Sharp AR-FX12 (serv.man7) Service Manual ▷ View online
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-25
6. FAX software switch
A. SOFT SW SETUP CHANGE QUICK REFERENCE
Large item
Medium item
Content of switch
Key operator Soft SW No.
Purpose of use
Dial (Calling)
Remote
machine
calling disable
machine
calling disable
Detection of line current when dialing
SW 70-5
Dial disable
Dial call wait time
SW 62-1~2
Dial disable/Erroneous dialing
Pause time setup (between dialing)
Initial setup
SW 70-1~4
Dial disable/Erroneous dialing
Tone/Pulse default setup (Dial ringing signal
setup)
setup)
Initial setup
SW 62-5~6
Dial disable
•DTMF signal level (high group)
•DTMF send level (low group)
•DTMF send level (low group)
•DTMF signal send time
•DTMF minimum pause time setup
SW 66-5~8
Dial disable in PB (PB/FAX service, etc.)
SW 67-1~4
Dial disable in PB (PB/FAX service, etc.)
SW 68-1~5
Dial disable in PB (PB/FAX service, etc.)
SW 69-1~8
Dial disable in PB (PB/FAX service, etc.)
Make time (10PPS) setup
SW 63-1~4
Dial disable in pulse
Break time (10PPS)setup
SW 63-5~8
Dial disable in pulse
Minimum pause (10PPS)setup
SW 64-1~4
Dial disable in pulse
Signal
detection
detection
Busy tone detection
SW 71-3
Busy tone detection disable
Busy tone detection cycle
SW 71-4~5
Busy tone detection error
DT/BT detection level
SW 71-6~7
Busy tone detection disable
Dial tone detection
SW 70-6
Dial tone detection disable
Dial tone monitor time
SW 70-7
Dial tone detection error
Lower limit of busy tone detection time
(ON time)
(ON time)
SW 72-1~2
Busy tone detection error
Upper limit of busy tone detection time
(ON time)
(ON time)
SW 72-3~4
Busy tone detection error
Frequency range setup for detection of DT/
BT
BT
SW 71-1~2
Dial tone/busy tone detection error
Redial
Remote
machine not
responding
machine not
responding
Resend when no response from the other
party
party
SW 56-8
No recall wanted when remote machine
not responding
not responding
Error
Number of times of recall in communication
error
error
send setup
SW 57-5~8
Error
Recall allowed in communication error
Send setup
SW 59-3
Error
Recall interval in communication error
SW 58-5~8
Busy
Recall interval in busy state
send setup
SW 57-1~4
Busy
Number of times of recall in busy
send setup
SW 58-1~4
Busy
Recall allowed in busy
send setup
SW 59-2
Reception
(Calling)
(Calling)
Not receiving
Number of calls for auto receives
Receive
setup
setup
SW 3-5~8
Number of reception call
Auto/Manual default setup
User setup
SW 7-2
Initial setup of auto reception/manual
reception
reception
CI detection
disable
disable
Lower limit of call signal ON time
SW 75-1~4
CI signal detection disable
Upper limit of call signal ON time
SW 75-5~8
CI signal detection disable
Lower limit of call signal OFF time
SW 76-1~4
Ci signal detection disable
Upper limit of call signal OFF time
SW 76-5~6
CI signal detection disable
Call signal OFF non-detection time
SW 77-1~4
CI signal detection disable
External
telephone
handset
telephone
handset
External
telephone
connection
telephone
connection
External telephone connection
Initial setup
SW 3-2
External telephone connection
External
telephone off-
hook detection
telephone off-
hook detection
External telephone off-hook detection time
SW 12-1~8
External telephone off-hook detection
error
error
Remote switch
number
number
Remote switch number setup
Initial setup
SW 13-1~8
Remote switch detection error
Remote switch
setup
setup
Remote reception instruction
SW 14-1
Remote switch inhibit
Notification to external telephone in remote
switch
switch
SW 14-2
Remote switch operation allowed
SW 14-3
Remote switch is made when calling
from external telephone.
from external telephone.
[06]SIMULATIONS ・ FAXSOFTWARESWITCH.fm 25 ページ 2004年12月15日 水曜日 午後2時21分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-26
TEL/FAX auto
switch
switch
Voice answering send level to the line
SW 51-1
External
telephone call
telephone call
Ring back tone ON time
SW 10-1~4
External telephone call disable
CNG detection disable
CNG detection disable
Ring back tone OFF time
SW 10-5~8
External telephone call disable
CNG detection disable
CNG detection disable
Communication
General
Signal send level
SW 15-1~8
When the remote machine does not
receive signals in a proper level.
receive signals in a proper level.
