent or not.
Valid only when SW43.1 (V.34 mode function ) is OFF.
This is because ANSam signal is indispensable in V.34 mode.
This is because ANSam signal is indispensable in V.34 mode.
0
0
0
Send
7,8 CED signal send time
Used to set the time for CED signal send.
ANSam signal follows SW46-7 ~ 8.
0
0
0
3sec
0
0
0
25 1,2 CED/ANSam send start
wait time
Used to set the wait time for sending CED/ANSam signals to the line
from FAX reception state after connection of the line.
from FAX reception state after connection of the line.
0
0
0
2.25sec
0
0
0
3,4 CNG send time
Used to set the wait time from connection of the line to sending of
CNG signal to the line.
CNG signal to the line.
0
0
0*
* Taiwan: 1
0.5sec
2.0sec (Taiwan
only)
2.0sec (Taiwan
only)
0
0
0*
5
CED detection time
Used to set the wait time for determination of the signal when
detecting CED/ANSam signal.
detecting CED/ANSam signal.
0
0
0
500ms
6-8 Not used
0
0
0
0
0
0
0
0
0
26 1,2 Number of times of RCP
send
Used to set the number of times of RCP send when sending Phase C
in ECM system.
in ECM system.
When the other party cannot detect the RCP frame, it becomes easy
to detect RCP.
to detect RCP.
0
0
0
3 times
0
0
0
SW
No.
Bit
No.
Item
Switch selection and function
EU
Au
Asia
Initial value
Key
operator
1: Loosely
0: Severely
1: Judged by EQM
value. TCF is
checked loosely.
checked loosely.
0: Received data is judged to
be 0 or not, and EQM value
is judged.
is judged.
1: Function ON
0: Function OFF
1:CED signal is not sent.
0:CED signal is sent.
Bit No.
7
8
3sec
0
0
4sec
0
1
5sec
1
0
6sec
1
1
Bit No.
1
2
2.25sec
0
0
3sec
0
1
4sec
1
0
2.25sec
1
1
Bit No.
3
4
0.5sec
0
0
1sec
0
1
1.5sec
1
0
2.0sec
1
1
1: 1000ms
0: 500ms
Bit No.
1
2
3 times
0
0
6 times
0
1
9 times
1
0
12 times
1
1
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 35 ページ ２００４年１２月１５日 水曜日 午後２時２１分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-36
26
3
Number of RTC EOL
send
send
Used to set how many EOL's are sent as RTC when sending Phase
C.
C.
When the other party cannot detect the RCP, it becomes easy to
detect RCP.
detect RCP.
0
0
0
6 times
4-8 Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
27 1-4 Echo suppressor tone
setup
Used to set YES/NO of echo suppressor tone in each high-speed
modulation system.
modulation system.
0
0
0
YES
(No for V.29
only)
(No for V.29
only)
0
0
0
1
1
1
0
0
0
5-8 Not used
0
0
0
1
1
1
1
1
1
1
1
1
28 1-8 Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
29 1-5 FAX paper exit tray
setting
Used to specify the default output tray in the combination of each
output
system. The combinations of the output trays are as follows.
In the case of the main unit only or the main unit without the manual
feed tray
and with the duplex tray, the output is always made from the center
tray.
output
system. The combinations of the output trays are as follows.
In the case of the main unit only or the main unit without the manual
feed tray
and with the duplex tray, the output is always made from the center
tray.
0
0
0
Receive
setup
setup
0
0
0
0
0
0
0
0
0
0
0
0
6-8 Not used
0
0
0
0
0
0
0
0
0
30
1
Not used
0
0
0
2
Error reception in RTN
reception
reception
Used to set whether RTN signal reception is judged as an error or
not. (Only in G3 mode)
not. (Only in G3 mode)
0
0
0
Judges as an
error
error
SW
No.
Bit
No.
Item
Switch selection and function
EU
Au
Asia
Initial value
Key
operator
1: 12 times
0: 6 times
Bit No.
V.33
1
1 : NO
0 : YES
V.17
2
1 : NO
0 : YES
V.29
3
1 : NO
0 : YES
V.27
4
1 : NO
0 : YES
Bit No.
Main unit + Manual Duplex
1
1:CENTER
TRAY
TRAY
0:LEFT
TRAY
TRAY
Finisher + Duplex /
Finisher
Finisher
2
1:FINISHER
TOP TRAY
TOP TRAY
0:LEFT
TRAY
TRAY
Mail bin stacker + Duplex /
Mail bin stacker
Mail bin stacker
3
1:MAIL BIN
TOP TRAY
TOP TRAY
0:LEFT
TRAY
TRAY
Main unit + Saddle finisher
+ Duplex
+ Duplex
4
1:CENTER
TRAY
TRAY
0:FINISHER
TRAY
TRAY
Mail bin stacker + Saddle
finisher
finisher
5
1:MAIL BIN
TOP TRAY
TOP TRAY
0:FINISHER
TRAY
TRAY
1: RTN reception is not
judged as an error.
0: RTN reception is
judged as an error.
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 36 ページ ２００４年１２月１５日 水曜日 午後２時２１分
Click on the first or last page to see other AR-FX12 (serv.man7) service manuals if exist.