ECM (Valid for other than V.34)
(Reflected on V.21 DIS/DCS.)
(Reflected on V.21 DIS/DCS.)
Initial setup
SW 17-5
Error resend frequently occurs, resulting
in extended communication time.
in extended communication time.
Timer setup between flag and address
(V.21-FSK)
(V.21-FSK)
SW 20-3~4
Communication error in a satellite line
Coding capacity in send/receive
(V.34 communication)
(Reflected on DIS/DCS/DTC.)
(V.34 communication)
(Reflected on DIS/DCS/DTC.)
SW 17-3~4
Error in JBIG mode
Coding capacity in send/receive
(Reflected on DIS/DCS/DTC)
(Other than V.34)
(Reflected on DIS/DCS/DTC)
(Other than V.34)
SW 17-7~8
Error in JBIG mode
SG3
V.34 mode function(When call out and
polling)
polling)
SW 43-1
Frequent errors in SG3 communication
CED detection time
SW 43-3~6
Frequent errors in SG3 communication
V.34 mode function in manual
communication
communication
SW 42-8
Frequent errors in SG3 communication in
FAX service
FAX service
Send
G3/SG3
Countermeasures against echo in
transmission
(Used to set the hold time from DIS reception
to signal sending.)
transmission
(Used to set the hold time from DIS reception
to signal sending.)
SW 20-7
An error occurs in phase B.
DIS reception confirmation in G3
transmission
transmission
SW 20-2
An error occurs in phase B.
CED detection time
SW 25-5
CED signal detection error
SG3
V.34 mode transmission speed
SW 44-1~4
An error occurs in SG3 communication.
G3
Echo suppresser tone setup
SW 27-1~4
An error occurs in V.29 communication
Modem transmission speed (Except for V.34)
(DCS)
(DCS)
SW 16-1~4
To uncertain/certain receiver
DCS-TCF interval time
SW 24-1
An error occurs in training.
Error process in RTN reception
SW 30-2
OK is displayed when RTN is received.
Receive
G3/SG3
CSI send
SW 20-1
SG3
V.34 mode reception speed
SW 44-5~8
An error occurs in SG3 communication.
G3
Countermeasures against echo in reception
(CED tone send interval)
(CED tone send interval)
SW 20-6
An error occurs n phase B in reception.
Reception modem speed fixed
(other than V.34) (DIS)
(other than V.34) (DIS)
SW 16-5~6
Fall back or an error occurs due to poor
line conditions.
line conditions.
EOL detection timer
SW 23-1
EOL time up occurs frequently.
RTN send line error rate
SW 23-7~8
Line error occurs frequently.
EQM judgment threshold value
when confirming TCF reception
when confirming TCF reception
SW 24-2
TCF reception error occurs.
Judgment method in confirmation of TCF
reception
reception
SW 24-3
TCF reception error occurs.
Receive print
Paper
selection
selection
Sub scan length judgment
SW 35-2
Print is not made on the selected paper.
FAX paper exit tray setup
Receive setup
SW 29-1~5
Print is not made on the selected paper.
Received data print condition setup
Receive setup
SW 35-3~4
To make divided print instead of
reduction print.
reduction print.
Automatic reduction/dispose setup
Receive setup
SW 35-7
To disable reduction print.
Setup of magnification ratio in automatic
reduction
reduction
SW 36-1~8
To disable reduction print on fixed size
paper.
paper.
Reduction/dispose setup when printing A3,
11X 17
11X 17
SW 35-8
Print is not made on the selected paper
when A3-11x17 size document is
received.
when A3-11x17 size document is
received.
Duplex reception print
Receive setup
SW 34-8
To make duplex print of received
document
document
Rotation print
SW 35-1
To disable rotation print
Received document output setup
SW 35-5
To print after reception of each page
11 x 17 paper reception width setup
SW 37-3
To print 11x17 document as B4 width
Reception size specification
(Indicates reception capacity.)
(Indicates reception capacity.)
SW 37-1~2
To limit the reception size.
Large item
Medium item
Content of switch
Key operator Soft SW No.
Purpose of use
[06]SIMULATIONS ・ FAXSOFTWARESWITCH.fm 26 ページ 2004年12月15日 水曜日 午後2時21分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-27
B. Details
EU: U.K., France, German, Sweden
Au: Australia, New Zealand
Asia: China, Singapore, Indonesia, Thailand, Malaysia, India, Taiwan
SW
No.
Bit
No.
Item
Switch selection and function
EU
Au
Asia
Initial value
Key
operator
1
1-8 Country code
Country code set by ITU-T. Control is made according to the set
country code.
country code.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
2
1
TSI judgment setting
when a certain number
receive reject
(No signal or all space)
when a certain number
receive reject
(No signal or all space)
Used to set receive reject or receive allow when there is no TSI signal
from the remote machine or when the TSI signal is all space, when a
certain number receive reject is set to valid by the key operation.
from the remote machine or when the TSI signal is all space, when a
certain number receive reject is set to valid by the key operation.
0
0
0
Receive allow
2
Specified number
receive rejection setup
(FAX)
receive rejection setup
(FAX)
Used to set whether a certain number receive reject by FAX is
Enabled or Disabled. In auto receive only.
Enabled or Disabled. In auto receive only.
0
0
0
Specified
number receive
ignored
(Invalid)
number receive
ignored
(Invalid)
Receive
setup
setup
3
Manual receive mode
receive rejection setup
(FAX)
receive rejection setup
(FAX)
Used to set whether a certain number receive reject by FAX is
Enabled or Disabled. In manual receive only.
Enabled or Disabled. In manual receive only.
0
0
0
Specified
number
ignored
number
ignored
4
Manual receive mode
auto receive switch
setup
auto receive switch
setup
Used to set whether auto receive switch is performed or not in the
manual receive mode.The number of switching to auto receive is set
with SW2-5-8.
manual receive mode.The number of switching to auto receive is set
with SW2-5-8.
0
0
0
Inhibit
Receive
setup
setup
5-8 Number of calls to
switch to auto receive in
manual receive
manual receive
Used to set the number of calls to switch to auto receive in manual
receive mode.
This function is valid only when SW2-4 is set to "1: Allow (to switch)."
If a value outside the set range is inputted, the default setup is made.
receive mode.
This function is valid only when SW2-4 is set to "1: Allow (to switch)."
If a value outside the set range is inputted, the default setup is made.
1
1
1
9
Receive
setup
setup
0
0
0
0
0
0
1
1
1
3
1
Not used
0
0
0
2
External telephone
connection
connection
Setting to use an external telephone. If not set to YES, an external
telephone cannot be used.
telephone cannot be used.
In North America, users cannot set this switch to "0: NO."
1
1
1
YES
Initial
setup
setup
3
Default finish stamp
Used to set whether the finish stamp is used or not after completion
of document scan when the SPF/RSPF is used.
of document scan when the SPF/RSPF is used.
If a document feed unit other than the SPF/RSPF is used, this setup is
invalid.
invalid.
0
0
0
NO
Operation
setup
setup
4
Not used
0
0
0
5-8 Number of calls for auto
receives
Used to set the number of calls to start auto receive (to catch the
line). Setup is made in the range of 0 ~ 15 by binary input.
When set to 0, no ringing is made. For the nighttime FAX mode (main
SW OFF, memory SW ON), however, ringing of an external telephone
is made.
line). Setup is made in the range of 0 ~ 15 by binary input.
When set to 0, no ringing is made. For the nighttime FAX mode (main
SW OFF, memory SW ON), however, ringing of an external telephone
is made.
0
0
0
2
Receive
setup
setup
0
0
0
1
1
1
0
0
0
Bit No.
1
2
3
4
5
6
7
8
U.K.
1
0
1
1
0
1
0
0
France
0
0
1
1
1
1
0
1
German
0
0
0
0
0
1
0
0
Sweden
1
0
1
0
0
1
0
1
New Zealand
0
1
1
1
1
1
1
0
Australia
0
0
0
0
1
0
0
1
China
0
0
1
0
0
1
1
0
Singapore
1
0
0
1
1
1
0
0
Indonesia
0
1
0
1
0
1
0
0
Thailand
1
0
1
0
1
0
0
1
Malaysia
0
1
1
0
1
1
0
0
India
0
1
0
1
0
0
1
1
Taiwan
1
1
1
1
1
1
1
0
1: Receive reject
0: Receive allow
1: Specified number
receive rejection (Valid)
receive rejection (Valid)
0: Specified number
receive ignored (Invalid)
receive ignored (Invalid)
1: Specified number
receive rejection
receive rejection
0: Specified number
receive ignored(OFF)
receive ignored(OFF)
1: Allow(Switched)
0: Inhibit (Not switched)
1: External telephone YES 0: External Telephone NO
1: Finish stamp used
0: Finish stamp not used
[06]SIMULATIONS ・ FAXSOFTWARESWITCH.fm 27 ページ 2004年12月15日 水曜日 午後2時21分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-28
4
1,2 Not used
0
0
0
0
0
0
3
Polling protection
Used to set Enable/Disable of confidential protection (inhibition of
transmission to erroneous party) in transmission of bulletin board.
Confidential protection is made by collating the number registered in
this machine and that in the other party machine. Sender's number
and send request allow number are collated each other. In this
machine, Sharp's unique collating of system number
transmission to erroneous party) in transmission of bulletin board.
Confidential protection is made by collating the number registered in
this machine and that in the other party machine. Sender's number
and send request allow number are collated each other. In this
machine, Sharp's unique collating of system number
ID
number is not performed.
0
0
0
Protect
Polling
security
setup
security
setup
4
Relay data output
Used to set whether the document received from the relay station is
outputted or not when relay broadcast reception is made.
outputted or not when relay broadcast reception is made.
Similar to F code relay broadcast indicating reception.
0
0
0
Output
5
Not used
0
0
0
6
F code relay broadcast
function
function
Used to set whether relay broadcast transmission is made by
receiving F code relay broadcast instruction from the other party or F
code relay broadcast instruction is not received (even though the
relay box number by SUB is matched on). Though this item is set to
"without this function," F code relay broad cast instruction can be
transmitted.
receiving F code relay broadcast instruction from the other party or F
code relay broadcast instruction is not received (even though the
relay box number by SUB is matched on). Though this item is set to
"without this function," F code relay broad cast instruction can be
transmitted.
0
0
0
Allowed
7
F code confidential
reception
reception
Used to set YES/NO of F code confidential reception from the other
party (even though the confidential box number is matched by SUB).
Though this item is set to NO, F code confidential transmission can
be made.
party (even though the confidential box number is matched by SUB).
Though this item is set to NO, F code confidential transmission can
be made.
0
0
0
Receive
8
F code communication
error process
error process
Used to set YES/NO of resend in F code transmission.
When, however, SW59-3 (Recall allow in communication error) is set
to 0 (Inhibit), recall is not made.
When, however, SW59-3 (Recall allow in communication error) is set
to 0 (Inhibit), recall is not made.
0
0
0
Resend
5
1
F code password
transmission setup
when the other party
has no function of
password
transmission setup
when the other party
has no function of
password
Used when the other party machine has no function of F code
password in F code transmission.
password in F code transmission.
0
0
0
Line dis-
connection with
DCN
connection with
DCN
2,3 Image quality in
reception
(Reflected on DIS, not
reflected on DTC)
(Reflected on DIS, not
reflected on DTC)
Used to set reception image resolution in FAX reception ringing (DIS
send).
send).
0
0
0
Ultra fine
0
0
0
4-8 Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
6
1
SUB capacity in
reception
reception
Used to set SUB capacity (Bit 49) to "1" in reception (DIS send).
0
0
0
YES
SW
No.
Bit
No.
Item
Switch selection and function
EU
Au
Asia
Initial value
Key
operator
1: Not protected
0: Protected
1: Document received
from relay station is not
outputted.
outputted.
0: Document received
from relay station is
outputted.
outputted.
1: F code relay broadcast
instruction is not
received even from
allowed party.
(Judged as
a communication error.)
received even from
allowed party.
(Judged as
a communication error.)
0: F code relay
broadcast instruction
is received from
allowed party.
is received from
allowed party.
1: F code confidential
reception inhibited (Judged
as a communication error.)
as a communication error.)
0: F code confidential
reception allowed.
1: Not resend
0: Resend
1: Send with password
0: Disconnecting of line
with DCN
Bit No.
2
3
Standard
1
1
Fine
1
0
Super fine
0
1
Ultra fine
0
0
1: NO (Set to 0)
0: YES (Set to 1)
[06]SIMULATIONS ・ FAXSOFTWARESWITCH.fm 28 ページ 2004年12月15日 水曜日 午後2時21分
Click on the first or last page to see other AR-FX12 (serv.man7) service manuals if exist.